GOLD MEDAL 2705 Mini Cheese Corn Tumbler Instruction Manual
- June 6, 2024
- GOLD MEDAL
Table of Contents
- GOLD MEDAL 2705 Mini Cheese Corn Tumbler
- SAFETY PRECAUTIONS
- INSTALLATION INSTRUCTIONS
- OPERATING INSTRUCTIONS
- Care and Cleaning
- MAINTENANCE INSTRUCTIONS
- Ordering Spare Parts
- Parts – Mini Cheese Corn Tumbler
- Electrical Schematic – 2705 and 2705EX
- WARRANTY
- References
- Read User Manual Online (PDF format)
- Download This Manual (PDF format)
GOLD MEDAL 2705 Mini Cheese Corn Tumbler
SAFETY PRECAUTIONS
DANGER
Machine must be properly grounded to prevent electrical shock to personnel.
Failure to do so could result in serious injury, or death.
Make sure all machine switches are in the OFF position before plugging the
equipment into the receptacle. Keep cord and plug off the ground and away from
moisture. Always unplug the equipment before cleaning or servicing. DO NOT
immerse any part of this equipment in water.
DO NOT use a water jet or excessive water when cleaning.
WARNING
ALWAYS wear safety glasses when servicing this equipment.
WARNING
No user serviceable parts inside. Refer servicing to qualified service
personnel.
WARNING
Read and understand operator’s manual and all other safety instructions before
using this equipment. To order copies of the operator’s manual go to
gmpopcorn.com or write to Gold Medal Products Co., 10700 Medallion Drive,
Cincinnati, OH 45241 USA 1-(800)-543-0862
WARNING
DO NOT allow direct contact of this equipment by the public when used in food
service locations. Only personnel trained and experienced in the equipment
operation may operate this equipment.
Carefully read all instructions before operation.
WARNING
This machine is NOT to be operated by minors.
DO NOT install equipment in an area where a water jet is used.
This appliance is not intended for use by persons (including children) with
reduced physical, sensory or mental capabilities, or lack of experience and
knowledge, unless they have been given supervision or instruction concerning
use of the appliance by a person responsible for their safety.
Unit to be in a supervised location.
Install unit on a level surface. Locate machine in a protected environment.
Note: Improvements are always being made to Gold Medal’s equipment. This
information may not be the latest available for your purposes. It is critical
that you call Gold Medal’s Technical Service Department at
1-800-543-0862 for any questions about
your machine operations, replacement parts, or any service questions. (Gold
Medal Products Co. does not assume any liability for injury due to careless
handling and/or reckless operation of this equipment.) General images may be
used in manual for reference only.
INSTALLATION INSTRUCTIONS
Inspection of Shipment:
After unpacking, check thoroughly for any damage which may have occurred in transit. Claims should be filed immediately with the transportation company. The warranty does not cover damage that occurs in transit, or damage caused by abuse, or consequential damage due to the operation of this machine, since it is beyond our control (reference warranty in back of manual).
Manual
Read and understand the operator’s manual and all other safety instructions before using this equipment. To order copies of the operator’s manual go to gmpopcorn.com or write to Gold Medal Products Co., 10700 Medallion Drive, Cincinnati, OH 45241 USA 1-(800)-543-0862.
Model Description
- 2705: Mini Cheese Corn Tumbler with stainless steel base and a plastic tub
- 2705EX: Export Mini Cheese Corn Tumbler with stainless steel base and a plastic tub
Setup
This unit has been tested at the factory.
-
Remove all packaging and tape prior to operation.
-
Attach the drive bar to the motor shaft with the set screw provided using a 3/32” hex key (see image below)—set screw fastens against the flat of the motor shaft.
The drive bar hole should be flush with the tip of the motor shaft and tightly secured into position. -
After setup, the unit should be cleaned prior to use (see Care and Cleaning section)
Electrical Requirements
The following power supply must be provided (reference unit Data Plate for Wattage requirement):
- 2705: 120 V~, 60 Hz
- 2705EX: 220-230 V~, 50/60 Hz
- Potential Electrical Variations: 220 V~, 60 Hz
DANGER
Machine must be properly grounded to prevent electrical shock to personnel.
Failure to do so could result in serious injury, or death.
