HORIZON Blade 61256 BLH 120 S2 RTF BNF with Safe Instruction Manual

120 S2

Instruction Manual

NOTICE
All instructions, warranties, and other collateral documents are subject to change at the sole discretion of Horizon Hobby, LLC. For up-to-date product literature, visit  orizonhobby.com or towerhobbies.com and click on the support or resources tab for this product.
Meaning of Special Language
The following terms are used throughout the product literature to indicate various levels of potential harm when operating this product:
WARNING: Procedures, which if not properly followed, create the probability of property damage, collateral damage, and serious injury OR create a high probability of superfi cial injury.
CAUTION: Procedures, which if not properly followed, create the probability of physical property damage AND a possibility of serious injury.
NOTICE: Procedures, which if not properly followed, create a possibility of physical property damage AND a little or no possibility of injury.
WARNING: Read the ENTIRE instruction manual to become familiar with the features of the product before operating. Failure to operate the product correctly can result in damage to the product, and personal property and cause serious injury. This is a sophisticated hobby product. It must be operated with caution and common sense and requires some basic mechanical ability. Failure to operate this Product in a safe and responsible manner could result in injury or damage to the product or other property. This product is not intended for use by children without direct adult supervision. Do not use incompatible components or alter this product in any way outside of the instructions provided by  Horizon Hobby, LLC. This manual contains instructions for safety, operation, and maintenance. It is essential to read and follow all the instructions and warnings in the manual, prior to assembly, setup or use, in order to operate correctly and avoid damage or serious injury.
Age Recommendation: Not for children under 14 years. This is not a toy.

Safety Precautions and Warnings

• Always keep a safe distance in all directions around your model to avoid collisions or injury. This model is controlled by a radio signal subject to interference from many sources outside your control. Interference can cause momentary loss of control.
• Always operate your model in open spaces away from full-size vehicles, traffi c, and people.
• Always carefully follow the directions and warnings for this and any optional support equipment (chargers, rechargeable battery packs, etc.).
• Always keep all chemicals, small parts, and anything electrical out of the reach of children.
• Always avoid water exposure to all equipment, not specifi cally designed and protected for this purpose. Moisture causes damage to electronics.
• Never place any portion of the model in your mouth as it could cause serious injury or even death.
• Never operate your model with low transmitter batteries.
• Always keep aircraft in sight and under control.
• Always move the throttle fully down at rotor strike.
• Always use fully charged batteries.
• Always keep the transmitter powered on while the aircraft is powered.
• Always remove batteries before disassembly.
• Always keep moving parts clean.
• Always keep parts dry.
• Always let parts cool after use before touching.
• Always remove batteries after use.
• Never operate aircraft with damaged wiring.
• Never touch moving parts.

Specifications

Box Contents

• Blade 120 S2
• 500mAh 1S 3.7V 25C Li-Po Battery
• 1S Li-Po USB Charger
• MLP6DSM SAFE 6 Channel Transmitter (RTF Only)
• 4 AA Batteries (RTF Only)

First Flight Preparation

• Remove and inspect contents
• Begin charging the fl right battery
• Install the batteries in the transmitter (RTF only)
• Program your computer transmitter (BNF only)
• Install the fl right battery in the helicopter (once it has been fully charged)
• Bind your transmitter (BNF only)
• Familiarize yourself with the controls
• Find a suitable area for fl ying

Flying Checklist

• Always turn the transmitter on fi rst
• Plug the fl ight battery into the lead from the ESC
• Allow the receiver and ESC to initialize and arm properly
• Fly the model
• Land the model
• Unplug the fl ight battery from the ESC
• Always turn the transmitter off last

Charging Warnings

CAUTION: All instructions and warnings must be followed exactly. Mishandling of Li-Po batteries can result in a fi re, personal injury and/or property damage.

• NEVER LEAVE CHARGING BATTERIES UNATTENDED.
• NEVER CHARGE BATTERIES OVERNIGHT.
• By handling, charging or using the included Li-Po battery, you assume all risks associated with lithium batteries.
• If at any time the battery begins to balloon or swell, discontinue use immediately. If charging or discharging, discontinue and disconnect. Continuing to use, charge or discharge a battery that is ballooning or swelling can result in fi re.
• Always store the battery at room temperature in a dry area for best results.
• Always transport or temporarily store the battery in a temperature range of 40–120º F (5–49° C).
• Do not store battery or model in a car or direct sunlight. If stored in a hot car, the battery can be damaged or even catch fi re.
• Always charge batteries away from fl dimmable materials.
• Always inspect the battery before charging
• Always disconnect the battery after charging, and let the charger cool between charges.
• Always constantly monitor the temperature of the battery pack while charging.
• ONLY USE A CHARGER SPECIFICALLY DESIGNED TO CHARGE LI-PO BATTERIES. Failure to charge the battery with a compatible charger may cause a fi re resulting in personal injury and/or property damage.
• Never discharge Li-Po cells to below 3V under load.
• Never cover warning labels with hook and loop strips.
• Never charge batteries outside recommended levels.
• Never charge damaged batteries.
• Never attempt to dismantle or alter the charger.
• Never allow minors to charge battery packs.
• Never charge batteries in extremely hot or cold places (recommended between 40–120° F or (5–49° C) or place in direct sunlight.

