Holiday LIVING 4124146 4 Foot Animated Reindeer User Manual

ITEM # 5280914

4-FT ANIMATED REINDEER

MODEL # 4124146

HOLIDAY LIVING and logo design are trademarks or registered trademarks of LF, LLC. All rights reserved.

Serial Number __ Purchase Date __

Questions, problems, missing parts? Before returning to your retailer, call our customer service department at 888-251-1006, 8 a.m. – 8 p.m., EST, Monday – Sunday. You could also contact us at partsplus@lowes.com.

SS23357

BEFORE ASSEMBLY

• Remove all parts and hardware from the box. Place all items on a carpeted or scratch-free work surface, as this will avoid damaging parts during assembly.
• The shipping box can provide an ideal work surface if none is available.
• Use the components and hardware lists below to identify, inventory and separate each of the hardware and components included.
• To avoid accidentally discarding small components or hardware, do not dispose of any packaging or contents of the shipping carton until assembly is complete.
• DO NOT USE power tools unless it is explicitly identified in this manual as required for use during assembly. Power tools can damage the fasteners, hardware and/or components.
• Do not fully tighten all fasteners / screws until all parts are in place. Failure to follow these instructions may cause the fasteners / screws to misalign during assembly.

CARE INSTRUCTIONS

• Use a soft, clean cloth that will not scratch the surface when cleaning.
• Do not wash, do not bleach, do not dry, do not iron, do not dry clean.
• Colours, style and contents may vary slightly from those shown on the package.

SAFETY INFORMATION

Please read and understand this entire manual before attempting to assemble, operate or install the product.

DANGER
The item should not be grabbed or to be climbed on, as it becomes a tipping hazard. Keep away from the adapter, as it heats up during operation.

PREPARATION

Before you begin with assembly of the product, make sure all parts are present. Compare parts with package contents list. If any part is missing or damaged, do not attempt to assemble the product.

Estimated Assembly Time: 15 minutes
Tools Required for Assembly (included): Allen Wrench

PACKAGE CONTENTS

PART

| DESCRIPTION|

QUANTITY

---|---|---

A

| Body|

1

B

| Left Front Leg|

1

C

| Right Front Leg|

1

D

| Left Hind Leg|

1

E

| Right Hind Leg|

1

F

| Head|

1

G

| Left Antler|

1

H

| Right Antler|

1

I

| Screws, Allen Wrench and Stakes|

1

J

| Adapter|

1

HARDWARE CONTENTS (shown actual size)

(aa) M6 X 54mm Screws Qty. 4

(bb) M6 X 40mm Screws Qty. 2

(cc) M4 X 58mm Qty. 1

ASSEMBLY INSTRUCTIONS

1. Position the (A) Body Frame with Function Box on a flat soft ground and flip it over as shown in Figure 1.

OPTIONAL: If you choose to use the Step Activation Pad, plug the connector into the input receiving jack marked “TRY ME on the Function Control Box and set the Step pad in front of the character when ready to display.

Note: Do not plug the Power Adapter into power outlet until item assembly is completed.

Warning: Waterproof cap must cover Try Me receiver when not in use.

2. Fit the (B, C, D, E) Legs onto the (A) Body before fastening the screws Ensure that the screws are securely fastened. But not too tight to avoid damage on the thread.

3. Fit the (F) Head by initially removing the cotter pin on the forked hook beneath the head as shown in Figure 3.1. Insert forked hook into the forked hook housing available on top of the (A) Body as shown in Figure 3.2. Then re- insert the cotter pin back to the forked hook as shown in Figure 3.3.

4. Remove the cotter pin from the prong available at the bottom of the (F) Body as shown in Figure 4 1. Connect the prong to the gear arm from the gear box available from the (A) Body as shown in Figure 4.2. Then re-insert the cotter pin into the prong as shown in Figure 4 3.

5. Connect the available cable from the (F) Head to the cable from the gear box as shown in Figure 5.1. And connect the other end of the mane to the (A) Body using the available hook and loop closure as shown in Figure 5.2.

6. Close the mane from the (F) Head using the available zipper as shown in Figure 6.1. Fit both the (H, G) Antlers on top of the (F) Head and fasten the screws. Ensure that the screws are securely fastened. But not too tight to avoid damage on the thread.

