regalo 1250 Top of Stair Safety Gate Owner’s Manual
- June 12, 2024
- regalo
Table of Contents
regalo 1250 Top of Stair Safety Gate
Product Information
- Models: 1250, 1250 B
- Made in China
- Proper installation is important to ensure stability and prevent dislodging from the doorway.
- The product is designed for child safety.
Product Usage Instructions
- Before assembly, ensure that you have all the necessary parts listed in the manual.
- Install the hinges on the right side of the stairs, at least 6 inches from the edge of the top stair.
- Place the lower mount wall hinge against the wall and position it so that the upper hole of the lower mount wall hinge is at a maximum of 2 1/2 inches above your floor.
- Use the supplied wood screws to screw through the lower mount wall hinge into the drywall and stud. Repeat for the top and bottom holes. Pre-drill a 1/8-inch hole before putting screws in.
- Repeat step 4 with the wall mount hinge snap female. The distance between the top hole of the lower mount wall hinge and the lower hole of the wall mount hinge snap female is 25 inches.
- Screw the top hinge adjuster knob into the main gate panel. Repeat with the lower knob as well. Rotating the hinge in a clockwise direction will bring the hinge in. Loosen the jam nut all the way back.
- Screw the top receiver adjustment knob into the second gate panel. Repeat with the lower knob as well. Rotating the receiver in a clockwise direction will bring the receiver in. Loosen the jam nut all the way back.
- Place the main gate panel with the hinge adjuster knobs into the upper and lower hinges on the wall. Press the main gate panel in a downward motion to set the hinge adjuster knobs into the hinges.
- Place the second gate panel with the receiver adjustment knob in front of the hanging main gate panel. Slide the main gate panel to the left so that the receiver adjustment knobs are approximately 1/4 inch from the wall. When the panels are correctly aligned, there will be no space between the vertical bars on each panel.
READ ALL INSTRUCTIONS BEFORE ASSEMBLY AND USE OF GATE.
KEEP INSTRUCTIONS FOR FUTURE USE
Before Using Product
Read and follow all instructions carefully to ensure that your gate is properly installed. Improper installation could result in the gate becoming unstable or dislodged from the doorway. The safety of your child is your responsibility. Please keep these instructions for your reference.
IMPORTANT
- Mounting hardware must be mounted into a stud in the wall.
- Gate must be mounted at the top of the stairway, at least 6″ back from the front edge of the top stair.
- Hinge must be on the right side when facing the closed gate.
- Gate must swing away from stairs when opening.
MODEL NO. 1250 & 1250 B
Manufacturer recommendations:
- For children ages 6 months to 24 months
- When mounting:
- The minimum opening allowed is 24″
- The maximum opening allowed is 40.5″
- The maximum spacing from the floor to bottom of the gate is 2 1/2″
- The maximum spacing from the wall to the tube is 2 1/2″
- The minimum spacing from the edge of the top stair to the gate is 6″
WARNING
- Install according to manufacturer’s instructions.
- To prevent serious injury or death, securely install gate or enclosure and use according to manufacturer’s instructions.
- Children have died or been seriously injured when gates are not securely installed. ALWAYS install and use gates as directed using all required parts.
- Never stack gates on top of each other to form a taller barrier. This could result in serious injury or death.
- STOP using when a child can climb over or dislodge the gate.
- Use only with the locking/latching mechanism securely engaged.
- Install 6 inches away from top of stairs.
- NEVER use to keep child away from pool.
- Intended for use with children from 6 months through 24 months.
- Always ensure the gate is resting against the floor before beginning installation.
- This product will not necessarily prevent all accidents. Never leave child unattended.
- Check the gate regularly to see if all the hardware and mountings are tightened.
- Do not use if any components are missing or damaged.
- Adult assembly required.
Before Assembly
PLEASE CHECK TO MAKE SURE YOU HAVE THE FOLLOWING PARTS:
- Main Gate Panel (2)
- Wall Mount Hinge, Snap, Male (1)
- Wall Mount Hinge, Snap, Female (1)
- Upper Assembly, Mount Wall, Latch (A) (1)
- Lower, Mount, Wall, Hinge (1)
- Lower, Mount, Wall Latch (A) (1)
- Hinge Adjuster Knob (2)
- Receiver Adjustment Knob (2)
- 2″ Wood Screw (8) Coupler, Male (2)
- Coupler, Female (2)
- Handle Mounting Paper (1)
- Hinge Mounting Paper (1)
- Upper Assembly, Mount Wall, Latch (B) (1)
- Lower, Mount, Wall Latch (B) (1)
Hinge Placement
-
STEP 1
The hinges get installed on the right side of the stairs (when looking down the stairs). Using a stud finder locate a stud in the wall that is at a minimum 6″ from the edge of the top stair. Once the stud is located, place the lower mount wall hinge against the wall. Position it so the upper hole of the lower mount wall hinge is at a maximum of 2 1/2″ above your floor.