Battery Charging

NOTICE: Charge only batteries that are cool to the touch and are not damaged. Look at the battery to make sure it is not damaged e.g., swollen, bent, broken or punctured.

1. Insert the charger into a USB port.
2. Properly connect the battery to the charger lead.
3. Always disconnect the fl right battery from the charger immediately upon completion of charging.

CAUTION: Only use chargers specifi cally designed to charge the included Li-Po battery. Failure to do so could result in fi re, causing injury or property damage.
CAUTION: Never exceed the recommended charge rate.
LED Indications
When you make the connection successfully, the LED on the charger turns solid red, indicating charging has begun. Charging a fully discharged (not over- discharged) 500mAh
the battery takes approximately 60 minutes. The light goes off when the charge is complete.
CHARGING (Solid Red)
MAX CHARGE (OFF)
CAUTION: Once charging is complete, immediately remove the battery. Never leave a battery connected to the charger.

Installing the Transmitter Batteries (RTF)

Replace the transmitter batteries when the transmitter beeps.

Transmitter Setup (BNF)
Program your transmitter before attempting to bind or fly the helicopter. Transmitter programming values are shown below for the Spektrum DX6i, DX7s, DX6, DX7, DX8, DX9 and DX18.
The fi les for models using Spektrum™ transmitters with Spektrum AirWare™ software are also available for download online at www.spektrumrc.com. Your helicopter is also compatible with Spektrum DXe radios with software version 1.3 or higher. Use the directions below to reverse channel 6, or use the appropriate programming cable and the PC or mobile app to program the DXe. We recommend downloading the Blade 120 S2 DXe model setup available at www.spektrumrc.com.
If you are programming your DXe using the PC or mobile app, make sure the “Transmitter Channels” value is set to the default of 7. If for any reason this value is changed to
9, the 120 S2 will bind to the DXe, but will not respond to control inputs. If your DXe was included in another Blade® Ready To Fly (RTF) helicopter, the transmitter software will have to be updated using the appropriate programming cable and either the PC or mobile app available at www.spektrumrc.com. Please note, that the switch confi guration used for DXe transmitters included with the Blade 230 S RTF and Micro AH64 Apache™ RTF varies from the standard DXe layout.

DXe
To use the DXe transmitter with the Blade 120 S2, channel 6 must be reversed. To reverse channel 6:

1. While powering on the DXe, hold the left and right sticks in the top-inside corners as shown.

2. Re-center the sticks after the transmitter beeps. The LED will fl ash slowly.

3. To select a channel to reverse, move the right stick to the left or right and allow it to re-center. Move the stick to the right to select the next channel. Move the stick to the
   left to select the previous channel. The LED will fl ash rapidly corresponding to the channel selected, as shown in the table. Select channel 6.

4. To reverse the selected channel, move the right stick up or down. The LED will change color to indicate the new channel direction.

5. The LED will fl ash Orange to indicate the channel is normal. The LED will fl ash Red to indicate the channel is reversed.

6. To store the changes, power off the DXe.

CAUTION: During the subsequent power-up, always verify the throttle direction is correct and keep clear of the motor and rotor blades. Failure to do so may result in injury or damage to the product.
After reversing channel 6, bind the transmitter and helicopter normally. Flight modes are controlled by the Flight Mode switch. Panic Mode is controlled by the Bind/Panic/Trainer button. Once bound, the LED in the helicopter should glow green blue or red, depending on the fl light mode selected. If the LED glows green in FM-0 mode or blue in FM-1/FM-2 modes, channel 6 has not been reversed correctly. Use the directions above to reverse channel 6. If the LED fl ashes red, replace the fl right battery with a fully charged battery.

