SABRENT EC-T3DN Rugged ThunderBolt 3 To NVMe M.2 SSD Tool-Free Dual Enclosure Installation Guide

RUGGED THUNDERBOLT™ 3 TO NVMe M.2
SSD TOOL-FREE DUAL ENCLOSURE

EC-T3DN QUICK INSTALLATION GUIDE

FEATURES

• Turn two NVMe SSDs into two independent, fast, reliable, and portable drives.
• Intel’s Thunderbolt™ 3 controller inside.
• Single disk speed up to 1500 MB/s *. Software RAID speed up to 2500 MB/s **.
• Solid aluminum construction for durability and maximum heat dissipation.
• Integrated temperature and health monitoring system.
• Tool-free fasteners.
• M.2 size compatibility: 80mm (2280), 60mm (2260), and 42mm (2242).
• Plug and play. No drivers needed.
• Power adapter is required and included.
• Performance will depend both on the speed of your NVMe disk and your system’s overall performance.
• RAID array is only possible via software.

NOTE: Only for NVMe M-Key SSDs (PCle-based). Does NOT support SATA-based or AHCl-based SSDs. NVMe disks NOT included.

PACKAGE CONTENTS

1. Rugged Thunderbolt™ 3 to NVMe M.2 SSD Tool-free Dual Enclosure
2. Thunderbolt™ 3 cable
3. Power adapter: 110V-240V AC
4. Quick user guide

SYSTEM REQUIREMENTS

• Windows / Mac / Linux

DISK INSTALLATION

STEP 1
Lift the knob.

STEP 2
Rotate (counter clockwise) to unlock the knob.

STEP 3
Open the button plate.

STEP 4
At a 45-degree angle, insert the Magnetic Pins in the SDDs notch and slide in your SDDs until they are properly seated.

STEP 5
Make sure de Magentic Pin “clicks” in the bottom

STEP 6
Reattach the bottom plate, rotate to lock the knob (clockwise) and put the knob down. (Finish the installation)

CONNECTING FOR THE FIRST TIME VIA THUNDERBOLT™ 3

Connect your Sabrent external drive to your computer as shown in the diagram. Make sure to confirm your computer’s port has the  Thunderbolt™ 3 logo, otherwise it will likely be a standard USB 3 Type-C port. When using any Thunderbolt™ 3 device for the first time, your operating system might need you to approve the connection. If this is the case, select “Always Connect” and click “OK”. You can alternatively select “Ask Every Time” if you need to do so for security reasons.

TROUBLESHOOTING YOUR THUNDERBOLT™ 3 DEVICE

To troubleshoot the scenario where a Thunderbolt™ 3 device is not recognized properly, we suggest checking following items:

1. Make sure that both the computer and the device are turned on and that the Thunderbolt™ 3 device is connected to the computer via the Thunderbolt™ interface.
2. Disconnect and re-connect the Thunderbolt™ cable and/or restart the computer.
3. Use the Thunderbolt™ 3 cable that was included. If you own a second cable, test both to rule out any problems with the cable.
4. Confirm that your computer supports Thunderbolt™. If it has a USB-C port but only supports USB, the Thunderbolt™ device  won’t work.5. For Windows PCs, update the BIOS of your computer.
5. For Windows PCs, update the Thunderbolt™ firmware (NVM) on your computer.
6. For Windows PCs, update the Thunderbolt™ software (driver) on your computer.
7. For Windows PCs, when you connect a new device for the first time, you might have to approve the device. Select “Always  Connect”.
8. For Windows PCs, if the device is recognized at first but disconnecting and re-connecting fails, install the device driver for  Windows.
9. For Windows PCs, if the device is no longer recognized after upgrading your operating system (e.g. from Windows 7 to Windows  10), uninstall the Thunderbolt™ software and re-install the latest version, even if it’s the same version.

DRIVE IS CONNECTED BUT MISSING IN FILE EXPLORER

1. Open Disk Management with administrator permissions. To do so, in the search box on the taskbar, type Disk Management, select and hold (or right-click) Disk Management, then select Run as administrator > Yes. If you can’t open it as an administrator, type Computer Management instead, and then go to Storage > Disk Management.
2. In Disk Management, right-click on the disk that appears Offline, then click Online (shown here).

USING A HARD DISK WITH DATA ON IT

1. Make sure everything is connected.
2. If you are using an HDD that already has a file system and data on it, it should appear under your Computer after a few seconds of being powered on. In some cases, it may take up to 30 seconds.

NOTE: There are some exceptions. For instance, if you are trying to use an HDD that was pulled from a Linux or an Apple computer on a Windows computer, it might not work. This has nothing to do with your Sabrent enclosure, it happens because the Windows operating systems is not capable of seeing the file system that is used in Linux or Apple computers.

USING A BRAND NEW HARD DISK

If you are using a brand new HDD, you might have to initialize it before you can use it.

NOTE: Only initialize a disk if you are absolutely sure it is a brand new disk and it does not have any of your data on it. The initializing process destroys all previous data and renders it irretrievable.

TO INITIALIZE NEW DISKS

3. Open Disk Management with administrator permissions. To do so, in the search box on the taskbar, type Disk Management, select and hold (or right-click) Disk Management, then select Run as administrator >  Yes. If you can’t open it as an administrator, type  Computer Management instead, and then go to Storage > Disk Management.

4. In Disk Management, right-click the disk you want to initialize and then click Initialize Disk (shown here). If the disk is listed as Offline, first right-click it and select Online.
5. In the Initialize Disk dialog box (shown here), check to make sure that the correct disk is selected and then click OK to accept the default partition style. If you need to change the partition style (GPT or MBR), you can do it here. The disk status briefly changes to  Initializing and then to the Online status.
6. Select and hold (or right-click) the unallocated space on the drive and then select New Simple Volume.
7. Select Next, specify the size of the volume (you’ll likely want to stick with the default, which uses the whole drive), and then select Next.
8. Specify the drive letter you want to assign to the volume and then select Next.
9. Specify the file system you want to use (usually NTFS), select Next, and then Finish.

Please contact our Technical Support Team for additional troubleshooting
Thunderbolt and the Thunderbolt logo are trademarks of Intel Corporation or its subsidiaries in the U.S. and/or other countries. All other brands and logos belong to their corresponding owners.

WWW.SABRENT.COM
EG-T3DN QUICK INSTALLATION GUIDE

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>