PARKSIDE 2 X 50W LED Work Light Instructions

PARKSIDE 2 X 50W LED Work

List of pictograms used
2 x 50 W LED work light

Introduction

We congratulate you on the purchase of your new product. You have chosen a high-quality product. The instructions for use are part of the product. They contain important information concerning safety, use, and disposal. Before using the product, please familiarise yourself with all of the safety information and instructions for use. Only use the product as described and for the specified applications. If you pass the product on to anyone else, please ensure that you also pass on all the documentation with it.

Intended use

This lamp is suitable for indoor and outdoor use. This product is only intended for private household use. Any other use or product modification is prohibited and will result in damage. The manufacturer does not assume any liability for damage arising from improper use. The product is not intended for com-mercial use.

Scope of delivery

Always check that all the parts are present and that the product is in perfect condition immediately after unpacking.

1.  handle piece
2.  spotlights
3.  clamping nuts with 3 washers each (mounting bracket) (pre-installed)
4.  mounting bracket
5.  screws with 2 washers (mounting bracket) (pre-installed)
6.  tripod
7.  clamping nut (tripod) (pre-installed)1
8. screw (handle) (pre-installed)
9.  set of assembly instructions and instructions for use

Parts description

1.  Handle piece
2.  Spotlight
3.  Wing bolt
4.  Clamping nut (mounting bracket) 5 Mounting bracket
5.  Screw (mounting bracket)
6.  Clamp
7.  Height adjuster
8.  Tripod
9.  Cable winder
10.  Clamping nut (tripod)
11.  Screw (handle)
12.  Mains cable bracket
13.  Socket
14. Mains cable
15. ON / OFF switch

Technical data

• Model number: Operating voltage: Total output:
• IP rating: Dimensions per floodlight:
• Height of tripod
• including spotlight: Cable length: Light color: Total luminous flux:
• Adjustable beam angle: 105 °Luminous flux at
• 120 ° angle: Weight: Projected area:
• FCL-80121
• 220–240 V∼ 50 Hz
• 2 x 50 W
• IP54
• approx. 18.2 cm x 14.6 cm x 5.4 cm (L x H x D)
• 115–165 cm
• 5 m
• 6500 K
• 2 x 4500 lm, Ra > 80
• approx. 2 x 4000 Im 6 kg
• approx. 7 m x 7 m
• 220–240 V∼ 50 Hz max. 3580 W IP54

Safety notes

DANGER TO LIFE AND RISK OF ACCIDENTS FOR INFANTS AND CHILDREN! This product may be used by children aged 8 years and up, as well as by persons with reduced physical, sensory or mental capacities or lacking experience and knowledge, so long as they are supervised or instructed in the safe use of the product and understand the associated risks. Do not allow children to play with the product. Cleaning and user maintenance must not be performed by children without supervision. Do not leave the lamp or packaging material lying unattended. Plastic films/bags, plastic parts, etc. are dangerous for children to play with. The maximum installation height must not exceed 5 meters.

AVOID THE RISK OF FATAL INJURY FROM ELECTRIC SHOCK

• We assume no liability for property damage or personal injury caused by improper handling or failure to observe the safety notices!
• Never use the lamp if any defects have been identified. Check the light and the main cable 15 with the plug for any damage before connecting it to the mains.
• Never open any of the electrical equipment or insert objects into these. Such interferences pose a risk of fatal injury from electric shock.
• Only touch the insulated part of the mains plug when connecting or disconnecting it from the mains supply!
• To avoid hazards, if the flexible lead on this light is damaged it must be replaced by the manufacturer, their service representatives or an equivalent professional!
• Before use, verify that the available mains volt-age matches the required operating voltage of the lamp (220–240 V∼, 50 Hz).
• Under no circumstances should you allow liquids or steam to enter the socket on the back! This can cause it to short circuit and pose a risk of death or serious injury.
• Only use IPX4 plugs in the socket.
• When using the built-in socket, the IP protection is reduced to IP44 if a corresponding IP44 model plug is used.
• Disconnect the product from the mains supply whenever you want to use it in a different location.
• Never carry the product by the main cable. Only use the handle piece to adjust the lamp, not to carry it.
• Do not connect the product in series.
• Do not cover the lamp with objects. Excessive heat build-up can result in fire.
• Never leave the lamp unattended during oper-ation. Excessive heat build-up can result in fire. The LED lamp is not dimmable.
• Do not look directly into the light source (light bulb, LED etc.). Do not look into the light source (light bulb, LED, etc.) with an optical instrument (e.g. magnifying glass).
• A shattered protective covering must always be replaced.

Installation

DANGER OF ELECTRIC SHOCK! Only insert the mains plug into the mains socket after it has been assembled. Otherwise, there is a risk of electric shock!
Note: You can use the light as a handheld or floor spotlight or with the tripod 9 if necessary.

Assembling the spotlights and handle piece on the mounting bracket
First, unscrew the pre-installed fixing material (screws 6 , clamping nuts 4 and the washers pertaining to them) from the mounting bracket 5 (see Fig. A, ensure that the washers are in the correct order). Screw both spotlights 2 with the clamping nut 4 and the washers to the mounting bracket 5 (see Fig. B, ensure that the washers are in the correct order). Screw the handle piece 1 with the screws 6 and the washers to the mounting bracket 5 (see Fig. C, ensure that the washers are in the correct order). Loosen screw 12 on the reverse side of the handle piece 1 and attach the mains cable bracket 13 to the handle piece 1 (see Fig. D).