DX6i

**Expo*
Channel| Direction| | THRO| 100/100| | AILE| 0| 100| INH
THRO| N| | AILE| 100/100| 1| 75| INH
AILE| N| | ELEV| 100/100| | ELEV| 0| 100| INH
ELEV| N| | RUDD| 100/100| 1| 75| INH
RUDD| N| | GEAR| 100/100| | RUDD| 0| 100| INH
GEAR| R| | PITC| 100/100| 1| 75| INH
FLAP| N| | FLAPS| | Mixing
Modulation Type| | | FLAP| ELEV| | MIX 1| ACT
AUTO DSMX-ENABLE| | NORM| 100| 0| | GEAR > GEAR| ACT
LAND| 100| 0| | RATE| D 0%| U –100%
D/R COMBI| | SW| GEAR| TRIM – INH
D/R SW| AILE| MIX 2| ACT
Timer| GEAR > GEAR| ACT
Down Timer| 5:00| RATE| D 0%| U +100%
Switch| THR CUT**| SW| ELE D/R| TRIM – INH

Panic Mode Operation
Gyro Switch:
Pos 0 = Panic Mode Off
Pos 1 = Panic Mode On
Flight Mode Operation
Gear Sw: Pos 0, Elev D/R Sw: 0 or 1 = Stability, Low-Angle Mode
Gear Sw: Pos 1, Elev D/R Sw: 0 = Stability, High-Angle Mode
Gear Sw: Pos 1, Elev D/R Sw: 1 = Agility Mode

DX7s

SYSTEM SETUP

Model Type| ACRO
SW Select
Trainer| Aux 1
Flap| Gear
All Others| INH

Panic Mode Operation
Trainer/Bind Button
Pressed = Panic Mode On
Released = Panic Mode Off

FUNCTION LIST

Servo Setup
Chan| Travel| Reverse| | Chan| Travel| Reverse
THR| 100/100| Normal| GER| 100/100| Normal
AIL| 100/100| Normal| AX1| 100/100| Reverse
ELE| 100/100| Normal| AX2| 100/100| Normal
RUD| 100/100| Normal|
D/R & Expo| | D/R & Expo
Chan| Switch Pos (FLAP)| D/R| Expo| Chan| Switch Pos (FLAP)| D/R| Expo
AILE| 0| 100/100| 0| RUDD| 0| 100/100| 0
1| 100/100| 0| 1| 100/100| 0
2| 75/75| 0| 2| 75/75| 0
ELEV| 0| 100/100| 0| | Timer
1| 100/100| 0| Mode| Count Down
2| 75/75| 0| Time| 5:00 Tone
Throttle Cut| | Start| Throttle Out
Switch| Mix 1| Pos| 25%

Flight Mode Operation
FLAP Sw: Pos 0 = Stability, Low-Angle Mode
Pos 1 = Stability, High-Angle Mode
Pos 2 = Agility Mode

• Use of “Expo” is not necessary for successful fl ight of the 120 S2. The pilot may adjust this setting to tailor the sensitivity of the helicopter around neutral if desired.

DX8

SYSTEM SETUP

Model Type| ACRO
SW Select
Trainer| Aux 1
F Mode| Gear
All Others| INH

Panic Mode Operation
Trainer/Bind Button
Pressed = Panic Mode On
Released = Panic Mode Off

FUNCTION LIST

Servo Setup
Chan| Travel| Reverse| | Chan| Travel| Reverse
THR| 100/100| Normal| GER| 100/100| Normal
AIL| 100/100| Normal| AX1| 100/100| Reverse
ELE| 100/100| Normal| AX2| 100/100| Normal
RUD| 100/100| Normal|
D/R & Expo| | D/R & Expo
Chan| Switch Pos (AIL D/R)| D/R| Expo| Chan| Switch Pos (AIL D/R)| D/R| Expo

AILE

| 0| 100/100| 0|

RUDD

| 0| 100/100| 0
1| 100/100| 0| 1| 100/100| 0
2| 75/75| 0| 2| 75/75| 0
ELEV| 0| 100/100| 0| | Timer
1| 100/100| 0| Mode| Count Down
2| 75/75| 0| Time| 5:00 Tone
Throttle Cut| | Start| Throttle Out
Switch| Mix 1| Pos| 25%

Flight Mode Operation
F MODE Sw: Pos 0 = Stability, Low-Angle Mode
Pos 1 = Stability, High-Angle Mode
Pos 2 = Agility Mode

DX6, DX6e, DX7 (Gen 2), 8e, DX9, DX18, iX12, iX20

Throttle Cut

Position                              130

Switch                             Switch H

0 1

1 Throttle| N/A| | D/R & Expo
2 Aileron| N/A| | ****

Chan

| Switch (F) Pos| ****

D/R

| ****

**Expo***

3 Elevator| N/A| ****

DX6

| DX7, 9,

18

4 Rudder| N/A
5 Gear| B| | ****

AILE

| 0| 0| 100/100| 0
6 AUX 1| I| | 1| 100/100| 0
| 1| 2| 75/75| 0

ELEV

| 0| 0| 100/100| 0
| 1| 100/100| 0
1| 2| 75/75| 0

RUDD

| 0| 0| 100/100| 0
| 1| 100/100| 0
1| 2| 75/75| 0
Timer

Mode| Count Down
Time| 5:00
Start| Throttle Out
Over| 25%
One Time| Inhibit

Flight Mode Operation
Sw B: Pos 0 = Stability, Low-Angle Mode
Pos 1 = Stability, High-Angle Mode
Pos 2 = Agility Mode

• Use of “Expo” is not necessary for successful fl right of the 120 S2. The pilot may adjust this setting to tailor the sensitivity of the helicopter around neutral if desired.

