AUDIOropa Xepton T-1 Stationary Transmitter User Manual
- June 6, 2024
- AUDIOropa
Table of Contents
AUDIOropa Xepton T-1 Stationary Transmitter
General information
Thank you very much for purchasing the »exception« communication system! You have chosen a modern and reliable system. Please read this manual carefully to be able to set up the unit correctly and to familiarise yourself with all of the features of the system. Septon« is an ideal system for application within groups – ranging from simple dialogue to interpreter-, team-teaching- and conference systems. Being slim and lightweight in design, it combines quality and versatility with easy use and state-of-the-art radio technology.
Scope of delivery xepton T-1
Please check if all of the following components are included:
- Septon T-1
- Soft storage case
- USB power lead and – power supply
- User manual
- Warranty card
Should any parts be missing, please contact your dealer or the manufacturer directly.
Main Features
- Worldwide compatibility due to restriction-free 2.4 GHz transmission
- Supports an unlimited amount of receivers »Septon RX-1«
- 40 selectable channel groups
- The »xepton RP-1« can be used in two-way communication with up to two » exception TRX-1« transceiver units per channel group.
- Large signal range of up to 300 m
- Completely digital crystal-clear sound quality
- Microphone sensitivity adjustable in 5 levels
- 9 selectable levels of volume
- Can be powered with a portable USB power pack
xepton T-1 Transmitter
Controls and displays
How to use
Power ON / OFF
Connect the device with the USB power supply and cable, by using either one of the two USB sockets on the rear of the device. Use the ON/OFF switch to switch the device on. The LC displays will illuminate and the default volume setting „VOL 03“ is indicated respectively. Use the ON/OFF switch again to switch the device off.
Group selection
The two control units A and B must be set to different channel groups. Switch the device on and press and hold one of the MODE buttons for 3 seconds. The symbol »GRP« in the display above the pressed MODE button will blink. Select a group number of your choice between »00« and »39« by pressing the and -buttons. After the selection, wait for 3 seconds for the selected group number to be set. Please note: For both units, choose a group number with a large difference (e.g. A:00 / B:20), as this will enhance the performance. Press and hold the other MODE button for 3 seconds. The selection of the group number is as described above but choose a different channel number. Transmitters and receivers must be set to the same group number if they are to communicate with each other.
ID selection
For full two-way applications between units A and B, both units must be set as MASTER. Units are defined as MASTER by setting their ID to »00«. If further xepton TRX-1 transceivers are to be included within the according to group, each TRX-1 needs to have its ID set to any number but »00«, as there only can be one master unit within a channel group. To transmit voice from the microphone, the TALK button of additional TRX-1 units needs to be pressed for one second in order to enable the TALK function. When using the transmitters T-1 and/or TX-1, the unit of the repeater assigned to their channel group must not be set to MASTER. To set a unit as MASTER, continue as follows: On the powered-up device, press and hold the MODE button for 3 seconds. The symbol »GRP« on the display will blink. Press the MODE button again. The symbol »ID« will start to blink. By using the and -buttons, select the ID from 00 to 99. Setting the ID to 00« will define the unit as MASTER. After the selection, wait for 3 seconds to set the selected ID number.
Volume up / down
The volume of the according unit can be adjusted through 9 levels. On the powered-up device, press the between 01 (low) and 09 (high) as desired.
Monitoring function On / Off
The monitoring function enables you to hear your own voice over the system. Proceed as follows if you wish to activate the monitoring function: On the powered-up device, press and hold the MODE button of the according to unit for 3 seconds. The symbol »GRP« in the display will blink. Press the MODE button two times. The »SO« symbol in the display will blink. By using the and -buttons, select »SO« to activate the monitoring function or »SF« to deactivate it. After the selection, wait for 3 seconds for the selected function to be set.
Please note:
The default setting is »SF« (monitoring deactivated).
Microphone sensitivity
The microphone sensitivity for the according unit can be adjusted through 5 levels, as needed in regards to environmental requirements: On the powered-up device, press and hold the MODE button for 3 seconds. The symbol »GRP« in the display will blink. Press the MODE button three times. The »C1« symbol in the display will blink. By using the and -buttons, select between C1 (low sensitivity) and C5 (high sensitivity).
Please note: The default setting is C3.
