MILESCRAFT 1213 Hingemate300 For Mortising Of Interior Doors Black User Manual

: October 27, 2023
: MILESCRAFT

Table of Contents

1213 Hingemate300 For Mortising Of Interior Doors Black
EASY MEASURE GUIDE
Documents / Resources

For Mortising Of Interior Doors Black
User Manual
Model: 1213

1213 Hingemate300 For Mortising Of Interior Doors Black

HingeMate300™

1 – Steel Template Frame
2 – 1/2˝ Router Bit w/Bearing
3 – 3.5˝ Hinge Template
4 – 2.5˝ Hinge Template
5 – 3˝ Hinge Template| 6 – 4˝ Hinge Template
7 – 4.5˝ Hinge Template
8 – Latch Plate Template
9 – Strike Plate & Latch Plate Template
10 – T-Strike Plate Template
11 – Mounting Screws (2)
---|---

MILESCRAFT 1213 Hingemate300 For Mortising Of Interior Doors Black -
1 PACKAGE CONTENTS

Unpack all items and check with Figure 1 and the “Replacement Parts table” (see page 9). Make sure all items are accounted for before discarding any of the packing material. For any missing parts, contact Customer Service at info@milescraft.com or
1-224-227-6930 in U.S. and Canada.
Outside of the U.S. and Canada dial 001-224-227-6930.
SAFETY WARNING:
Read, understand, and follow your power tool manufacturer’s instructions for safety. Always wear safety glasses or eye shields before commencing power tool operation. Always keep hands, face, hair, loose clothing, and body at a safe distance from spindles and cutting tools. Always keep a firm grip on tool handles when in operation. Always disconnect from the power source before adjusting power tools.
STANDARD PLACEMENT OF DOOR HARDWARE

MILESCRAFT 1213 Hingemate300 For Mortising Of Interior Doors Black -
3 |
---|---

EASY MEASURE GUIDE

Measure from the TOP of the door or jamb to the tab at the CENTER of the template.
ALL MEASUREMENTS ARE IN INCHES

MILESCRAFT 1213 Hingemate300 For Mortising Of Interior Doors Black -
2

HINTS

If the door jamb has an existing stop or if the stop on the door jamb exceeds the height of the template frame, you will want to create a shim or spacer to accommodate the additional height that you will need (see img. 1). Please be sure that the router bit will still properly ride along the inside of the hinge template after your spacer is in place. 2 It may be necessary to remove the thickness selector assembly from each end of the metal frame to permit a deeper location of the frame (see img.
This will eliminate the automatic parallel alignment capability of the metal plate, so you must measure carefully to be sure the distances to the holes are correct before attaching the plate to the door or jamb. Be sure to re-install the thickness selector cam assemblies to the metal plate when the job is complete, so the parts do not get lost.

MILESCRAFT 1213 Hingemate300 For Mortising Of Interior Doors Black -
5

HOW TO USE THE HINGEMATE300™

Select the thickness of your door using the thickness selector knobs on the steel template frame (see img. 1).
A- Select for hinges, strike plates and latch plates on 1-3/8˝ doors.
B- Select for hinges on 1-3/4˝ doors.
C- Select for strike plates and latch plates on 1-3/4˝ doors.
Position steel template frame on edge of door or jamb (see img. 2).
Slide the steel template frame back on the door or jamb until the thickness selector cam rests against the door or jamb (see img. 3).
HOW TO USE THE HINGEMATE300™
Insert template into steel template frame for the appropriate hinge.
Be sure the appropriate style for your hinge (square* or rounded), strike, or latch plate is over the mortise you will route. Rotate the template to achieve different radii; a corner chisel can be used to create a 90° angle. (See in.

Measure from the top of the door or jamb to the centered tape measure tab of the template. Measure to the appropriate dimension found in the “Easy Measure Guide” on page 4 of this manual. (See image. 5)
HINT: When using square-corner templates, chiseling will be required.
HOW TO USE THE HINGEMATE300™
Fasten the steel template frame to the door or jamb (see img. 6).
Install the included router bit into your router and adjust the cutting depth to the thickness of the door hardware being installed. Be sure the power to your router is off.
Rout out all material inside of the template. Use the bearing on the included router bit to roll along the inside edges of the template (see image. 7).
If installing square-cornered door hardware, chisel corners (see img. 8). bk Repeat Steps 2–9 for the rest of the door hardware being installed. hardware being installed.

MILESCRAFT 1213 Hingemate300 For Mortising Of Interior Doors Black -
8

Replacement parts
Model: 1213

MILESCRAFT 1213 Hingemate300 For Mortising Of Interior Doors Black -
9

| Part #| Description| Qty
---|---|---|---
1| 63| Socket Set Screw| 2
2| 71| Mounting Screws| 2
3| 10015| Spring| 2
4| 21018| Steel Template Frame| 1
5| 30275| 3.5 – Hinge Template| 1
6| 30276| 2.5 – Hinge Template| 1
7| 30277| 3 – Hinge Template| 1
8| 30278| 4 – Hinge Template| 1
9| 30279| 4.5 – Hinge Template| 1
10| 30280| 1 – x 2.25 – & 1.125 – x 2.25 – Latch Plate Template| 1
11| 30281| 2.25 Strike Plate & 1.125- x 2.7- Latch Plate Template| 1
12| 30282| 1.125 – x 2.75- Strike Plate Template| 1
13| 30283| Adjust Knob| 1
14| 30284| Adjust Knob Cam| 1
15| 70059| 1/2- Router Bit w/Bearing| 1

© 2021 Milescraft, Inc.
U.S. Patent #7,766,059 / 7,896,042
**www.milescraft.com

**

Documents / Resources

| MILESCRAFT 1213 Hingemate300 For Mortising Of Interior Doors Black [pdf] User Manual
1213 Hingemate300 For Mortising Of Interior Doors Black, 1213, Hingemate300, For Mortising Of Interior Doors Black, Interior Doors Black, Doors Black
---|---