Installing the Flight Battery

1. Lower the throttle stick to the lowest position (A) and center all trims.

2. Set the fl night mode switch to Stability, Low Bank Angle Mode (FM-0)

3. Power ON the transmitter (B).

4. Slide the fl right battery fully into the mount of the helicopter frame (C).

5. Connect the power lead to the battery (D), noting the correct polarity.
   CAUTION: Connecting the battery to the control board with reversed polarity will cause damage to the control board, the battery, or both. Damage caused by incorrectly connecting the battery is not covered under warranty.

6. Keep the aircraft from moving. The LED quickly fl ashes red followed by a quick green fl ash and then cycles red, green, blue, and red, indicating initialization is complete.

After initialization is complete:

• If the aircraft is bound correctly to the transmitter, the LED will change to show the currently selected fl right mode.
• If the LED on the control board fl ashes blue rapidly, indicating the aircraft is in bind mode, proceed to the Transmitter and Receiver Binding section to bind the aircraft and transmitter.
• If the LED fl ashes blue slowly, the fl right controller lost communication with the transmitter.
• If the LED fl ashes red, the fl right controller has hit the low voltage cutoff (LVC). Replace the fl light battery with a fully charged battery.

CAUTION: Always disconnect the Li-Po battery from the aircraft when not fl ying to avoid over-discharging the battery. Batteries discharged to a voltage lower than the lowest approved voltage may become damaged, resulting in loss of performance and potential fi re when batteries are charged.

Transmitter and Receiver Binding

Your RTF transmitter comes prebound to the model. If you need to re-bind, follow the directions below.
MLP6DSM Binding Procedure (RTF)

1. Disconnect the fl ight battery from the helicopter.
2. Center all trims on your transmitter.
3. Power off the transmitter and move the throttle stick to the down/off position.
4. Connect the fl ight battery in the helicopter, and keep the helicopter from moving. The LED on the control board continually fl ashes blue after the aircraft initializes, indicating the control board is in bind mode.
5. Push in and hold down the left stick* while powering on the transmitter (you will hear a ‘click’).
6. Release the left stick. The transmitter will beep and the power LED will blink.
7. The helicopter is bound when the LED on the control board is solid (not blinking).
8. Disconnect the fl ight battery and power the transmitter off.

• The trigger switch may also be used for the binding procedure.
  If you encounter problems, obey binding instructions and refer to the troubleshooting guide for other instructions. If needed, contact the appropriate Horizon Product Support offi ce.

To bind or re-bind your helicopter to your chosen transmitter, follow the directions below.
General Binding Procedure (BNF)

1. Disconnect the fl right battery from the helicopter.
2. Refer to the Transmitter Setup Table to correctly set up your transmitter.
3. Lower the throttle stick to the lowest position and center all trims on your transmitter.
4. Power off the transmitter and move all switches to the 0 positions. Move the throttle to the low/off position.
5. Connect the fl right battery to the control board. The control board LED rapidly fl ashes blue, indicating it is in bind mode.
6. Put the transmitter into bind mode while powering on the transmitter.
7. Release the bind button/switch after 2–3 seconds. The helicopter is bound when the LED on the receiver turns solid.
8. Disconnect the fl right battery and power the transmitter off.

CAUTION: When using a Futaba® transmitter with a Spektrum™ DSM2® module, you must reverse the throttle channel and re-bind. Refer to your Spektrum module manual for binding and failsafe instructions. Refer to your Futaba transmitter manual for instructions on reversing the throttle channel.

RTF Transmitter Controls

When pressed down, trim buttons make a sound that increases or decreases in pitch at each pressing. The middle or neutral trim position is heard as a middle tone in the pitch range of the sounds. The end of the control range is sounded by a series of beeps.
Dual Rate Selection
The control sensitivity can be changed by pressing and releasing the right control stick. The LED on the transmitter will show solid for high sensitivity (default) and fl ashing for
low sensitivity.

Throttle (Up/Down)_

Control Tests

Test the controls prior to the fi first fl right to ensure the servos, linkages, and parts operate correctly. Ensure the throttle is in a low position when doing the control tests.

