regalo 1176 B Home Accents Widespan Baby Safety Gate Instruction Manual

1176 B Home Accents Widespan Baby Safety Gate
Instruction Manual

• READ ALL INSTRUCTIONS BEFORE ASSEMBLY AND USE OF GATE.
  KEEP INSTRUCTIONS FOR FUTURE USE.

Before Assembly

PLEASE CHECK TO MAKE SURE YOU HAVE THE FOLLOWING PARTS:

BEFORE USING PRODUCT
Read and follow all instructions carefully to ensure that your gate and extensions are properly installed. Improper installation could result in the gate becoming unstable or dislodged from the doorway. Always make sure the extension is securely attached to the gate before using it. The safety of your child is your responsibility. Please keep these instructions for your reference.

IMPORTANT

• If hardware is mounting to a surface other than drywall or wood, please consult with a professional about installation.
• Base locks are to be used at all times, on both sides of the gate.

MANUFACTURER RECOMMENDATIONS:

• For children ages 6 months to 24 months

When mounting:

• The minimum opening allowed is 56″
• The maximum opening allowed is 74 1/2″. Please note if your opening is larger than 74 1/2′ y0u can purchase the optional Home Accents™ 2 Panel Extension Kit, model number 0076.

CARE AND MAINTENANCE
Periodically check the gate for signs of damage, wear, or missing components.
Do not use if any part is missing, worn, or damaged. Check the gate regularly to ensure all the hardware and mountings are tightened. Do not use abrasive cleaners or bleach.  Clean by sponging with warm water and mild detergent.

90 DAYS LIMITED WARRANTY
If during the first 90 days after consumer purchase of the item, under reasonable and non-commercial use and conditions of maintenance, it fails while owned by the original purchaser because of the quality of materials or workmanship of finish and assembly, Regalo International, LLC, will replace or repair it at Regalo’s option. PROOF OF  PURCHASE IS REQUIRED.

Gate Assembly

Start with the main gate assemblies (A).
Loosen the hinge knob in the clockwise direction. Doing this will let main gate assemblies unfold.

Slide the two gate assemblies together. Place the door frame u-bracket (F) over the lower frame lining over the four (4) holes. Using the alien wrench (D) tighten down the four  (4) pan head screws (B). Rotate the alien wrench in the clockwise direction to tighten the screws.

Set the door frame assembly (G) into the gate.
Set the pin of the door into the receiver hole on the bottom main frame assembly.

Place the upper door hinge pin (E) through the hole in the main frame assembly and into the door frame assembly.
NOTE: Once the upper door hinge pin is installed it will not be removed easily.

Mounting of the Gate

Determine what side you wish to have the hinge of the door on. Place the wall mounts on that end of the gate against the wall. Using the wood screws (C), screw them into the wall.  Turning the a screwdriver in the clockwise direction will tighten the screws. Repeat on both ends of the gate.
NOTE: If your application does not require both extension gates, refer to removing the extension gate.

Tighten all the gate hinges by! wising the hinge knob counterclockwise direction.

Removing Extension Gate

If the standard gate is too long for your opening you must remove either the right or left extension gate. Loosen the hinge knob in the clockwise direction. Slide the hinge knob down and pull out the tube hinge. Do the same with the tube hinge on the end with the wall mounts.

Remove the hinge cover cap. The hinge cover cap is on the bottom of the hinge with the wall mounts. Remove the toothed hinge cap from the top.

Place the tube hinge, wall mounts, hinge knob, and cap hinge cover into the lower door frame. Place the toothed hinge cover on the top of the gate. Slide the hinge knob up into the toothed hinge cover and twist counter-clockwise to tighten. Once the hinge knob is tight lower the cap hinge cover all the way down.

Gate Operation

To open the gate, start by rotating the base lock in the upward direction. Do this on both sides of the door.
NOTE: You can rotate the base lock in either direction.

Press the release button down on the handle. Slide the handle back towards the hinge.
NOTE: The handle is spring-loaded and will return to its “locked” position on its own. When closing the gate you must do the same operation.

  WARNING

NOTE: The gap between the gate and wall should not exceed more than 2.5 inches.

• Install according to the manufacturer’s instructions.

• To prevent serious injury or death, securely install a gate or enclosure and use it according to the manufacturer’s instructions.

• Children have died or been seriously injured when gates are not securely installed. Always install and use as directed using all required parts.

• Never stack gates on top of each other to form a taller barrier.
  This could result in serious injury or death.

• Stop using it when a child can climb over or dislodge the gate.

• Use only the locking mechanism securely engaged.

• To prevent falls, never use at top of the stairs.

• Never use to keep the child away from the pool.

• Intended for use with children from 6 months through 24 months.

• Always ensure the gate is resting against the floor before beginning installation.

• This product will not necessarily prevent all accidents.
  Never leave a child unattended.

• Check the gate regularly to see if all the hardware and mountings are tightened.

• Do not use it if any component is missing or damaged.

• Adult assembly is required.

**www.regalo-baby.com
Regalo International, LLC.**
3200 Corporate Center Drive, Suite 100
Burnsville, MN 55306, USA
866.272.5274 (U.S. only) or 952.435.1080
20210811ET

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>