AVEO ENGINEERING AVE-EMB-IM EyeBeam MB Titania Multicolor Light Installation Guide
- June 6, 2024
- AVEO ENGINEERING
Table of Contents
- AVEO ENGINEERING AVE-EMB-IM EyeBeam MB Titania Multicolor Light
- INSTALLATION MANUAL EyeBeam MB Titania
- DOC.NO: AVE-EMB-IM
- Part 0 Manual Administration
- Part 1 Installation Data
- 1.2 Operating Instructions
- 1.3 Installation Schematic / Wiring Diagram
- 1.4 Control & Power Inputs
- 1.5 Technical Specification
- 1.6 Technical Drawing
- MOUNTING HOLE
- Wiring Chart
- 1.8 Optic Simulation
- 1.11Testing of the Light Before Installation
- 1.12 Notes on Installation
- 1.13 Continues Airworthiness Information
- 1.14 RoHS Compliance Statement Scope
- 1.15 EU REACH Regulation (EC) No. 1907/2006
- Read More About This Manual & Download PDF:
- References
- Read User Manual Online (PDF format)
- Download This Manual (PDF format)
AVEO ENGINEERING AVE-EMB-IM EyeBeam MB Titania Multicolor Light
Installation Guide
INSTALLATION MANUAL EyeBeam MB Titania
DOC.NO: AVE-EMB-IM
Aveo Engineering Group, s.r.o. All rights reserved. The information contained
within this document must not be disclosed, copied or reproduced in whole or
in part without prior written permission from
Aveo Engineering Group, s.r.o.
Part 0 Manual Administration
0.1 Document Approval
This document has been established in accordance with an alternative
procedureto DOA approved under EASA AP429.
This installation manual is applicable for part numbers:
- EyeBeam MB Titania – Black AVE-EMBILW-TB0
- EyeBeam MB Titania II – White/Red – Silver AVE-EMBILWR-TS0
- EyeBeam MB Titania II – White/Red – Black AVE-EMBILWR-TB0
- EyeBeam MB Titania II – White/Green – Silver AVE-EMBILWG-TS0
- EyeBeam MB Titania II – White/Green – Black AVE-EMBILWG-TB0
- EyeBeam MB Titania IV – Silver AVE-EMBILRGBW-TS0
- EyeBeam MB Titania IV – Black AVE-EMBILRGBW-TB0
0.2 Amendment Record Procedure
The master copy of this document shall be kept electronically as a read only
document under the control of Aveo Engineering Group, s.r.o. as Master Copy.
ALL amendments to this manual will initiate a raise of issue.
ALL raises of issue will be given a sequential numeric issue ident
sequentially from 01 to 99 in Table 01 – Issue No: Column– Initial Issue of
Document will
be “01” ALL Issues of this document will be approved by Head of DO
Issue No. | Details | Date | Affected Pages |
---|---|---|---|
01 | Initial Issue | 23.Oct.2020 | ALL |
02 | Installation note addition EU REACH Regulation | 14.Apr.2021 | 8, 12 |
13
| | |
Table 01: Document Amendment Record Table
0.3 Affected Pages Procedure
ALL pages affected by ANY raise of issue of this document will be listed in
Table 01 – Affected Pages Column.
The reason(s) for ALL raise of issue and description of change due to raise of
issue will be provided for ALL raises of issue in Table 01 – Details Column.
Changes from the previous issue are highlighted by YELLOW HIGHLIGHTING over
new content. AND YELLOW HIGHLIGHTING AND CROSSING OUT of
deleted content. Example (CROSSING OUT)
Part 1 Installation Data
1.1 EyeBeam MB Titania
EyeBeam MB Titania™ is interior swivel LED light. It is available in 3 different versions – single color, dual color and four color. All versions have black or natural anodized finish.
- EyeBeam MB Titania – Silver AVE-EMBILW-TS0
- EyeBeam MB Titania – Black AVE-EMBILW-TB0
- EyeBeam MB Titania II – White/Red – Silver AVE-EMBILWR-TS0
- EyeBeam MB Titania II – White/Red – Black AVE-EMBILWR-TB0
- EyeBeam MB Titania II – White/Green – Silver AVE-EMBILWG-TS0
- EyeBeam MB Titania II – White/Green – Black AVE-EMBILWG-TB0
- EyeBeam MB Titania IV – Silver AVE-EMBILRGBW-TS0
- EyeBeam MB Titania IV – Black AVE-EMBILRGBW-TB0
1.2 Operating Instructions
Operating Voltage range is 9-36VDC. When installed on the aircraft, using the aircraft’s power (14 or 28 volts), the light will be at its maximum intensity.