Understanding the Primary Flight Controls
If you are not familiar with the controls of your 120 S2, take a few minutes to familiarize yourself with them before attempting your fi rst fl ight.

Flying the 120 S2

Consult your local laws and ordinances before choosing a location to fl y your aircraft. We recommend fl ying your aircraft outside in calm winds (3 MPH or less) or inside a large gymnasium. Always avoid fl lying near houses, trees, wires, and buildings. You should also be careful to avoid fl ying in areas where there are many people, such as busy parks, schoolyards or soccer fi eds. It is best to fl y from a smooth fl at the surface as this will allow the model to slide without tipping over. Keep the helicopter approximately 2 ft (600mm) above the ground. Keep the tail pointed toward you during initial fl rights to keep the control orientation consistent. Releasing the stick while in Stability, low bank angle mode or Stability, high bank angle mode will allow the helicopter to level itself, and activating the Panic Switch will level the helicopter quickly. If you become disoriented, slowly lower the throttle stick to land softly. During initial fl rights, only attempt hovering the model in one spot and takeoff and landing.
Takeoff
Place the model onto a fl at, a level surface free of obstacles and walk back 30 feet (10 meters). Slowly increase the throttle until the model is approximately 2 ft. (600mm)
off the ground and check the trim so the model fl is as desired. Once the trim is adjusted, begin fl ying the model. The typical fl right time for the included battery is approximately 6 minutes.
Hovering
Making small corrections on the transmitter, try to hold the helicopter in one spot. If fl ying in calm winds, the model should require almost no corrective inputs. After moving the cyclic stick and returning it to the center the model should level itself. The model may continue to move due to inertia. Move the cycle stick in the opposite direction to stop the movement. Do not use the trims on the transmitter to eliminate drift. If the helicopter does not hold a reasonable hover in calm conditions, perform the Drift Calibration.
After you become comfortable hovering, you can progress into fl ying the model to different locations, keeping the tail pointed towards you at all times. You can also ascend and
descend using the throttle stick. Once you’re comfortable with these maneuvers, you can attempt fl ying with the tail in different orientations. It is important to keep in mind that the fl eight control inputs will rotate with the helicopter, so always try to picture the control inputs relative to the nose of the helicopter. For example, the forward will always drop the nose of the helicopter.
Low Voltage Cutoff (LVC)
LVC decreases the power to the motors when the battery voltage gets low. When the motor power decreases and the red LED on the ESC fl ashes, land the aircraft immediately
and recharge the fl right battery. LVC does not prevent the battery from over- discharge during storage.
NOTICE: Repeated fl Ying to LVC will damage the battery.
Landing
To land, slowly decrease the throttle while in a low-level hover. After landing, disconnect and remove the battery from the aircraft after use to prevent trickle discharge. Fully charge your battery before storing it. During storage, make sure the battery charge does not fall below 3V per cell. Flight Modes
Stability, Low Bank Angle Mode (FM-0): The receiver LED shows solid green. This fl night mode allows a low bank angle and slower fl right speed. When the cyclic stick is released the model will self-level.
Stability, High Bank Angle Mode (FM-1): The receiver LED shows solid blue. This fl night mode allows a high bank angle and faster fl right speed. When the cyclic stick is released the model will self-level.
Agility Mode (FM-2): The receiver LED shows solid red. The bank angle is not limited. When the cyclic stick is released the model will not self-level.

Drift Calibration

The helicopter has been calibrated in the factory before shipment, but it is possible that a crash will cause mechanical distortion of the frame, resulting in a slight drift in Stability mode. In this situation, please follow the calibration procedure. Before beginning the calibration procedure, fully charge the fl right battery and ensure the helicopter and transmitter are bound properly, per the binding instructions.

To Calibrate the Blade 120 S2:

1.  After initialization, move the transmitter sticks to the bottom, and outside corners, as shown in the illustration. When the red and blue LEDs on the main fl light control board glow solid, calibration mode is active.
   

2. Release the sticks.

3. Slowly advance the throttle to bring the helicopter into a low hover. The red and blue LEDs fl ash continuously to indicate the calibration process has begun. Hold the hover for approximately 15 seconds, using as little control input as possible to keep the helicopter steady.

