regalo 0370BR Arched Decor Safety Gate Instruction Manual

Arched Decor Safety Gate
Models: 0370BR, 0380BR

• READ ALL INSTRUCTIONS BEFORE ASSEMBLY AND USE OF GATE.
  KEEP INSTRUCTIONS FOR FUTURE USE.

Before Assembly

PLEASE CHECK TO MAKE SURE YOU HAVE THE FOLLOWING PARTS:

Left Side Frame Half (1)
Gate Door Panel (1)
Right Side Frame Half (1)
4″ Extension (1)
Threaded Spindle Rods (4)

Mounting Pin (1)
D| 4″ Extension (1)| I| Frame Assembly Screws (2)
E| Threaded Spindle Rods (4)| J| Hex Key (1)

BEFORE USING PRODUCT
Read and follow all instructions carefully to ensure that your gate and extensions are properly installed. Improper installation could result in the gate becoming unstable or dislodged from the
doorway. Always make sure the extension is securely attached to the gate before using. The safety of your child is your responsibility. Please keep these instructions for your reference.

IMPORTANT

• Never use more than two extensions per side of gate.
• If hardware mounting to a surface other than drywall or wood, please consult with a professional about installation.
• Base locks are to be used at all times, on both sides of the gate.

REMOVING YOUR GATE FROM THE WALL
To remove your gate from the wall, rotate the adjustment wheels on each of the (4) threaded spindle rods to depressurize the gate from its doorway or opening. Then, gently pull or push the gate free from its doorway or opening.

CARE AND MAINTENANCE
Periodically check the gate for signs of damage, wear, or missing components. Do not use if any part is missing, worn or damaged. Check the gate regularly to ensure all the hardware and mountings are tightened. Do not use abrasive cleaners or bleach. Clean by sponging with warm water and a mild detergent.

Assembling and Installing Your Gate

Take the left (A) and right (C) gate frame halves and align the holes in the lower horizontal tube. Place the frame halves together and then using the frame assembly screws (I), tighten the two halves together. Lower the gate door (B) into the assembled gate frame and insert the lower gate door pin into the mounting hole on the frame. Align the hole in the upper corner of the gate door with the hole in the door mounting bracket.
Insert the spring loaded mounting pin (H) into the hole in the mounting bracket and the door. Locate the (4) threaded spindle rods (E).
Rotate the adjustment wheels along the threading, eliminating the gap between the adjustment wheel and the rubber foot.
NOTE: You will notice a slight gap between the gate door latch and the frame tube. This is not a defect. Your gate is a pressure mounted gate and this gap will disappear once you tighten your gate in the doorway opening.

Insert the (4) threaded spindle rods into the holes at each of the four corners of the gate.
NOTE : Once the spring loaded mounting pin is inserted into the gate door hole, it cannot be taken out again by hand.
NOTE : It may be necessary to hold the threaded spindle rods or rubber feet while rotating the adjustment wheels to ensure the entire unit does not rotate. Position the gate so that it is level and centered within your doorway or opening. Rotate the adjustment wheels on the threaded spindle rods in the opposite direction as in Step 4, expanding the gap between the rubber foot and the adjustment wheel. Expand each of the (4) threaded spindle rods until they make contact with the doorway or opening. Do not fully tighten the threaded spindle rods yet.
NOTE : The gap between the gate and wall should not exceed more than 2.5 inches. Make the appropriate adjustment to ensure you have installed your gate safely.

When you are satisfied with the general placement of your gate, fully tighten the threaded spindle rods attached to the lower corners of the gate by further rotating the adjustment wheels. Continue by tightening the upper threaded spindle rods. As you tighten the threaded spindle rods, you will notice the gap between the door frame and the arched handle latch begin to narrow. In order for the gate to function properly, stop tightening the upper threaded spindle rods just before the outer housing of the arched handle latch and the receiving component touch.
NOTE : There should be equal spacing among each of the (4) threaded spindle rods. Make the appropriate adjustment to ensure you have installed your gate safely.

