AUDIOropa Xepton-NX TR Stationary Transmitter User Manual

AUDIOropa Xepton-NX TR Stationary Transmitter

introduction

Thank you very much for purchasing »Septon-NX«! You have chosen a modern and reliable communication system. Please read this manual carefully to be able to set up the unit correctly and to familiarise yourself with all of the features of the system. Septon-NX« is an ideal system for application within groups – ranging from simple dialogue to interpreter-, team-teaching- and conference systems.
Being slim and lightweight in design, it combines quality and versatility with easy use and state-of-the-art radio technology.

Scope of delivery xepton-NX TR

Please check if all of the following components are included:

• xepton-NX TR
• USB cable
• USB power supply
• Mounting brackets and screws
• User manual
• Warranty card
• Should any parts be missing, please contact your dealer or the manufacturer directly.

Main Features

• 863-865 MHz transmission
• Supports an unlimited amount of receivers »xepton-NX RX«
• 8 selectable channel groups
• Signal range of up to 80 m
• Digital transmission
• Encryptable transmission
• Can be powered with a portable USB power pack

Available accessories

• RX receiver A-5120-0
• RX-U stethoset receiver A-5125-0
• HSB-01 microphone-headset A-5270-0
• EBB-01 microphone-headset A-5271-0
• EHR-01 microphone-headset A-5272-0

xepton-NX TR Transmitter

Controls and displays

How to use

Power ON / OFF Use the ON/OFF switch to switch the device on. The LC- display will light up and the current setup as well as the battery status are shown. The device is ready for use after 3 seconds. After 8 seconds the display goes out. It lights up again when an entry is made and goes out again after 8 seconds. Use the ON/OFF switch again to switch the device off.

Channel group selection Switch the device on and press the MODE-button for 3 seconds.
The symbol »GRP« in the display will blink. Select a channel of 0-7 by pressing the « and »« buttons. After the selection, wait for 3 seconds to set the selected channel number. Transmitters and receivers must be set to the same channel number if they are to communicate with each other. Please note: The symbols for a battery, as well as »MASTER« and »TALK« are always visible in the display. These can be ignored.

Volume up / down The volume can be adjusted through 6 levels from muted to maximum. On the powe-red-up device, press the » « and » « buttons to adjust the volume as desired.

Monitoring function On / Off

The monitoring function enables you to hear your own voice over the system. Proceed as follows if you wish to activate the monitoring function: On the powered-up device, press and hold the MODE-button for 3 seconds. The sym-bol »GRP« in the display will blink. Press the MODE button once. The letters »SO« or »SF« blink. By using the and buttons, select »SO« to activate the monitoring function or »SF« to deactivate it. After the selection, wait for 3 seconds to set the selected function.

Please note: The default setting is »SF« (monitoring deactivated).

Microphone sensitivity The microphone sensitivity can be adjusted through 5 levels according to environmental requirements: On the powered-up device, press and hold the MODE button for 3 seconds. The symbol »GRP« in the display will blink. Press the MODE button two times. The »C1« symbol in the display blinks. By using the and buttons, select between C1 (low sensitivity) and C5 (high sensitivity).

Audio output high / low Apart from the volume control, it is possible to adjust the basic audio output level. A higher audio output will raise the maximum volume – this might be required in noisy surroundings.
On the powered-up device, press and hold the MODE button for 3 seconds. The sym-bol »GRP« in the display will blink.
Press the MODE button three times. The »UH« symbol is shown in the display. By using the buttons, select UH (high output) or UL (normal output). After the se-lection, wait for 3 seconds to set the selected output level.

Please note: Selecting »UH« can cause white noise and should only be used in loud environments. We recommend the default setting »UL«.

Transmission power

The setting of the transmitting power affects the radio signal range. On the powered-up device, press and hold the MODE-button for 3 seconds. The sym-bol »GRP« in the display will blink. Press the MODE button four times. By using the buttons, select »P1« for the lowest transmission power and »P7« for the highest. After the selection, wait for 3 seconds to set the selected transmission power level.

Input level switch

This switch controls the input level of the 2 audio input connectors on the rear panel. Depending on the strength of the input signal, the signal can be amplified or attenuated by 10dB if necessary. When the switch is in the center position »N« (neutral), no change in level is applied.

Power supply

The transmitter is powered over the USB connection. The device can be powered by a regular USB powerpack for mobile phones and can hereby be used in a portable manner. Connect the powerpack to the USB connector on the rear of the device. The power consumption of the device is approx. 200mA.

Assignment of the connection sockets

Encryption

If the use of Xepton-NX requires discretion, such as in court buildings or during private sessions, the communication between transmitter and receiver can be encrypted. Other Xepton-NX devices can then no longer participate in the communication. For this purpose, basic settings on the involved devices must be changed – please contact your authorized AUDIOropa dealer.

Specifications

• Device type: Transmitter (unidirectional)
• Dimensions: 45 x 220 x 220 mm (H x W x D)
• Weight: 1360 g
• Transmission frequency: 863-865 MHz
• Transmission power: 10 mW maximum
• Latency: < 50 ms
• Frequency response: 100 Hz bis 14 kHz (unidirectional)
• Power: USB 5V/DC / 1A
• Power consumption: 200 mA
• Range: up to 80 m

Conformity

This device satisfies the following EU directives:

•  2011 / 65 / EC RoHS-directive
• 2012 / 19 / EC WEEE-directive
• 2014 / 53 / EC RED-directive

Compliance with the directives listed above is confirmed by the CE seal on the device. The complete CE compliance declaration is available on the internet at www.humantechnik.com/service Specifications subject to change.

Maintenance and care

All »xepton-NX«-devices do not require any maintenance. If they become dirty, simply wipe them clean with a soft, damp cloth. Never use spirits, thinners or other organic solvents. Do not expose them to full sunlight. In addition, they must be protected against excessive heat, moisture and severe mechanical shocks.

Note: These products are not protected against splash water. Do not place any containers filled with water, such as flower vases, or anything with an open flame, such as a lit candle, above or near the products.

Warranty

All »xepton-NX«-devices are very reliable products. Should a malfunction occur despite the unit having been set up and operated correctly, please contact your dealer or the manufacturer directly. This warranty covers the repair of the product and returning it to you free of charge. It is recommended that you send in the product in its original packaging, so keep the packaging for the duration of the warranty period. The warranty does not apply to damage caused by incorrect handling or attempts to repair the unit by unauthorised persons (destruction of the seal on the unit). Repairs will only be carried out under warranty if the completed warranty card is returned accompanied by a copy of the dealer’s invoice/till receipt. Always specify the product serial number in any event.

Disposal of used electrical and electronic units (applicable in the countries of the European Union and other European with a separate collection system). The symbol on the product or the packaging indicates that this product is not to be handled as ordinary household waste but has to be returned to a collecting point for the recycling of electrical and electronic units. You protect the environment and health of your fellow man by the correct disposal of this product. Environment and health are endangered by incorrect disposal. Material recycling helps to reduce the consumption of raw material. You will receive further information on the recycling of products from your local community, our communal disposal company or your local dealer.

References

• Willkommen
• Service

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>