4. Land the helicopter by slowly lowering the throttle.

5. After landing, press the bind/panic button to complete the calibration process. The LED will show solid blue.

Post-Flight Inspection and Maintenance Checklist

Ball Links

| Make sure the plastic ball link holds the control ball, but is not tight (binding) on the ball. When a link is too loose on the ball, it can separate from the ball during flight and cause a crash. Replace worn ball links before they fail.
---|---
Cleaning| Make sure the battery is not connected before cleaning. Remove dust and debris with a soft brush or a dry, lint-free cloth.
Bearing s| Replace bearings when they become notchy (sticky in places when turning) or draggy.
Wiring| Make sure the wiring does not contact moving parts. Replace damaged wiring and loose connectors.
Fasteners| Make sure there are no loose screws, other fasteners or connectors. Do not over-tighten metal screws in plastic parts. Tighten screws so the parts are mated together, then turn the screw only 1/8th of a turn more.

Rotors

| Make sure there is no damage to rotor blades and other parts which move at high speed. Damage to these parts includes cracks, burrs, chips or scratches. Replace damaged parts before flying. Verify both main rotor blades have the correct and equal tension in the blade grips. When the helicopter is held up sideways, the main blades should support their own weight. When the helicopter is shaken lightly, the blades should fall.
Tail| Inspect the tail rotor for damage and replace if necessary. Inspect the tail boom for any damage and replace if necessary.

Mechanics

| Inspect the mainframe and landing gear for damage and replace if necessary. Check the main shaft for vertical play and adjust the locking collar if necessary. Verify that the main gear mesh is correct and that no tight spots exist in the 360-degree rotation. Inspect all wires for damage and replace as necessary.

Troubleshooting Guide

Helicopter has reduced flight time or is underpowered

| Flight battery charge is low| Completely recharge the flight battery
Flight battery is damaged| Replace the flight battery and follow the flight battery instructions
Flight conditions might be too cold| Make sure the battery is warm (room temperature) before use
**** LED on receiver flashes rapidly and aircraft will not respond to the transmitter (during binding)| Transmitter too near aircraft during the binding process| Power off the transmitter. Move the transmitter a larger distance from the aircraft. Disconnect and reconnect the flight battery to the aircraft. Follow the binding instructions
Bind switch or button was not held while the transmitter was powered on| Power off transmitter and repeat bind process
Aircraft or transmitter is too close to large metal object, wireless source or another transmitter| Move aircraft and transmitter to another location and attempt binding again

**** LED on the receiver flashes rapidly and the helicopter will not respond to the transmitter (after binding)

| Less than a 5-second wait between first powering on the transmitter and connecting the flight battery to the helicopter| ****

Leave the transmitter powered on. Disconnect and reconnect the flight battery to the helicopter

The helicopter is bound to a different model memory

(ModelMatch™ transmitters only)

| Select the correct model memory on the transmitter. Disconnect and reconnect the flight battery to the helicopter
The flight battery or transmitter battery charge is too low| Replace or recharge batteries
Aircraft or transmitter is too close to large metal object, wireless source or another transmitter| Move aircraft and transmitter to another location and attempt connecting again

Helicopter vibrates or shakes in flight

| Damaged rotor blades, spindle, blade grips, main gear teeth or cracked main shaft.| Check main rotor blades, blade grips, main gear and main shaft for cracks, chips or missing teeth. Replace damaged parts. Replace bent spindle
Rotor head linkages not connected correctly| Connect the rotor head linkages to the short ball links on the swashplate
Model does not hold level/ Panic recovery does not level. Random movements in flight| ****

Vibration

| Verify the receiver is properly attached to the helicopter. Verify that no wires are contacting the receiver. Inspect and balance all rotating components. Verify the main shaft and tail rotor adapter are not damaged or bent. Inspect mechanics for broken or damaged parts and replace as necessary
Tail oscillation/wag or poor performance| Loose tail boom, damaged tail rotor, loose bolts, vibration| Verify that the boom is tight and completely inserted into the frame. Inspect the tail rotor for damage. Verify the tail motor mount is tight. Replace any damaged or worn components
**** Drift in calm winds| **** Vibration, damaged linkage, damaged servo| Under normal operation, the transmitter trims should not require adjustment and the center positions are memorized during initialization. If you find that trim adjustments are necessary after take off, verify the balance of all rotating components, ensure the linkages are not damaged and make sure the servos are in proper working condition. Perform the Drift Calibration procedure

Drift in wind

| ****

Normal

| The model will drift with the wind but should remain level in flight. Simply hold the cyclic stick in the necessary position to keep the model stationary. The model must lean into the wind to remain stationary, if the model remains level then it will drift with the wind
Severe vibration| Rotating component out of balance| Check the main shaft, tail rotor, main rotor blades, mainframe, and adapter for damage, replace as necessary. Vibration must be minimized for Panic Recovery and Return to Level functions to work properly