Operating the Door Latch

Pull up on the lower trigger while simultaneously pulling back on the top slider button. These two actions combined will  disengage the lock and allow the gate to open freely.
Push or pull to open the gate door. To close, simply push or pull the door back into its original position. The arched handle latch will re-engage automatically and lock the door into its closed position.
NOTE : If your arched handle latch is not properly engaging with the receiving component, ensure that your gate is level, mounted properly, and that you have not over-tightened the threaded spindle rods. At the bottom of the gate door, rotate the base lock to the horizontal position. To allow the door to swing open in only one direction rotate the base lock on one side.
To allow the door to swing open in both directions, rotate the base lock on both sides.
NOTE : Place lock down on side occupied by the child.

Positioning and Attaching Wall Cups

After you have mounted your gate, and you are satisfied with its positioning, draw a circle on the surface of your doorway or opening around the perimeter of the (4) rubber feet.
Next, completely remove the gate from the opening by loosening each of the (4) threaded spindle rods to depressurize the gate.With gate fully removed, you can now use the circles you marked during Step 1 as guides for screwing in your (4) wall cups. Center each of the wall cups within the guide circles and use the provided self-tapping screws (G) to fasten them in place via the hole
through the center of each wall cup.Reinstall your gate in the doorway or opening according to the instructions, using the newly installed wall cups as anchoring points for the (4) threaded spindle rods.

Adding a Gate Extension

Remove the top and bottom threaded spindle rods.
Assemble the gate and extension as illustrated. Reposition the gate and fit in accordance with the gate fitting.
NOTE : It is preferable to install any extensions on the hinge side of the gate.

Replacement Parts

A Hardware Kit #11055 Includes:
Threaded Spindle Rods w/ Adjustment Wheel (4), Spring Loaded Upper Door Mounting Pin (1), 1” Wall Mount Screws (4), Frame Assembly Screw (2), Wall Cups (4), Hex Key (1)

90 DAYS LIMITED WARRANTY
If, during the first 90 days after consumer purchase of the item, under reasonable and non-commercial use and conditions of maintenance, it fails while owned by the original purchaser because of the quality of materials or workmanship of finish and assembly, Regalo International, LLC, will replace or repair it at Regalo’s option. PROOF OF PURCHASE REQUIRED.

Need more width? Additional extensions sold separately
www.regalo-baby.com

0370 EXTENSIONS

• 4″ Extension
  Bronze = #1074 BR

• 6″ Extension
  Bronze = #1076 BR

0380 EXTENSIONS

• 4″ Extension
  Bronze = #1084 BR

• 6″ Extension
  Bronze = #1086 BR

WARNING MISE EN GARDE ADVERTENCIA

The gap between the gate and wall should not exceed more than 2.5 inches.
NOTE : When installing any gate at its maximum width, use wall cups to ensure stability and safety.

• Install according to manufacturer’s instructions.

• To prevent serious injury or death, securely install gate or enclosure and use according to manufacturer’s instructions.

• Children have died or been seriously injured when gates are not securely installed. ALWAYS install and use as directed using all required parts.

• Never stack gates on top of each other to form a taller barrier. This could result in serious injury or
  death.

• STOP using when a child can climb over or dislodge the gate.

• Use only with the locking mechanism securely engaged.

• To prevent falls, NEVER use at top of stairs.

• NEVER use to keep child away from pool.

• Intended for use with children from 6 months through 24 months.

• Always ensure the gate is resting against the floor before beginning installation.

• This product will not necessarily prevent all accidents. Never leave child unattended.

• Check the gate regularly to see if all the hardware and mountings are tightened.

• Do not use if any component is missing or damaged.

• Adult assembly required.

www.regalo-baby.com
Regalo International, LLC.
3200 Corporate Center Drive, Suite 100  866.272.5274 (U.S. only
Made in China

Documents / Resources

| regalo 0370BR Arched Decor Safety Gate [pdf] Instruction Manual
0370, 0380, 0370BR, 0370BR Arched Decor Safety Gate, Arched Decor Safety Gate, Decor Safety Gate, Safety Gate, Gate
---|---

References

• Regalo Baby

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>