GOLD MEDAL 8102 Dogeroo, Super Dogeroo, and Mini Dogeroo Owner’s Manual

GOLD MEDAL 8102 Dogeroo, Super Dogeroo, and Mini Dogeroo

SAFETY PRECAUTIONS

DANGER
Machine must be properly grounded to prevent electrical shock to personnel. Failure to do so could result in serious injury, or death.
DO NOT immerse any part of this equipment in water.
DO NOT use excessive water when cleaning.
Keep cord and plug off the ground and away from moisture.
Always unplug the equipment before cleaning or servicing.
Make sure all machine switches are in the OFF position before plugging the equipment into the receptacle.

DANGER
Improper installation, adjustment, alteration, service, or maintenance can cause property damage, injury, or death. Any alterations to this equipment will void the warranty and may cause a dangerous condition. This appliance is not intended to be operated by means of an external timer or separate remote- control system. NEVER make alterations to this equipment. Read the Installation, Operating, and Maintenance Instructions thoroughly before installing, servicing, or operating this equipment.

WARNING
To avoid burns, DO NOT touch heated surfaces.
DO NOT place or leave objects in contact with heated surfaces.

ALWAYS wear safety glasses when servicing this equipment.
No user serviceable parts inside. Refer servicing to qualified service personnel.
Read and understand operator’s manual and all other safety instructions before using this equipment. To order copies of the operator’s manual go to gmpopcorn.com or write to Gold Medal Products Co., 10700 Medallion Drive, Cincinnati, OH 45241 USA 1-(800)-543-0862
DO NOT allow direct contact of this equipment by the public when used in food service locations. Only personnel trained and experienced in the equipment operation may operate this equipment.
Carefully read all instructions before operation.
This machine is NOT to be operated by minors.

Note: Improvements are always being made to Gold Medal’s equipment. This information may not be the latest available for your purposes. It is critical that you call Gold Medal’s Technical Service Department at 1-800-543-0862 for any questions about your machine operations, replacement parts, or any service questions. (Gold Medal Products Co. does not assume any liability for injury due to careless handling and/or reckless operation of this equipment.) General images may be used in manual for reference only.

INSTALLATION INSTRUCTIONS

Inspection of Shipment
After unpacking, check thoroughly for any damage which may have occurred in transit. Claims should be filed immediately with the transportation company. The warranty does not cover damage that occurs in transit, or damage caused by abuse, or consequential damage due to the operation of this machine, since it is beyond our control.

Manual
Read and understand the operator’s manual and all other safety instructions before using this equipment. To order copies of the operator’s manual go to gmpopcorn.com or write to Gold Medal Products Co., 10700 Medallion Drive, Cincinnati, OH 45241 USA 1-(800)-543-0862.

Model Description

• 8102: Dogeroo
• 8103: Super Dogeroo
• 8108: Mini Dogeroo

Setup

1. Your machine is fully assembled and tested at the factory. Carefully remove the machine from the shipping cartons. Remove all packing material and tape.
2. If the optional sneeze guard has been purchased, place it over the corner posts.
3. Be sure to place your Dogeroo where the revolving hot dogs will attract the most attention.

Accessories Included With Your Machine

Electrical Requirements
The following power supply must be provided (reference unit Data Plate):
120 V~, 60 Hz

DANGER
Machine must be properly grounded to prevent electrical shock to personnel. Failure to do so could result in serious injury, or death.
DO NOT immerse any part of this equipment in water.
DO NOT use excessive water when cleaning.
Keep cord and plug off the ground and away from moisture.
Always unplug the equipment before cleaning or servicing.
Make sure all machine switches are in the OFF position before plugging the equipment into the receptacle.