Exploded View

Parts List

Limited Warranty

What this Warranty Covers
Horizon Hobby, LLC, (Horizon) warrants to the original purchaser that the product purchased (the “Product”) will be free from defects in materials and workmanship at the date of purchase.
What is Not Covered
This warranty is not transferable and does not cover (i) cosmetic damage, (ii) damage due to acts of God, accident, misuse, abuse, negligence, commercial use, or due to improper use, installation, operation or maintenance, (iii) modifi cation of or to any part of the Product, (iv) attempted service by anyone other than a Horizon Hobby authorized service center, (v) Product not purchased from an authorized Horizon dealer, (vi) Product not compliant with applicable technical regulations, or (vii) use that violates any applicable laws, rules, or regulations. OTHER THAN THE EXPRESS WARRANTY ABOVE, HORIZON MAKES NO OTHER WARRANTY OR REPRESENTATION AND HEREBY DISCLAIMS ANY AND ALL IMPLIED WARRANTIES, INCLUDING, WITHOUT LIMITATION, THE IMPLIED WARRANTIES OF NON-INFRINGEMENT, MERCHANTABILITY, AND FITNESS FOR A PARTICULAR PURPOSE. THE PURCHASER ACKNOWLEDGES THAT THEY ALONE HAVE DETERMINED THAT THE PRODUCT WILL SUITABLY MEET THE REQUIREMENTS OF THE PURCHASER’S INTENDED USE.
Purchaser’s Remedy
Horizon’s sole obligation and purchaser’s sole and exclusive remedy shall be that Horizon will, at its option, either (i) service, or (ii) replace, any Product determined by Horizon to be defective. Horizon reserves the right to inspect any and all Product(s) involved in a warranty claim. Service or replacement decisions are at the sole discretion of Horizon. Proof of purchase is required for all warranty claims. SERVICE OR REPLACEMENT AS PROVIDED UNDER THIS WARRANTY IS THE PURCHASER’S SOLE AND EXCLUSIVE REMEDY.
Limitation of Liability
HORIZON SHALL NOT BE LIABLE FOR SPECIAL, INDIRECT, INCIDENTAL, OR CONSEQUENTIAL DAMAGES, LOSS OF PROFITS OR PRODUCTION, OR COMMERCIAL LOSS IN ANY WAY, REGARDLESS OF WHETHER SUCH CLAIM IS BASED ON CONTRACT, WARRANTY, TORT, NEGLIGENCE, STRICT LIABILITY, OR ANY OTHER THEORY OF LIABILITY, EVEN IF HORIZON HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES. Further, in no event, shall the liability of Horizon exceed the individual price of the Product on which liability is asserted. As Horizon has no control over use, setup, fi nal assembly, modifi cation or misuse, no liability shall be assumed nor accepted for any resulting damage or injury. By the act of use, setup, or assembly, the user accepts all resulting liability. If you as the purchaser or user are not prepared to accept the liability associated with the use of the Product, the purchaser is advised to return the Product immediately in new and unused condition to the place of purchase.
Law
These terms are governed by Illinois law (without regard to confl ICT of law principles). This warranty gives you specifi c legal rights, and you may also have other rights which vary from state to state. Horizon reserves the right to change or modify this warranty at any time without notice.
WARRANTY SERVICES
Questions, Assistance, and Services
Your local hobby store and/or place of purchase cannot provide warranty support or service. Once assembly, setup, or use of the Product has been started, you must contact your local distributor or Horizon directly. This will enable Horizon to better answer your questions and service you in the event that you may need any assistance. For questions or assistance, please visit our website at www.horizonhobby.com, submit a Product Support Inquiry, or call the toll-free telephone number referenced in the Warranty and Service Contact Information section to speak with a Product Support representative.
Inspection or Services
If this Product needs to be inspected or serviced and is compliant in the country you live and use the Product in, please use the Horizon Online Service Request submission process found on our website or call Horizon to obtain a Return Merchandise Authorization (RMA) number. Pack the Product securely using a shipping carton. Please note that original boxes may be included, but are not designed to withstand the rigors of shipping without additional protection. Ship via a carrier that provides tracking and insurance for lost or damaged parcels, as Horizon is not responsible for merchandise until it arrives and is accepted at our facility. An Online Service Request is available at http://www.horizonhobby.com/content/service-center_render- service-center. If you do not have internet access, please contact Horizon Product Support to obtain an RMA number along with instructions for submitting your product for service. When calling Horizon, you will be asked to provide your complete name, street address, email address, and phone number where you can be reached during business hours. When sending products into Horizon, please include your RMA number, a list of the included items, and a brief summary of the problem. A copy of your original sales receipt must be included for warranty consideration. Be sure your name, address, and RMA number are clearly written on the outside of the shipping carton.
NOTICE: Do not ship Li-Po batteries to Horizon. If you have any issues with a Li-Po battery, please contact the appropriate Horizon Product Support office.
Warranty Requirements
For Warranty consideration, you must include your original sales receipt verifying the proof-of-purchase date. Provided warranty conditions have been met, your Product will be serviced or replaced free of charge. Service or replacement decisions are at the sole discretion of Horizon.
Non-Warranty Service
Should your service not be covered by warranty, service will be completed and payment will be required without notifi cation or estimate of the expense unless the expense exceeds 50% of the retail purchase cost. By submitting the item for service you are agreeing to payment of the service without notifi cation. Service estimates are available upon request. You must include this request with your item submitted for service. Non-warranty service estimates will be billed a minimum of ½ hour of labor. In addition, you will be billed for return freight. Horizon accepts money orders and cashier’s checks, as well as Visa, MasterCard, American Express, and Discover cards. By submitting any item to Horizon for service, you are agreeing to Horizon’s Terms and Conditions found on our website http://www.horizonhobby.com/content/service- center_render-service-center.
ATTENTION: Horizon service is limited to Product compliant in the country of use and ownership. If received, a non-compliant Product will not be serviced. Further, the sender will be responsible for arranging the return shipment of the un-serviced Product, through a carrier of the sender’s choice and at the sender’s expense. Horizon will hold non-compliant Products for a period of 60 days from notifi cation, after which it will be discarded.