Setting up the tripod
Loosen the clamping nut 11 by turning it anticlockwise (see Fig. E).
Catch the tripod element where the legs are connected at the same height as the clamping nut 11 and press it downwards so that the legs unfold. When the tripod element cannot be pushed down any further, and the legs have fully folded out, re-tighten by turning the clamping nut 11 clockwise (see Fig. F).

Setting the tripod height
(see Fig. G) Loosen the height adjuster 8 by turning it anticlockwise. Set the tripod 9 at the desired height by pulling the rod elements upwards or pushing them downwards. Tighten the height adjuster 8 by turning it clockwise to fix the tripod 9 at the desired height.

Assembling the work light on the tripod

Note: To assemble the work light on tripod 9 you must first assemble the spotlights 2 and the handle piece 1 on the mounting bracket 5 . Proceed as described in the chapter “Assembling the spotlights and handle piece on the mounting bracket”.

1. Place the mounting bracket 5 (with spotlights 2 and handle piece 1 ) on the open clamp 7 .
2. The handle piece 1 must be orientated in the direction of the retaining plates on clamp 7 , as otherwise, it cannot be fixed.
3. Also, ensure that you place the holes on the underside of the mounting bracket 5 on the pins of clamp 7 (see Fig. HI and HII)
4.  Close the retaining plate of the clamp 7 (see Fig. HIII).
5. Flip the clip of the clamp upwards, so that it catches in the retaining plate (see Fig. HIV).

Disassembling the work light
DANGER OF ELECTRIC SHOCK! Remove the mains plug from the mains socket before disassembly. CAUTION! RISK OF BURNS DUE TO HOT SURFACES! Allow the light to cool down fully before disassembling it.
To disassemble the individual elements, proceed in the reverse order as described in the respective chapters.

Operation

• Using the light (see Fig. I)
• Completely unwind the mains cable 15. Connect the mains plug to the mains socket. You can switch the light of any of the spotlights
•  on and off by pressing the ON / OFF switch 16 on the back.
• P osition I: 50 % light, 2250 Lumen (both spotlights together 4500 Lumen)
• Position II : 100 % light, 4500 Lumen (both spotlights together 9000 Lumen)
• Position 0: Off
• Loosen the wing bolt 3 to tilt the spotlight 2 into the desired position. Re-tighten the wing bolt
•  to fix the spotlight 2 in the desired position. Using the socket Before using socket 14 ensure that the maximum nominal load of 3580 W is NOT exceeded by the connected device.
• The socket 14 on the back of the spotlight is always active when the mains plug of the product is in the wall socket.
• To use socket 14 on the back of the spot-light, flip the socket cover-up and connect the desired device.

Maintenance and cleaning

DANGER OF ELECTRIC SHOCK! Before cleaning the light, remove the mains plug from the mains socket and wind the mains cable 15 on the cable winder 10 .  To ensure electrical safety, never clean the light with aggressive detergents or immerse it in water.  RISK OF BURNS DUE TO HOT SURFACES! Allow the spotlights 2 to cool down completely. Do not use solvents, petrol, etc. These would damage the light. Only use a dry, lint-free cloth for cleaning. Use a slightly moist cloth to remove any stubborn dirt.

Disposal

The packaging is made entirely of recyclable mate-rials, which you may dispose of at local recycling facilities.

1. Observe the marking of the packaging materials for waste separation, which are marked with abbreviations (a) and numbers (b) with the following meaning: 1–7: plastics / 20–22: paper and fiber-board / 80–98: composite materials.
2. The product and packaging materials are recyclable, dispose of it separately for better waste treatment. The Triman logo is valid in France only.
3. Contact your local refuse disposal authority for more details of how to dispose of your worn-out product.
4. To help protect the environment, please dispose of the product properly when it has reached the end of its useful life and not in the household waste. Information on collection points and their opening hours can be obtained from your local authority.

Warranty and service

Warranty

• The product has been manufactured to strict quality guidelines and meticulously examined before delivery. In the event of product defects, you have legal rights against the retailer of this product. Your legal rights are not limited in any way by our warranty detailed below.
• The warranty for this product is 3 years from the date of purchase. The warranty period begins on the date of purchase. Please keep the original sales receipt in a safe location. This document is required as your proof of purchase.
• Should this product show any fault in materials or manufacture within 3 years from the date of purchase, we will repair or replace it – at our choice – free of charge to you. This warranty becomes void if the product has been damaged, or used or maintained improperly.
• The warranty applies to defects in material or manufacture. This warranty does not cover product parts subject to normal wear, thus possibly considered consumables (e.g. batteries) or for damage to fragile parts, e.g. switches, rechargeable batteries or glass parts.

Service address

Teknihall Elektronik GmbH Breitefeld 15 64839 Münster GERMANY 00800 333 00 888 smartwares-service-uk@teknihall.com smartwares-service-ie@teknihall.com Toll-free number

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>