GOLD MEDAL ReadyPop Jr. Base Robust Stainless-Steel Rolling Cabinet Instruction Manual

ReadyPop® Jr. Unit and Base

Export Model No.: 2783 Series and 2793 Series Base

Optional — Mount Unit on a ReadyPop Jr. Base

1. Position base on a level surface and lock the caster wheels into place.
2. Remove wastebasket from base (reference description below).

1. Insert
2. Wastebasket

To Remove Wastebasket:
1. Lift insert off the base.
2. Lift wastebasket out of base.

3. Set ReadyPop Jr. on base—position popper so debris bin is under the dispenser and place feet into holes provided, see image below.
4. Fasten unit to base—insert a screw w/washer up through the hole in the base, and into the popper until snug. Repeat for each corner, then tighten all 4 screws to secure.
5. Route the popper’s power cord into the base, see image below. Reference the Electrical Requirements section to plug in the power cord from the base.
6. Attach Shelf Option (PN 121014), if applicable (option sold separately).
7. Reinstall wastebasket and insert before use.

Install Ready Pop Jr. on Base

1. Detail A Mounting Screw:
   (4) 8-32 x 1/2 Screw w/Washer

2. Route Power Cord into base.

3. Plug Popper into base.

4. Receptacle in Base
   a: (4) Shelf fastene (if needed)
   b: Remove Insert and Wastebasket to access mounting locations.

For an extra dirty kettle, the process may be repeated; or, after turning kettle heat OFF, allow solution to sit in kettle overnight. The next morning, finish the cleaning steps.

9. With unit OFF and unplugged, use a clean SLIGHTLY damp cloth (wring ANY EXCESS water from cloth before use) and wipe the kettle lead cord clean. DO NOT get moisture into the kettle lead-in cord, severe damage will result.
10. After kettle cleaning, check to be sure the crossbar fasteners on the kettle are securely tightened.

Daily Unit Cleaning Instructions (Base, if equipped)

1. Turn machine OFF, unplug unit and allow it to cool before attempting to clean.
2. Remove the old maid pan, coil assembly, and corn pans—take them to the sink to clean with soap and water, then rinse and dry.

To remove coil and corn pans: (refer to Coil and Corn Pan Removal in Installation section)

1. Remove any remaining popcorn.
2. Remove the 2 side corn pans.
3. Unscrew coil assembly to remove it from motor shaft.
4. Lift the bottom corn pan out of unit.

3. As needed, use a vacuum under corn pan to remove any debris.
4. Units with a Base: Remove debris from wastebasket and wipe out to clean (discard any popcorn from wastebasket). Reference description below to remove wastebasket—after cleaning reinstall for use.

1. Insert
2. Wastebasket

To Remove Wastebasket:
3. Lift insert off the base.
4. Lift wastebasket out of base.

5. Clean area above the corn pans and exterior using a clean, SLIGHTLY damp cloth to remove any grease from glass and cabinet (cloth may be SLIGHTLY dampened with soap and water, then wipe again with clean water to remove any remaining cleaner).
6. Clean glass panels with glass cleaner. Gold Medal Watchdog Glass Cleaner (Item No. 2588) is recommended.
Ammonia cleaners will damage plastic doors/panels. Only use a non-ammonia cleaner, such as Gold Medal Watchdog Glass Cleaner (Item No. 2588).
7. Reinstall the clean and dry pans/accessories.
8. Check the kettle lead cord, make sure it is fully plugged into the kettle receptacle and the plug is fully twisted to lock it into place.

Model 2793-01-000 Base

*CAUTION: If supply cord is damaged, it must be replaced by Gold Medal Products Co., its service agent, or similarly qualified persons in order to avoid a hazard.

A: Fasteners for shelf option (if applicable).
B: Fasteners to attach Popper.
C: Hinge and Fasteners

A: Receptacle View

A: See receptacle parts view above.
B: Receptacle in Base Interior

2793-01-000
1| INSERT| 120224
2| WASTE BASKET| 37019
3| 8-32 X 1/2 PH PAN W/SEMS| 47124
4| 1.5IN SPLIT SNAP GROMMET| 114434
5| 1/4-20 X 1/2 P/H PHIL| 12471
6| 1/4-20 SERRATED LOCK NUT| 46311
7| 3 IN RIGID CASTER| 69962
8| 3 IN HD CASTER W/BRAKE| 115543
9| 5/16-18 SERRATED LOCK NUT| 49317
10| WASHER 5/16 INT TOOTH| 74137
11| 5/16-18 X 5/8 PH TR M/S| 46638
12| DOOR| 114953
13| MALE HINGE SHORT RIGHT| 41350
14| FEMALE HINGE LEFT| 41355
15| 8-32 X 3/8 PAN HD PH M/S| 12389
16| 8-32 SERRATED FLANGE NUT| 61151
17| DRAWER HANDLE| 87420
18| 10-24 X 1/2 PH TRUSS M/S| 42826
19| DOOR CATCH| 12045
20| 6-32 X 3/8 PHIL PAN M/S| 39000
21| 6-32 GRIP NUT ZINC PLATED| 47517
22| BUSHING, SNAP 3.500 IN| 67802
23| RECEPTACLE BOX ASSEMBLY (incls receptacle box and bracket)| 114622
24| SCREW #8-32X3/8 PAN HD PH| 74141
25| 8-32 X 3/8 PH PAN W/SEMS| 42227
26| 8-32 HEX M/S NUT| 74149
27| SCHUKO OUTLET TYPE F| 114645
28| RECEPTACLE PLATE| 114481-01
29| 6-32 X 3/8 PH FL HD M/S| 47772
30| 6-32 GRIP NUT ZINC PLATED| 47517
31| STRAIN RELIEF SR-6P3-4| 76026
32*| POWER SUPPLY CORD, EXPORT| 42369

gmpopcorn.com

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>