Warranty and Service Contact Information

Country of Purchase| Horizon Hobby| Contact Information| Address
---|---|---|---
United States of America| Horizon Service Center (Repairs and Repair Requests)| servicecenter.horizonhobby.com/ RequestForm/|

2904 Research Rd

Champaign, Illinois, 61822 USA

Horizon Product Support (Product Technical Assistance)| productsupport@horizonhobby.com

877-504-0233

Sales| websales@horizonhobby.com
800-338-4639
European Union| Horizon Technischer Service

Sales: Horizon Hobby GmbH

| service@horizonhobby.eu| Hanskampring 9

D 22885 Barsbüttel, Germany

+49 (0) 4121 2655 100

FCC Information

Contains FCC ID: BRWWACO1T
This device complies with part 15 of the FCC rules. Operations are subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
CAUTION: Changes or modifi cations not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
This product contains a radio transmitter with wireless technology which has been tested and found to be compliant with the applicable regulations governing a radio transmitter in the 2.400GHz to 2.4835GHz frequency range.
Supplier’s Declaration of Conformity Blade 120 S2 RTF/BNF (BLH1100 / BLH1180)
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

CAUTION: Changes or modifi cations not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.

NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
  Horizon Hobby, LLC
  2904 Research Rd.
  Champaign, IL 61822
  Email: compliance@horizonhobby.com
  Web: HorizonHobby.com

IC Information
Contains IC: 6157A-WACO1T
This device complies with Industry Canada license-exempt RSS standard(s). Operation is subject to the following two conditions:

(1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device.

Compliance Information for the European Union
EU Compliance Statement: **Blade 120 S2 RTF (BLH1100)**
Horizon Hobby, LLC  hereby declares that this product is in compliance with the essential requirements and other relevant provisions of the RED, EMC, and LVD Directives.
A copy of the EU Declaration of Conformity is available online at: http://www.horizonhobby.com/content/support-render-compliance.

Blade 120 S2 BNF (BLH1180)
Horizon Hobby, LLC  hereby declares that this product is in compliance with the essential requirements and other relevant provisions of the RED and EMC Directives.

Instructions for disposal of WEEE by users in the European Union
This product must not be disposed of with other waste. Instead, it is the user’s responsibility to dispose of their waste equipment by handing it over to a designated collections point for the recycling of waste electrical and electronic equipment. The separate collection and recycling of your waste equipment at the time of disposal will help to conserve natural resources and make sure that it is recycled in a manner that protects human health and the environment. For more information about where you can drop off your waste equipment for recycling, please contact your local city offi ce, your household waste disposal service, or where you purchased the product.

©2020 Horizon Hobby, LLC.
Blade, the Blade logo, E-Flite, BNF, the BNF logo, DSM, DSM2, DSMX, SAFE, the SAFE logo, Spektrum AirWare
and ModelMatch are trademarks or registered trademarks of Horizon Hobby, LLC.
The Spektrum trademark is used with the permission of Bachmann Industries, Inc.
All other trademarks, service marks, and logos are the property of their respective owners.
US 9,930,567. US 10,419,970. Other patents pending.
Created 3/20
61256
BLH1100, BLH1180

References

• RC Airplanes and Helicopters, RC Cars and Trucks, RC Boats, RC Radios | Horizon Hobby
• Spektrum RC Transmitters and RC Electronics | Spektrum

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>