A certified electrician must furnish sufficient power for proper machine operation and install any supplied receptacle. We recommend this equipment be on a dedicated and protected circuit. Failure to wire properly will void the warranty and may result in damage to the machine. It is Gold Medal Products Co.s recommendation that this machine be plugged directly into a wall outlet. The use of extension cords is not recommended due to safety concerns, and may cause sacrificed and/or reduced performance. Make sure cord is located to prevent a trip hazard or unit upset.

Before You Plug In Machine

1. Make sure all machine switches are OFF before plugging equipment into receptacle.
2. Make sure wall outlet can accept the grounded plugs (where applicable) on the power supply cord.
3. The wall outlet must have the proper polarity. If in doubt, have a competent electrician inspect the outlet and correct if necessary.
4. DO NOT use a grounded to un-grounded receptacle adapter (where applicable).
5. Install unit in a level position.

CAUTION
If the supply cord is damaged, it must be replaced by Gold Medal Products Co., its service agent or similarly qualified persons in order to avoid a hazard.

OPERATING INSTRUCTIONS

Controls and Their Functions

ON/OFF SWITCH
Flipping the lever of this switch to the “ON” position will energize the drive motor which rotates the rotisserie. It also lights the 40 Watt bulb behind the front glass and completes the circuit to the heat control.

HEAT CONTROL
The infinite heat control allows you to vary the operating temperature of the heating element. When this control is in any position other that “OFF”, the red pilot light will be on. When the control is set at the “HI” position, the heating element is energized continually.

Specifications for Each Machine

| Dogeroo Model 8102| Super Dogeroo Model 8103| Mini Dogeroo Model 8108
---|---|---|---
Hot Dogs| 56| 84| 14
Buns| 28| 42| 14

Operating Procedure

1. Pour 1 ½ quarts of water into the water pan (about 5/8″ deep). This will keep the buns moist and warm. Use hot water to speed the process. Do NOT overfill! Overfilling will result in too much steam.
2. Place buns in the bun warmer basket.
3. Note: Some buns collect more moisture than others due to their texture.
4. Place the hot dogs on the rotisserie.
5. When ready to start cooking, move the rocker switch to the “ON” position. This will rotate the rotisserie clockwise and light the bulb behind the silk screened sign.
6. The time required to broil the hot dogs will vary, depending upon size and temperature (35-37° F refrigerated) of the hot dogs when placed in the Dogeroo.

With the heat control set on “HI” and using average size hot dogs, it will take from 10-15 minutes to have the hot dogs ready for 145° F cook temperature. Watch the dogs carefully the first several times you cook to avoid blistering or burning the hot dogs.

After the hot dogs are cooked, reduce the heat control setting to one which will keep the hot dogs at the 140° F minimum serving temperature. Hot dogs can be kept on the rotisserie for several hours without shriveling or loss of flavor, if the heat control is properly set.

Care and Cleaning

DANGER
Machine must be properly grounded to prevent electrical shock to personnel. DO NOT immerse in water. DO NOT clean appliance with a water jet. Always unplug the equipment before cleaning or servicing.

WARNING
To avoid burns, DO NOT touch heated surfaces.
DO NOT place or leave objects in contact with heated surfaces.

Good sanitation practice demands that all food preparation equipment be cleaned regularly (only use non-toxic, food grade cleaners). A clean looking, well-kept machine is one of the best ways of advertising your product.

The Dogeroo, Super Dogeroo, and Mini Dogeroo have been designed to disassemble quickly, without the use of special tools, for easy cleaning.

1. Disconnect power supply cord. Be sure unit has cooled sufficiently to permit safe handling.
2. Remove the condensate pan and basket from the bun warmer.
3. Remove the door from the bun warmer by sliding the pivot pin to the left or the right to disengage.
4. Lift the bun warmer from the top of the top frame assembly. Lift out the water pan from the top frame assembly.
5. Lift the power assembly from frame. This assembly must be cleaned by wiping with a damp cloth.
6. Lift the left end of the rotisserie from the end support. Slide rotisserie to left and disengage from motor coupling.
7. Lift out the drip pan. Slide the front and side glass upward in the slots designed in the corner posts for glass removal.
8. All parts (except power assembly) may be immersed or flooded with water for cleaning. Use a cleanser/sanitizer recommended or approved by your local Board of Health. Wipe all parts dry.
9. Reassemble in reverse order.