7. To secure the prop to the ground, place all (dd) Stakes on the slot available on each of the hooves of the (B, C, D, E) Legs as shown in Figure 7.1. To avoid tripping from the wire, secure the (J) Adapter wire to the wire clips available as shown in Figure 7.2.

Your Animated Reindeer is fully assembled. Plug in and turn on to let the fun begin!

1. SENSOR
   Be sure nothing is blocking the sensor.

OPERATION INSTRUCTIONS

1. Plug the power adapter into a standard power outlet and adjust the settings on the Function Control Box, located on the (A) Body as desired.
2. Settings:

ON

| This switch mode will continuously operate the lights, sound, and animation of the item.
---|---

OFF/TRY ME

| This switch mode allows the item to be activated only if triggered by using a Step Here Try Me Activation Pad (Not Included). The item will operate for one audio cycle with each Try Me activation.

SENSOR

| This switch mode will activate lights, sound, and animation when the Infra- red (IR) sensor is activated and will operate for 1 audio-cycle with each activation. The Infra-red (IR) sensor has a range of up to 2 m/6.5 ft. and will activate when someone comes within an 80-degree angle from left-to-right, as well as from above and below.
| Raise or lower the volume using the volume control turn dial, turn all the way down to turn the volume off.

WARNING

This item is not a toy and should be used for decoration only. This item contains small parts that can be a choking hazard. Keep all plastic and wire parts away from children. For indoor and outdoor use.

1. Please use the adapter supplied by the manufacturer.
2. Please assemble the item according to the instructions. Connect all wires according to their matching color.
3. Usage near children should be supervised by adults.
4. Keep away from open flame.
5. Don’t climb or pull on product.
6. Don’t add to or modify product.
7. Assemble and place the product on level surfaces only.
8. Don’t push or tilt product.

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

CAUTION

Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.

NOTE

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on the user is encouraged to try to correct the interference by one or more of the following measures. Reorient or relocate the receiving antenna, Increase the separation between the equipment and receiver, Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or experienced radio/TV technician for help.
Seasonal Visions International, Berkeley, CA 94710 USA 855-428-3921.

TROUBLESHOOTING

Problem

| Possible Cause|

Prevention & Solution

---|---|---
1. Item is not functioning.| 1. Adapter is not plugged in to the wall and/or function control box.| 1. Plug the adapter into the wall and function control box when assembly is complete.
2. Item is not functioning in the way anticipated.| 2. The function control box switch may not be on the desired setting.| 2. Toggle switch to desired setting. For example, if you only want the item to trigger by sensor, ensure that the switch is toggled to SENSOR.
3. Some of the item is functioning, but not all of it. For example, LED is not lighting up, but everything else is working.| 3. The cable for the non- functioning part of the item may not be connected.| 3. Ensure all cables are connected before operating the item.
4. Sensor is not working.| 4. Something may be blocking the sensor.| 4. Adjust the sensor so that it is facing forward and that nothing is covering it. Refer to instructions for assistance.
5. Movement is slowing down, appears jerky and/or there’s unwanted noise from the moving parts.| 5. Something may be obstructing the moving parts.| 5. Remove the item that is stuck in the moving parts and adjust the item so this is less likely to happen again.
6. Item is wobbling in place.| 6. The item may be placed on a surface that is rough, not flat or not level.| 6. Be sure to place your item on a flat surface and ensure that all 4 stakes are placed firmly.
7. The item does not make any sound.| 7. The volume may be turned all the way down. | 7. Turn up the volume to see if this is the issue.

CARE & USE INSTRUCTIONS

STORAGE INSTRUCTIONS

1. Carefully place all components into shipping box and/or provided container tape it shut.
2. When not in use, please store your item in a cool, dry place away from sunlight.
3. Exposing your item to excessive heat or humidity may damage your item.

TECHNICAL DATA

Input: 120V AC 50/60Hz
Output: 5.9V DC 1.5A

WARRANTY INFORMATION

Please remove all parts from the box to check them against this list before attempting to assemble.
If any part is missing or unsatisfactory, please call our toll-free number 888-251-1006 or email us at partsplus@lowes.com.
Thank you!

Printed in China

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>