Make sure all machine switches are in the OFF position before plugging the
equipment into the receptacle. Keep cord and plug off the ground and away from
moisture. Always unplug the equipment before cleaning or servicing.
DO NOT immerse any part of this equipment in water.
DO NOT use a water jet or excessive water when cleaning.
A certified electrician must furnish sufficient power for proper machine operation and install any supplied receptacle (reference unit Data Plate for model specific Volts AC, Hertz, and Wattage requirements). We recommend this equipment be on a dedicated and protected circuit. Failure to wire properly will void the warranty and may result in damage to the machine. It is Gold Medal Products Co.’s recommendation that this machine be plugged directly into a wall outlet. The use of extension cords is not recommended due to safety concerns, and may cause sacrificed and/or reduced performance. Make sure cord is located to prevent a trip hazard or unit upset.
Before You Plug In Machine
- Make sure all machine switches are OFF before plugging equipment into receptacle.
- Make sure wall outlet can accept the grounded plugs (where applicable) on the power supply cord.
- The wall outlet must have the proper polarity. If in doubt, have a competent electrician inspect the outlet and correct if necessary.
- DO NOT use a grounded to un-grounded receptacle adapter (where applicable).
- Install unit in a level position.
CAUTION
If the supply cord is damaged, it must be replaced by Gold Medal Products Co., its service agent or similarly qualified persons in order to avoid a hazard.
OPERATING INSTRUCTIONS
Controls and Their Functions
Motor Switch – With the rocker switch in the “ON” position, the roller motor will run continuously.
Operating
The Mini Cheese Corn Tumbler has a tub capacity of 2.5 gallons without the lid
and 4.5 gallons with the lid.
- Place the tub into the drive bar and onto the rollers securely (reference Setup section to install drive bar).
- Add material to be mixed and place the lid cover onto the tub.
- Turn the motor switch “ON” and begin tumbling material.
- For cheese corn, begin adding cheese mixture until the corn is coated as desired.
- Turn the motor switch “OFF”.
- Remove the tub and empty the contents.
- Repeat the process for additional product.
Care and Cleaning
DANGER
Machine must be properly grounded to prevent electrical shock to personnel. DO
NOT immerse in water. DO NOT clean appliance with a water jet. Always unplug
the equipment before cleaning or servicing.
Good sanitation practice demands that all food preparation equipment be
cleaned regularly (only use non-toxic, food grade cleaners). A clean looking,
well-kept machine is one of the best ways of advertising your product.
Follow the directions below to clean and sanitize unit each day after use.
-
Turn machine OFF, unplug unit before attempting to clean.
-
Wipe stainless steel parts with a clean cloth and cleaner designed for stainless steel, such as Gold Medal Watchdog Stainless Cleaner (Item No. 2088).
DO NOT use oven cleaners or abrasive materials as they will damage parts of machine. -
The mixing tub can be taken to a sink to clean with soap and water, then rinse and dry.
THE FOLLOWING SECTIONS ARE FOR QUALIFIED SERVICE PERSONNEL ONLY
MAINTENANCE INSTRUCTIONS
DANGER
Machine must be properly grounded to prevent electrical shock to personnel.
Failure to do so could result in serious injury, or death.
Make sure all machine switches are in the OFF position before plugging the
equipment into the receptacle. Keep cord and plug off the ground and away from
moisture. Always unplug the equipment before cleaning or servicing.
DO NOT immerse any part of this equipment in water.
DO NOT use a water jet or excessive water when cleaning.
DANGER
Improper installation, adjustment, alteration, service, or maintenance can
cause property damage, injury, or death. Any alterations to this equipment
will void the warranty and may cause a dangerous condition. This appliance is
not intended to be operated by means of an external timer or separate remote-
control system. NEVER make alterations to this equipment. Read the
Installation, Operating, and Maintenance Instructions thoroughly before
installing, servicing, or operating this equipment.
WARNING
No user serviceable parts inside. Refer servicing to qualified service
personnel.
CAUTION
THE FOLLOWING SECTIONS OF THIS MANUAL ARE INTENDED ONLY FOR QUALIFIED SERVICE
PERSONNEL WHO ARE FAMILIAR WITH ELECTRICAL EQUIPMENT. THESE ARE NOT INTENDED
FOR THE OPERATOR.
