Amico BARCHLD2 Barcode Dock Mount Installation Guide
- May 15, 2024
- Amico
Table of Contents
Barcode Dock Mount – BARCHLD2
Quick Installation and Maintenance Instructions
BARCDHLD2-(M/F/A/E25/R125/RMC/V/D/G/S/LCD)
Medical Facility Responsibility
Preventive maintenance checks must be performed regularly to maintain the
quality and performance of this product. Any parts that may be broken,
missing, worn, distorted or contaminated in any way should not be used and all
affected parts should be replaced immediately. Should the necessity of any
repair be suspected; please contact your local Amico distributor.
WARNING: This Quick Installation Guide is not a replacement for the full
manual. It is the responsibility of the end user to ensure all aspects of the
installation are covered by following the full manual and reviewing
warnings/notes found at: https://docs.amico.com/amico-aa-barcode-dock-
mounts-manual.pdf.
Installation Tool
Installation Reference
Pre-installation Information
Determine the preferred orientation of the barcode charging base and refer to the below illustrations for mounting. Note the illustrations shown may not portray the configuration purchased. Use this guide as a reference to pair hardware and mounting hole pattern with respective barcode scanner base (not provided).
Barcode charging base with 1 hole, such as Honeywell 2020 for barcode scanners: 3820, 4620, 4820, or 5620
Barcode charging base with 2 holes, such as Honeywell CCB01-010BT for the
Honeywell Xenon 1900, 1910, 1902, 1912
Barcode charging base with 4 holes, such as code reader CRA-A101 or CRA-A104
for CR2600
Installation to Device
- Before mounting the barcode scanner onto the mounting plate, determine the mounting pattern on the barcode scanner base. If the barcode scanner base is too larger to mount onto the BARCODE SCANNER HOLDER, proceed to step 2 for installation of secondary plate.
If the secondary extension plate is required, determine the preferred orientation (refer to section 2: Pre-installation Instructions) and secure by inserting 2x or 3x H-FHMS-832-12 through the EXTENSION PLATE, BARCODE SCANNER HOLDER, 2x or 3x STEEL LOCK WASHERS, 2x or 3x ACORN NUTS, ensuring that the MOUNTING SCREWS do not interfere with the mounting pattern of the BARCODE SCANNER BASE.
Installation to LCD
-
Slide the LCD SHELF ARM to desired position and tighten 2x HEX NUTS. Insert and tighten 2x NYLON LOCK NUTS to lock the LCD SHELF ARM in place. Cover the exposed NUTS with 2x HEX BOLT NUTS AND CAPS.
-
Loosely insert 2x 16 mm PANHEAD SCREWS through the top of two holes of the MONITOR HANDLE BODY and into the MONITOR (not provided). If the mounting pattern is recessed in the MONITOR, place 4x NYLON STANDOFFS between the MONITOR HANDLE BODY and the MONITOR, and use the 20mm MACHINE SCREW instead of the 16 mm PANHEAD SCREW.
-
Slide 2x 12mm PANHEAD SCREWS into the U-NOTCHES on the LCD VESA PLATE (not provided).
Insert another 2x 72 mm PANHEAD SCREWS into the 2x BOTTOM HOLES of the LCD VESA PLATE, MONITOR HANDLE BODY, and into the MONITOR. -
Tighten 4x 12mm PANHEAD SCREWS in a cross pattern.
Adjustments (For LCD)
To adjust the BARCDHLD2-LCD, remove 2x HEX BOLT NUTS AND CAPS, 2x NYLON LOCK
NUTS and loosen 2x HEX NUTS.
Slide LCD SHELF ARM to the desired location and re-tighten 2x HEX NUTS and 2x
NYLON LOCK NUTS.
WARNING: In AHM ARM(s) with extensions, both arms have a 180° rotation.
Ensure proper clearance around the arm(s) to avoid collision.
Troubleshooting Guide
| Symptom | Possible Cause | Solution |
|---|---|---|
| Scanner base appears tilted/not centered. | Loose mounting configuration or | |
| device has shifted. | Re-center mounting brackets and refer to instructions |
(Pre-installation and Installation to Device)
Mounting bracket is shifting.| Improper installation to mounting platform.|
Ensure device is secured to rail or mounting platform.
Refer to instructions (Installation to Mounting Platform).
Maintenance
It is recommended that once every one (1) month, all locks, bolts, and screws
are visually inspected for signs of product wear and tear or damage.
Check the product for looseness in the mount or orientation, and ensure the
adapter is secured to the rail or wall channel system.
Warranty
During the term of warranty: Within the first twelve (12) months from the date
of shipment, Amico Accessories will repair or replace any part which is proven
to be defective at no cost. After the twelve (12) month period, Amico
Accessories will send the parts to the customer free of charge, however
shipping and installation will be borne by the customer.
The warranty is valid only when the product has been properly installed
according to Amico Accessories specifications, used in a normal manner, and
serviced according to factory recommendations. It does not cover failures due
to damage which occur in shipments or failures which resulted from accidents,
misuse, abuse, neglect, mishandling, alteration, misapplication or damage that
may be attributable to Force Majeure.
AMICO ACCESSORIES DOES NOT HONOR VERBAL STATEMENTS CONCERNING THE WARRANTY.
The distributor and/or dealer are not sanctioned to create verbal warranties
about the product described in this agreement. Any statements will not be
honored or be made part of the agreement of sale. This document is the final
complete and exclusive terms of the agreement.
THIS WARRANTY IS INCLUSIVE AND REPLACES ALL OTHER WARRANTIES.
Amico Accessories shall not, under any circumstances be liable for incidental
or consequential damages including, but not limited to, profit, loss of sales
or injuries to person(s) or property.
Correction of non-compliance as noted above will result in completion of all
liabilities of Amico Accessories whether based on agreement, neglect or
changed materials, designs or specifications without notice.
All claims for warranty must first be approved by Amico Accessories Customer
Service Department: (info@amico-accessories.com or 1-877-264-2697).
A valid Return Goods Authorization number must be obtained from Amico
Accessories prior to commencement of any warranty claim.
Amico Accessories Inc. | 85 Fulton Way, Richmond Hill, ON L4B 2N4, Canada |
www.amico.com
Toll Free Tel: 1.877.264.2697 | Tel: 905.763.7778 | Fax: 905.763.8587 | Email:
info@amico-accessories.com
AA-QG-BARCODE-DOCK-MOUNT 02.27.2024
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>