Care and Cleaning – Pan and Rotisserie Removal/Reassembly

TROUBLESHOOTING

Hot Dogs are Dropping from the Cradle
The rotisserie cradle is bent. Be careful removing and reinstalling the cradles. Bent cradles will not pivot freely in the rotisserie and can allow hot dogs to drop out as the unit rotates.

REPLACING BROKEN GLASS

If you accidentally break a panel of glass, it can be replaced very easily.

Note: Gold Medal Products Co. does NOT ship glass. Obtain replacement glass from your local hardware store and always purchase double strength type glass.

1. Turn unit OFF, unplug it and allow it to cool before attempting to replace the glass.
2. Remove all loose pieces of glass.
3. Remove all rigid glass channels from around the glass to be replaced. Set it aside as it must be reused.
4. Carefully remove the rest of the broken glass.
5. Apply decals (if desired) to the new glass panel.
6. Slide rigid glass channels over the exposed sides and bottom. Front and side glass slide under top and is then lowered into bottom channel.

Glass Dimensions

Side Glass: 1/8″ x 11 29/32″ x 16 3/16 (All Models)
Front Glass: 1/8″ x 13 29/32″ x 16 3/16 (Model 8102 Dogeroo)
1/8″ x 19 29/32″ x 16 3/16 (Model 8103 Super Dogeroo)
1/8″ x 8 29/32″ x 16 3/16 (Model 8108 Mini Dogeroo)

MAINTENANCE INSTRUCTIONS

DANGER
Machine must be properly grounded to prevent electrical shock to personnel. Failure to do so could result in serious injury, or death.
DO NOT immerse any part of this equipment in water.
DO NOT use excessive water when cleaning.
Keep cord and plug off the ground and away from moisture.
Always unplug the equipment before cleaning or servicing.
Make sure all machine switches are in the OFF position before plugging the equipment into the receptacle.

DANGER
Improper installation, adjustment, alteration, service, or maintenance can cause property damage, injury, or death. Any alterations to this equipment will void the warranty and may cause a dangerous condition. This appliance is not intended to be operated by means of an external timer or separate remote- control system. NEVER make alterations to this equipment. Read the Installation, Operating, and Maintenance Instructions thoroughly before installing, servicing, or operating this equipment.

WARNING
No user serviceable parts inside. Refer servicing to qualified service personnel.

CAUTION
THE FOLLOWING SECTIONS OF THIS MANUAL ARE INTENDED ONLY FOR QUALIFIED SERVICE PERSONNEL WHO ARE FAMILIAR WITH ELECTRICAL EQUIPMENT. THESE ARE NOT INTENDED FOR THE OPERATOR.

ORDERING SPARE PARTS

1. Identify the needed part by checking it against the photos, illustrations, and/or parts list. (General images may be used in manual for reference only.)
2. Use only approved replacement parts when servicing this unit.
3. When ordering, please include part number, part name, and quantity needed.
4. Please include your model number, serial number, and date of manufacture (located on the machine nameplate/data plate) with your order.
5. Address all parts orders to Parts Department, Gold Medal Products Co., 10700 Medallion Drive, Cincinnati, Ohio 45241-4807
   or place orders by phone or online:

Phone: 800-543-0862
513-769-7676
Fax: 800-542-1496
513-769-8500
E-mail: info@gmpopcorn.com
Web Page: gmpopcorn.com