NOTE : Use (D,F) or (N,O) to stop gate from swinging over stairwell. Parts are marked with “A” and “B” on backside. -
STEP 2
Using the supplied 2″ wood screws, screw through the lower mount wall hinge into the drywall and stud. Do this for the top and bottom hole
NOTE : Use the handle and hinge mounting (L,M) paper to help mark the exact location.
NOTE : Pre-drill 1/8″ hole before putting screws in. -
STEP 3
Repeat with the wall mount hinge snap female. The distance between the top hole of the lower mount wall hinge and the lower hole of the wall mount hinge snap female is 25″.
Gate Assembly
-
STEP 1
Screw the top hinge adjuster knob into the main gate panel. Repeat with the lower knob as well. Rotating the hinge in the clockwise direction will bring the hinge in. Loosen the jam nut all the way back -
STEP 2
Screw the top receiver adjustment knob into the second gate panel. Repeat with the lower knob as well. Rotating the receiver in the clockwise direction will bring the receiver in. Loosen the jam nut all the way back. -
STEP 3
Place the main gate panel with the hinge adjuster knobs into the upper and lower hinges on the wall. Press the main gate panel in a downward motion to set the hinge adjuster knobs into the hinges.
-
STEP 4
Place the second gate panel with the receiver adjustment knob in front of the hanging main gate panel. Slide the main gate panel to the left so that the receiver adjustment knobs are approximately 1/4″ from the wall. When the panels are correctly aligned there will be no space between the vertical bars on each panel
-
STEP 5
In the center of the two panels place the coupler male, and coupler female. The coupler male goes on the inside of the gate. Put one at the top of the gate and another at the bottom. Place them between the vertical bars and slide them to the top and bottom. Next take the coupler female and place them over the horizontal top and bottom bar and snap it together with the coupler male
Receiver Placement
STEP 1
With the gate in closed position (creating a 90° angle to the wall the hinges
are on) place the receiver adjustment knob in the latch assembly wall mount (D
or N). Mark the location of the holes, making sure you are located on top of a
stud. Do this for the upper and lower latch wall mounts (F or O).
NOTE : Use the handle and hinge mounting paper (L,M) to help mark exact
location of upper and lower wall mounts. Must use parts D with F and N with O.
STEP 2
Open the gate (swing it away from the stairs). Mount the upper and lower
receivers using the 2″ wood screw.
NOTE : Use (D,F) or (N,O) to stop gate from swinging over stairwell. Parts are marked with “A” and “B” on backside. Do not assemble with gate swinging over stairwell.
Final Adjustments
STEP 1
When the gate is in the closed and latched position there should be no
larger than a 2 1/2″ gap from the wall to the first picket on either side. To
achieve this either screw inward or outward the hinge adjustment knobs and/or
the receiver adjuster knobs.
STEP 2
Once the 2 1/2″ maximum gap is set, tighten down the 4 jam nuts with a 13mm
wrench. One on each hinge adjustment knob and one on each receiver adjuster
knob.
STEP 3
Install the wall mount hinge snap female over the wall mount hinge snap male.
Do so by matching the “legs” of the wall mount hinge snap female over the
grooves, and sliding down until it clicks into place of the wall mount hinge
snap male.
To remove hinge snap, with two fingers, gently pull both legs outward and
slide hinge snap upward
STEP 4
To open the gate. Rotate the latch of the latch assembly wall mount in the
clockwise direction to release the gate. Lift the gate upward and away from
the stairs. Pivot the gate in the hinges until fully open.
CARE AND MAINTENANCE
Periodically check the gate for signs of damage, wear, or missing components.
Do not use if any part is missing, worn or damaged. Check the gate regularly
to ensure all the hardware and mountings are tightened. Do not use abrasive
cleaners or bleach. Clean by sponging with warm water and a mild detergent.
WARRANTY
90 DAYS LIMITED WARRANTY
If, during the first 90 days after consumer purchase of the item, under reasonable and non-commercial use and conditions of maintenance, it fails while owned by the original purchaser because of the quality of materials or workmanship of finish and assembly, Regalo International, LLC, will replace or repair it at Regalo’s option. PROOF OF PURCHASE REQUIRED
www.regalo-baby.com
Regalo International, LLC.
3200 Corporate Center Drive, Suite 100
Burnsville, MN 55306, USA
866.272.5274 (U.S. only) or 952.435.1080
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>