AVE-EMBILWR-TS0
AVE-EMBILWR-TB0
AVE-EMBILWG-TS0
AVE-EMBILWG-TB0
AVE-EMBILRGBW-TS0 AVE-EMBILW-TS0
AVE-EMBILRGBW-TB0 AVE-EMBILW-TB0
1.3 Installation Schematic / Wiring Diagram
1.4 Control & Power Inputs
BLACK – Negative power supply line (ground)
RED – Positive power supply line
BLUE – Connecting to GND turns the DIM/WHITE LIGHT ON
Disconnecting from GND turns the LIGHT OFF
1.5 Technical Specification
Electronic specification – Ambient temperature (25°C):
Operating voltage range: 9-36V DC
Dimensions: See section #1.6 – Technical Drawing
Performance:
FULL Input current: 0.139A @14V
0.085A @28V
DIM Input current: 0.006A @14V
0.006A @28V
FULL Input power: 1.9W @14V (typ)
2.38W @28V (typ)
DIM Input power: 0.084W @14V (typ)
0.168W @28V (typ)
Operating temperature: -40°C to +85°C / -40°F to +185°F
Weight: 3.7 oz / 105 g
1.6 Technical Drawing
MOUNTING HOLE
Wiring Chart
Use diagram below defining the wiring size depending on the current and the
wire length.
Make sure you add up the current for all connected lights. If current is not
given, then divide the power by the voltage.
1.8 Optic Simulation
Standard lens
White LED
Intensity: 780 cd
Beam angle: 25°
1.9 Equipment Limitation
EyeBeam MB Titania™ should only be powered by 9-36VDC
1.10 Care and Cleaning of your Aveo Engineering Aviation Lights
When you receive your Aveo Engineering Aviation Lights, they will have been
factory polished and ready to install on the aircraft.
If the lights require a deeper cleaning, they should be polished with a
quality lamb’s wool sheet and can also be used for deeper polishing. Under no
circumstances
should any petroleum based product be used to clean the lights.
1.11Testing of the Light Before Installation
All Aveo Aviation lights undergo rigorous testing prior to being released from
our engineering manufacturing department. This testing involves a burn-in time
as well as other function testing. No light is released for sale without
undergoing this extensive operational testing.
When you receive the EyeBeam MB Titania™ light, and wish to test the function
of the light prior to installation on your aircraft, please note the
following:
Testing of the Light Before Installation All Aveo Aviation lights undergo
rigorous testing prior to being released from our engineering manufacturing
department. This testing involves a burn-in time
as well as other function testing. No light is released for sale without
undergoing this extensive operational testing.
When you receive the EyeBeam MB Titania™ light, and wish to test the function
of the light prior to installation on your aircraft, please note the
1.12 Notes on Installation
Mount EyeBeam on the wall as it is described on the image below.ollowing:
1.13 Continues Airworthiness Information
Periodic Inspection Procedure for EyeBeam MB Titania series.
The EyeBeam MB Titania™ lights should always be checked for proper operation
during preflight. This procedural information is already provided in all
general aviation aircraft flight manuals.
The lights should be visually inspected for general condition, proper
operation, and correct installation at each annual and/or 100 hours
inspection. In addition refer to section 1.10 of installation manual for
detailed cleaning instructions.
1.14 RoHS Compliance Statement Scope
This statement clarifies Aveo Engineering’s compliance with European Union
Directive 2015/863/EU on the restriction of the use of certain hazardous
substances in electrical and electronic equipment (“RoHS”) that took effect on
June 4, 2015.
The RoHS Directive restricts the sale of electronic equipment containing
certain hazardous substances in the European Union including:
1.15 EU REACH Regulation (EC) No. 1907/2006
Aveo Engineering declares that no chemicals are produced and that none of the
chemicals used during the production process or needed for the product
maintenance or service, is listed on the current European Chemicals Agency’s
Candidate list of Substances of Very High Concern for Authorization.
Read More About This Manual & Download PDF:
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>