Ordering Spare Parts
- Identify the needed part by checking it against the photos, illustrations, and/or parts list. (General images may be used in manual for reference only.)
- Use only approved replacement parts when servicing this unit.
- When ordering, please include part number, part name, and quantity needed.
- Please include your model number, serial number, and date of manufacture (located on the machine nameplate/data plate) with your order.
- Address all parts orders to: Parts Department Gold Medal Products Co. 10700 Medallion Drive Cincinnati, Ohio 45241-4807 Or, place orders by phone or online:
Phone: 800-543-0862 513-769-7676
Fax: 800-542-1496 513-769-8500
E-mail: info@gmpopcorn.com
Web Page: gmpopcorn.com
Parts – Mini Cheese Corn Tumbler
CAUTION: If supply cord is damaged, it must be replaced by Gold Medal Products Co., its service agent, or similarly qualified persons in order to avoid a hazard.
Item | Part No. | Description |
---|---|---|
1 | 49656 | Glide 1″ (x2) |
2 | 89129 | Hex Nut #8-32 (x2) |
3 | 18710 | Drive Bar Assembly |
4 | 17543 | Tumbler Base |
5 | 87163 | Strain Relief |
6 | 22038 | Lead-In Cord, 15 amp (Domestic) |
42369 | Power Supply Cord (Export) | |
7 | 49045 | Motor 120V (Domestic) |
49045EX | Motor 230V (Export) | |
8 | 42532 | Switch, DPST Rocker |
9 | 17544 | Motor Cover |
10 | 17542 | Plastic Tub |
11 | 17547 | Lid (Not Pictured) |
Electrical Schematic – 2705 and 2705EX
WARRANTY
Gold Medal Products Co. warrants to the original purchaser each item of its
manufacture to be free of defects in workmanship and material under normal use
and service. Gold Medal Products Co.’s obligation under this warranty is
limited solely to repairing or replacing parts, f.o.b. Cincinnati, Ohio, which
in its judgment are defective in workmanship or material and which are
returned, freight prepaid, to its Cincinnati, Ohio factory or other designated
point. Except for “Perishable Parts” on specific machines, the above warranty
applies for a period of two (2) years from the date of original sale to the
original purchaser of equipment when recommended operating instructions and
maintenance procedures have been followed. These are packed with the machine.
Parts warranty is two (2) years, labor is six (6) months.
THIS WARRANTY IS IN LIEU OF ALL OTHER WARRANTIES EXPRESSED OR IMPLIED, AND
OF ALL OTHER OBLIGATIONS OR LIABILITIES ON OUR PART, INCLUDING THE IMPLIED
WARRANTY OF MERCHANTABILITY. THERE ARE NO WARRANTIES WHICH EXTEND BEYOND THE
DESCRIPTION ON THE FACE HEREOF.
In no event shall Gold Medal Products Co. be liable for special, incidental
or consequential damages. No claim under this warranty will be honored if the
equipment covered has been misused, neglected, damaged in transit, or has been
tampered with or changed in any way. No claim under this warranty shall be
honored in the event that components in the unit at the time of the claim were
not supplied or approved by Gold Medal Products Co. This warranty is effective
only when electrical items have been properly attached to city utility lines
only at proper voltages. This warranty is not transferable without the written
consent of Gold Medal Products Co.
The term “Original Purchaser” as used in this warranty shall be deemed to mean
that person, firm, association, or corporation who was billed by the GOLD
MEDAL PRODUCTS CO., or their authorized distributor for the equipment.
THIS WARRANTY HAS NO EFFECT AND IS VOID UNLESS THE ORIGINAL PURCHASER FIRST
CALLS GOLD MEDAL PRODUCTS CO. AT
1-800-543-0862 TO DISCUSS WITH OUR
SERVICE REPRESENTATIVE THE EQUIPMENT PROBLEM, AND, IF NECESSARY, FOR
INSTRUCTIONS CONCERNING THE REPAIR OR REPLACEMENT OF PARTS.
NOTE: This equipment is manufactured and sold for commercial use only.
10700 Medallion Drive, Cincinnati, Ohio 45241-4807 USA
gmpopcorn.com
Phone: 800-543-0862
513-769-7676
Fax: 800-542-1496
513-769-8500
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>