ECOSENSE F170 Rise Macro Aiming System Installation Guide
- June 6, 2024
- ECOSENSE
Table of Contents
ECOSENSE F170 Rise Macro Aiming System Installation Guide
INSTALLATION GUIDE
MACRO™ Aiming System
INCLUDED
RISE F170 QUAD Installation Guide
RISE F170 QUAD Guide d’installation / Guía de instalación QUAD para RISE F170
Every lighting fixture includes firmware that facilitates electronic
dimming control
- For other RISE Installation Guides visit https://[www.ecosenselighting.com/resources/#rise](http://www.ecosenselighting.com/resources/#rise)
OPTIONAL ITEMS
Interchangeable Lens
Lentilles Interchangeables
Color Filter
Filtre de Couleur
Snoot
Coupe-Flux
EcoSpec® LDCM 0-10V Module
EcoSpec® LDCM 0-10V Module / EcoSpec® LDCM 0-10V Módulo
EcoSense Tenon, RISE-MULTI-SMP-(Finish)
Tenon EcoSense, RISE-MULTI-SMP-(Finition) / EcoSense Tenon, RISE-MULTI-SMP-
(Acabado)
- For more accessories visit https://www.ecosenselighting.com/products/#rise-accessories
NOTES
Screw Torque Settings:
- Screws to replace the Lens and Bezel: Screws for MACRO™ Lock Pan and Tilt: Screw for main tilt arm:
- Set screws for tenon mount:
- EC Cable Length:
- Wire Color Description:
- Hex 3 mm; 1.25 Nm ± 0.25 Nm Hex 5 mm; 27.0 Nm ± 2.0 Nm Hex 6 mm; 27.0 Nm ± 2.0 Nm Hex 4 mm; 9.5 Nm ± 0.5 Nm 3.048 m (10 ft)
- Brown or Black = Line
- Blue or White = Neutral
- Green or Green/Yellow = Ground
INSTALLATION GUIDE
INSTALL THE FIXTURE
- Connect the wires from the fixture to the building wires.
- Slide the base of the tenon mount over the tenon until the fixture can no longer slide down.
- Swivel the fixture about the tenon to pan it to the desired direction.
- Tighten the 4 set screws using a 4mm hex driver or key to 9.5 Nm.
- Use a 6mm hex driver or key to loosen the main tilt arm screw to tilt all four heads to the desired direction. Re-tighten to 27 Nm.
- Use a 5mm hex driver or key to loosen the MACRO™ Lock screws if individual head aiming is needed. Re-tighten to 27 Nm.
NON-ECOSENSE TENON
OPTIONAL INSTALL-F170 INTERCHANGEABLE LENS
- Loosen the four screws on the Back Bezel with a 3mm hex driver or key until the Front Bezel comes off. Screws are captive and will not fully disengage.
- Remove the center screw using a 3 mm hex driver or key from the lens.
- Remove the old lens and install the new lens. Refer to Lens Installation Instructions for specifics.
- Replace the new Lens and then re-fasten the Center Screw to 1.5 Nm.
- Secure the Front Bezel and tighten with the four screws from the back to 1.5 Nm.
OPTIONAL INSTALL-F170 SNOOTS
- Loosen the four screws on the Back Bezel with a 3 mm hex driver or key until the Front Bezel comes off.
- Place the Snoot on and then tighten the four screws from the back to 1.5 Nm.
FULL SNOOT
Documents / Resources
|
ECOSENSE F170 Rise Macro Aiming
System
[pdf] Installation Guide
F170, Rise Macro Aiming System
---|---
References
- Ecosense Lighting: LED Technology | Linear and Flood LED Lighting
- Ecosense Lighting: LED Technology | Linear and Flood LED Lighting
- Products - Ecosense Lighting
- Products - Ecosense Lighting
- Downloads - Ecosense Lighting
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>