Basic audio output high/low
Apart from the volume control, it is possible to adjust the basic audio output level. The higher audio output will raise the maximum volume – this might be required in noisy surroundings. On the powered-up device, press and hold the MODE button of the according to unit for 3 seconds. The symbol »GRP« in the display will blink. Press the MODE button four times. The »UH« symbol is shown in the display. By using the and -buttons, select UH (high output) or UL (normal output). After the selection, wait for 3 seconds to set the selected output level.
Please note:
Selecting »UH« can cause white noise and should only be used in loud
environments. We recommend the default setting »UL«.
Power supply
The repeater is powered over either one of the USB connectors on the rear of the device. The device can be powered by a regular USB power pack for mobile phones and can hereby be used in a portable manner. Connect the power pack to the USB connector on the rear of the device. The power consumption of the device is approx. 400mA.
Application
Transmitting with T-1 and receiving with RX-1
An unlimited amount of RX-1 or RX-1U receivers can be used to receive the transmission of the T-1. All devices must be set to the same channel group number.
Two-way communication with transmitter T-1 and two TRX-1 transceivers
It is possible to have two-way communication between the T-1 transmitter and two TRX-1 transceivers. All devices must be set to the same channel group number and each device must have its own ID number, with one device having the master-ID »00«.
Two-way communication with transmitter T-1, two TRX-1 transceivers and RX-1
receivers
It is possible to have two-way communication between the T-1 transmitter and two TRX-1 transceivers. An unlimited amount of RX-1 or RX-1U receivers can receive the transmission. All devices must be set to the same channel group number and each transmitter device must have its own ID number, with one transmitter device having the master-ID »00«.
Pin-layout XLR
- 4 Pin XLR on the front panel
- 3 Pin XLR on the rear panel
Specifications xepton T-1
- Device type Repeater
- Dimensions 37 x 230 x 124 mm (H x W x D)
- Weight 390 g
- Frequency type ISM 2403 – 2480 MHz
- Transmission mode ISM 2.4 GHz FSK modulation with frequency
- Transmission power hopping
- Voice codec Maximum 10 mW
- RX-sensitivity 16bit / 8 KHz
- Latency -95 dBm
- Data rate < 35 ms
- Frequency bandwidth Power 2 Mbps
- Power consumption 2 MHz
- Range up to 300 m
- Frequency response 50 Hz – 7 kHz
Conformity
This device complies with the following EC directives:
- 2011 / 65 / EC RoHS-directive
- 2012 / 19 / EC WEEE-directive
- 2014 / 53 / EC RED-directive
Compliance with the directives listed above is confirmed by the CE seal on the device. The complete CE compliance declaration is available on the internet at www.humantechnik.com. Specifications subject to change without prior notice.
Maintenance and care
All »exception«-devices do not require any maintenance. If they become dirty,
simply wipe them clean with a soft, damp cloth. Never use spirits, thinners or
other organic solvents. Do not expose them to full sunlight. In addition, they
must be protected against excessive heat, moisture and severe mechanical
shocks.
Note: These products are not protected against splash water. Do not place
any containers filled with water, such as flower vases, or anything with an
open flame, such as a lit candle, above or near the products.
Warranty
All »exception«-devices are very reliable products. Should a malfunction occur
despite the unit having been set up and operated correctly, please contact
your dealer or the manufacturer directly.
This warranty covers the repair of the product and returning it to you free of
charge. It is recommended that you send in the product in its original
packaging, so keep the packaging for the duration of the warranty period. The
warranty does not apply to damage caused by incorrect handling or attempts to
repair the unit by unauthorized persons (destruction of the seal on the unit).
Repairs will only be carried out under warranty if the completed warranty card
is returned accompanied by a copy of the dealer’s invoice/till receipt. Always
specify the product serial number in any event.
Disposal of used electrical and electronic units (applicable in the countries of the European Union and other European with a separate collection system). The symbol on the product or the packaging indicates that this product is not to be handled as ordinary household waste but has to be returned to a collecting point for the recycling of electrical and electronic units. You protect the environment and health of your fellow man by the correct disposal of this product. Environment and health are endangered by incorrect disposal. Material recycling helps to reduce the consumption of raw materials. You will receive further information on the recycling of products from your local community, our communal disposal company or your local dealer.
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>