Amico Hummingbird Lite LCD-AIO Tablet and Electric Lift with Smart Drawer Instruction Manual
- June 6, 2024
- Amico
Table of Contents
Quick Installation and Maintenance Instructions
Hummingbird Lite
Medical Facility Responsibility
Preventive maintenance checks must be performed regularly to maintain the quality and performance of this product. Any parts that may be broken, missing, worn, distorted, or contaminated in any way should not be used and all affected parts should be replaced immediately. Should the necessity of any repair be suspected; please contact your local distributor.
WARNING: It is the responsibility of the end user to ensure all aspects of installation are covered by following the full manual and reviewing warnings/notes found at:http://www.amico.com/products/computer- workstations/mobile/non-powered/hummingbird-lite-laptop.
NOTE: An assembly walk-through video is also available here:
| http://www.amico.com/qr-code/redirect/hummingbird-lite-laptop-assembly-
instructions/
---|---
Installation Tools
Installation Reference
**Hardware Kit:
**
A hardware kit for each component can be found taped to the component (e.g. hardware kit to secure base to column is found taped to the base).
Instructions:
-
.Unpack the master box. The sequence in which contents are packed is indicated on the master box.
-
Place wheelbase with casters on the ground (Figure 2). Secure in place by engaging the brakes on the front casters.
-
Join the column (Box B) with base by sliding the column into the opening on top of the base (Figure 3) and fasten four 1/4-20 x 1″ long screws, four #14 lock washer, and four #14 flat washer through the bottom of the base into the column (mounting kit taped inside base). Ensure the bottom of the vertical column is placed inside the collar (pre-installed in opening). You might find it easier to do this step with the base on its side – use the column box to support the column if necessary.
-
Place the worktop (Master Box) on the column top plate and fasten four 1/4-20 x 3/8″ long screws (hardware kit taped to top of column) (Figure 4). Fit the lever housing to the worktop with four 1/4-20 x 1/2″ long screws (hardware kit taped to lever housing) (Figure 5).
I. Laptop Security Bracket Models: Install the Laptop Security Bracket (Box C) to the worktop by placing the Laptop Security Bracket on the back of the worktop and fasten four 1/4-20 x 1/4″ long screws (mounting kit taped to bracket) (Figure 6) from the bottom.
II. LCD/Display Post Models: To attach the LCD/Display Post (Box C) to the worktop, first place the bracket (Box C) to the worktop bottom and fasten four 1/4-20 x 1/4″ long screws (Figure 7) from the bottom (hardware kit taped to bracket). Carefully insert the LCD/Display Post through the worktop opening on the top and align with the bracket hole. Fasten with four 8-32 x 9/16″ long screws (ardware kit taped to LCD/Display Post)
III. Sliding Keyboard Tray Models: Slide the keyboard tray bracket (Box C) into the worktop keyboard tray track (Figure 8) and insert 10-24 x 1/2″ long screws through spacer/stopper into keyboard tray track to secure. Remove the bottom acorn nuts and #10 washers from the Sliding Keyboard Tray (Master Box) and align with keyboard tray bracket holes. Fasten back #10 washer and acorn nuts (Figure 8).
- Attaching Accessories
II. POWER CORD HOOK / POWER CORD + BARCODE SCANNER HOOK Install the hook (Box C) to the worktop bottom plate with two 8-32 x 3/16″ long screws (hardware kit taped to hook) (Figure 9).
II. POWER SUPPLY / POWER BAR: The cart has zip tie saddles on the left and right underneath the worktop for securing power supplies or power bars. Slide a zip tie (found with worktop) through each saddle slots (Figure 10). Place the power bar or power supply within the two zip ties and secure.
Product Matrix
Specifications and Adjustments
Refer to Amico website for the manual and specification documents.
Troubleshooting Guide
| Problem | Possible Cause | Solution |
|---|---|---|
| LCD mount facing wrong direction | Incorrect installation | Check the |
LCD/Display Post hole positions, should keep the LCD mounting facing front
with 180° hole pattern
Loosened worktop| Improper installation or loose connection| Check the screws
between worktop and column plate, should be tightly secured
Sliding Keyboard Tray falls off| Forgot to install the stopper| Make sure
always stopper is installed
Laptop adjustable clamp is not opening| Missing key| Locate the key or contact
Amico
Too easy or too difficult to utilize the portrait landscape feature| Damaged
hardware| Please contact Amico Accessories
The display mount is not secure, it is wobbling or loose when using the
portrait landscape feature| Damaged display mount| Display mount needs to be
replaced. Please contact Amico Accessories
Monitor drifts down| Incorrect gas spring in LCD/Display Post| Please contact
Amico Accessories
Maintenance
It is recommended that once every three (3) months, all locks, bolts and screws are visually inspected for signs of product wear and tear or damage. Check the product for looseness in the mount or orientation, and ensure the adapter is secure.
Warranty
During the term of warranty: Within the first twelve (12) months from the date
of shipment, Amico Accessories will repair or replace any part which is proven
to be defective at no cost. After the twelve (12) month period, Amico
Accessories will send the parts to the customer free of charge, however
shipping and installation will be borne by the customer.
Amico Accessories Inc. will warrant its materials to be free from defect for
an additional period of four (4) years, (five [5] years from the date of
shipment). Within this period, Amico Accessories Inc. will replace any part
which is proven to be defective, at no charge. Shipping and Installation costs
after the first twelve (12) months will be borne by the Customer.
The warranty is valid only when the product has been properly installed
according to Amico Accessories specifications, used in a normal manner, and
serviced according to factory recommendations. It does not cover failures due
to damage that occur in shipments or failures which resulted from accidents,
misuse, abuse, neglect, mishandling, alteration, misapplication or damage that
may be attributable to Force Majeure.
Amico Accessories Inc. shall not be liable for incidental or consequential
damages resulting from use of equipment.
All claims for warranty must first be approved by Amico Accessories Inc. A
valid Return Goods Authorization (RGA) number must be obtained from Amico
Accessories Inc. prior to commencement of any service work. Warranty work,
which has not been preauthorized by Amico Accessories Inc., will not be
reimbursed.
AMICO ACCESSORIES DOES NOT HONOR VERBAL STATEMENTS CONCERNING THE
WARRANTY.
The distributor and/or dealer are not sanctioned to create verbal warranties
about the product described in this agreement. Any statements will not be
honored or be made part of the agreement of sale. This document is the final
complete and exclusive terms of the agreement.
THIS WARRANTY IS INCLUSIVE AND REPLACES ALL OTHER WARRANTIES.
Amico Accessories shall not, under any circumstances be liable for incidental
or consequential damages including, but not limited to, profit, loss of sales
or injuries to person(s) or property.
Correction of non-compliance as noted above will result in completion of all
liabilities of Amico Accessories whether based on agreement, neglect or
changed materials, designs or specifications without notice.
All claims for warranty must first be approved by Amico Accessories Inc.
Service Department: accessories@amico.com or 1.877.264.2697. A valid Return
Goods Authorization number must be obtained from Amico Accessories Inc. prior
to commencement of any warranty claim.
Amico Accessories Inc. 122 East Beaver Creek Road, Richmond Hill, ON L4B 1G6,
Canada
Toll Free Tel: 1.877.264.2697 | Tel: 905.763.7778 | Fax: 905.763.8587
AMICO-AA-HUMMINGBIRD-LITE-QUICK-INSTALLATION-MANUAL 04.23.2021
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>