Shenzhen Esorun Technology SLIM Ultra-Thin Wireless Car Mount User Manual
- June 6, 2024
- Shenzhen Esorun Technology
Table of Contents
Shenzhen Esorun Technology SLIM Ultra-Thin Wireless Car Mount
Ultra-thin Wireless Car Mount
OVERVIEW
How to Use
Step 1: Fix the air vent clamp or dashboard holder lo the device
Step 2: Use the Type•C cable packed in the box to connect the device and the car charger.
To achieve fast charging, QC2.0/3.0 car charger Is required.
Tips
Please match the phone’ s coil to “Wireless charging area” I check the page 2 by adjusting the bottom stand.
Pull down the foot rest to adjust the height Adjust the bottom stand for different smartphone. (Normally the wireless receiver coll is located in the phone’s center.)
Pull down to adjust the height of foot support
Tap Step3: to unlock the touch area and open the arm clip
Step 4: ‘ When a phone or other object is placed into the I To device, avoid
the any arm hurt, please automatically make closes sure your and fingers
closes. iI are not in the pathway of arms.
Step 5: To get the phone out of the Device, simply touch the touching I area
with your finger (see page1 ). I (NOTE: Short touch is a must and enough; Keep
your finger on i the touching area will not unlock the arms.)
There is a wireless charging aperture indicator on the front of the
body
- Aperture indicator State:
- Standby: Blue Breath
- Charging: The Blue Light is always on Full charge or abnormal charge: lights out
Power and wireless charging indicator light at lower left corner
- Power Supply and wireless charging indicator light status: Standby: Red Light is always on.
- Charging: The Blue Light is always on.
- Full charge: lights out.
- Foreign body detection: alternating red and blue ii ashes. Under-voltage, over.voltage, over-temperature protection:
- Red Light flashing
Fits Below Supports (Not Included) Ball Diameter: 16.8±0.3mm
Product Function Specification
-
1.lnput: 12V/1.67 A; 9V2A; 5V/2A
2.0utput: 9V/1 .67A; 9V/1.12A; 9V/0.83A; 5V/1 A 3.0peraling Temperalure:·10 to 60 “C
4.Ch0rging Power: 15W (Mex); 1 OW; 7 .5W (for IPhone X/8/8+) and 5W. -
5. Charging Efficiency: 60% to75%
6. Ch0rging Dist0nce: up to 6 mm -
7 .Over Temperoture Protection: When charging, if thetemperature goes over 60 “C, the device will automatically stop charging and the transmitter light will flash red(one second on/one second off). When the temperature drops to 40 “C, the device wilt automatically recharge. 8.0ver voltage protection: when the Device Is working at SW wireless charging, it will automatically stops as soon as the input voltage is over 6V; for 1 OW wireless, the Device stop charging when Input
is over 1 OV; For 15W wireless charging, the Device will stop when the Input voltage is over 13V.
9 .Support WPC Qi wireless charging protocol.
10. FOD function: red & blue lights hlink.
Product Function- Instruction
1.Automatic sensing of gravity, no need to manually switch
the 2.Built· in mobile wireless phone charging bracket. Easy transmitter to
operate module with for one mobile hand phone
for wireless charging
Precautions
- When charging, please select the QC2.0 or QC3.0 Adapter. Do not use any damaged chargers.
- Please do not charge the equipment that are incompatible with this product.
- Do not store the equipment in a cold place. Otherwise, if temperature rises to normal temperature. moisture will pent up inside It end damage the electric appliance.
- Do not attempt to open the equipment, unauthorized dis· assembly or modification will damage equipment or related wireless charging functions.
- Do not throw, tap or shake the equipment; rough handling of the equipment will damage the internal circuit board and the mechanical structure.
- Use the clean and moist soft cloth to clean the surface of the equipment. Do not use or store the equipment in dusty or dirty pieces.
- some components of this product are magnetic and metal materials may be adsorbed onto this product. Please do not use bank cards, creditcerds or any other items with magnetic near the product so as to avoid losing the data stored due to demagnetization.
- Please carefully handle your charger and accessories, the following recommendations will help you effectively use the warranty service.
- Please keep the equipment dry. Rain, moisture and various liquid may contain minerals that will corrode the circuit. If the equipment is wet, please dry the product es soon es possible or use e soft cloth to wipe it clean.
losing the date stored due to demagnetization.
Dashboard Holder
Dashboard Holder is with an extendable mechanic arm.which allows the phone can be pieced at the optimal charging position, achieving the maximum charging electronic current.
Tips
- When using this product. please make sure that the product is connected to the power. To achieve fast charging, QC2.0/3.0 car charger is required.
- If the clamping arm of this product cannot be opened, pull the left and right arms by hand to take out the phone.
FCC Warning
This device complies with part 15 of the FCC Rules. Operation is subject to
the following two conditions:(1) This device may not cause harmful
interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation. Any Changes or
modifications not expressly approved by the party responsible for compliance
could void the user’s authority to operate the equipment.
This equipment has been tested and found to comply with the limits for a Class
B digital device, pursuant to part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates uses and can radiate radio
frequency energy and, if not installed and used in accordance with the
instructions , may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful interference to
radio or television reception, which can be determined by turning the
equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
The equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. During the operation of device a distance of 15 cm surrounding the device and 20 cm above the top surface of the device must be respected.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>