Cabinet Exterior – Front View

Cabinet Exterior – Back View

Power/Control Unit and Rotisserie

Power/Control Unit and Rotisserie – Parts List

87882
8| ROTISSERIE| 1| 87737| 87153| 87830
9| ROTISSERIE CRADLE| 14| 87740| 87151| 87831
10| END SUPPORT, ROTISSERIE| 1| 87020| 87020| 87020
11| ¼-20 SERRATED NUT| 2| 46311| 46311| 46311
12| OFFSET STRIP| 1| 87079| 87079| 87079
13| HEAT ELEMENT| 1| 88160| 87122| 87915
14| BRACKET, ELEMENT TIE DOWN| 1| 87080| 87080| 87080
15| STRAIN RELIEF| 1| 67060| 67060| 67060
16| POWER CORD, 15 AMP| 1| 87085| 87085| 87085
17| MOTOR ASSEMBLY| 1| 87713| 87713| 87713
18| SOCKET SUPPORT TUBE| 1| 87708| 87728| 87828
19| LAMP SOCKET| 1| 11034| 11034| 11034
20| COATED 40W CLEAR BULB| 1| 87065C| 87065C| 87065C

Power/Control Unit – Interior

Accessories

WIRING DIAGRAM

Model No. 8102, 8103, 8108

WARRANTY

Gold Medal Products Co. warrants to the original purchaser each item of its manufacture to be free of defects in workmanship and material under normal use and service. Gold Medal Products Co.’s obligation under this warranty is limited solely to repairing or replacing parts, f.o.b. Cincinnati, Ohio, which in its judgment are defective in workmanship or material and which are returned, freight prepaid, to its Cincinnati, Ohio factory or other designated point. Except for “Perishable Parts” on specific machines, the above warranty applies for a period of two (2) years from the date of original sale to the original purchaser of equipment when recommended operating instructions and maintenance procedures have been followed. These are packed with the machine. Parts warranty is two (2) years, labor is six (6) months.
THIS WARRANTY IS IN LIEU OF ALL OTHER WARRANTIES EXPRESSED OR IMPLIED, AND OF ALL OTHER OBLIGATIONS OR LIABILITIES ON OUR PART, INCLUDING THE IMPLIED WARRANTY OF MERCHANTABILITY. THERE ARE
NO WARRANTIES WHICH EXTEND BEYOND THE DESCRIPTION ON THE FACE HEREOF. In no event shall Gold Medal Products Co. be liable for special, incidental or consequential damages. No claim under this warranty will be honored if the equipment covered has been misused, neglected, damaged in transit, or has been tampered with or changed in any way. No claim under this warranty shall be honored in the event that components in the unit at the time of the claim were not supplied or approved by Gold Medal Products Co. This warranty is effective only when electrical items have been properly attached to city utility lines only at proper voltages. This warranty is not transferable without the written consent of Gold Medal Products Co.
The term “Original Purchaser” as used in this warranty shall be deemed to mean that person, firm, association, or corporation who was billed by the GOLD MEDAL PRODUCTS CO., or their authorized distributor for the equipment.

THIS WARRANTY HAS NO EFFECT AND IS VOID UNLESS THE ORIGINAL PURCHASER FIRST CALLS GOLD MEDAL PRODUCTS CO. AT 1-800-543-0862 TO DISCUSS WITH OUR SERVICE REPRESENTATIVE THE EQUIPMENT PROBLEM, AND, IF NECESSARY, FOR INSTRUCTIONS CONCERNING THE REPAIR OR REPLACEMENT OF PARTS.
NOTE: This equipment is manufactured and sold for commercial use only.

10700 Medallion Drive, Cincinnati, Ohio 45241-4807 USA gmpopcorn.com

Phone: 800-543-0862
513-769-7676

Fax: 800-542-1496
513-769-8500

© 2018 – The text, descriptions, graphics, layout, and other material in this publication are the exclusive property of Gold Medal Products Co. and shall not be used, copied, reproduced, or published in any fashion, including website display, without its express written consent.
gmpopcorn.com

References

• Concession Supplies & Equipment | Gold Medal Products Co.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>