PAX IM300 Encrypting Pin Pad Instruction Manual

IM300 Encrypting Pin Pad
Instruction Manual

PAX TECHNOLOGY LIMITED

PAX TECHNOLOGY LIMITED reserves the right to change product specifications without prior notification.

Product Description

1. Mounting Points
2. Tamperproof Switches
3. Protective Lens & LCD Screen
4. Stainless Steel Keys

Installation

1. SAM& SIM Cards
   Unscrew the SAM card cover to remove it. Open the mount and insert the card into the slot with the contacts facing downwards and the clipped corner of the card to the upper right, then lock the mount with the card inside and replace the cover.

2.  Recommended Device Connection
   The IM300 can be connected to a magnetic- strip/IC card reader(IM500 of PAX is recommended) as well as a contactless card reader (IM700 of PAX is recommended) through the use of RS232 serial ports using an RJ45 cable as indicated in Figure 5 and Figure 6. The IM300 both controls and powers the magnetic-strip/IC card and contactless card reader. If the IM300 is used to link to devices aside from the IM500 and IM700, the user must first confirm that the software and hardware for the connection is suitable.

3. This product needs to be installed in a professional way:
   a) Antenna installation for WIFI/BT:
   NO.8 SMA connector is for the WIFI/BT antenna connection.
   The user must follow the antenna parameter if they won’t install the WIFI/BT antenna to IM300 :
   Frequency：2.400 GHz ~ 2.497 GHz
   Gain：2.400 GHz ~ 2.497 GHz 0dBi
   Antenna radiation efficiency：2.400 GHz ~ 2.497 GHz >50%
   Polarity： vertical
   VSWR: 2.400 GHz ~ 2.497 GHz <2.0
   Directivity：2.400 GHz ~ 2.497 GHz <5
   Connector： SMA (Male & gold plated)
   If the above parameters are satisfied, the user can use the antenna that satisfies the condition with the IM300.
   Note: WIFI/BT antenna information used for the test collocation is as follows:
   Brand name: GUOXU;
   Model name: GX086S;
   Antenna type: Monopole
   Antenna Gain: 0 dBi
   b) Special used for industrial and commercial purposes:
   It should be sold to the dealers authorized by PAX and installed by a professional person;
   It should be used in the unattended machine and cannot be available to the average consumer because of its security and applicability;
   This device has got the PCI 5. X certification and is provided with an Anti- Remove function which means the necessity of professional installation.
   c) Other professional installation requirements:
   NO.8 SMA connector is designed for the WIFI/BT antenna connection. The user can connect the antenna to IM300 via the port. The antenna should be installed as high as possible on the unattended machine.
   Installation requires the special training that PAX can provide including programming, access to the keypad, field strength measurements made, and so on.

Instructions

1. Switching the IM300 on and off
   Switch on: Connect the IM300 to an appropriate power terminal either via the power cable or the MDB cable (make sure to have the appropriate voltages and pinouts).
   Switch off: Disconnect the IM300from whatever power terminal it is connected to.

2. Using the Keypad
   The IM300 contains a standard numeric keypad; 1 through 9 incrementing through three rows, with 0 being in the bottom center fourth row (center-left in Figure 7 because of the function keys in the last column). The functional keys from top to bottom are: cancel, clear, helpful, and enter. The two up and down navigational keys are respectively on the bottom center-right and the bottom far-left. Specific actions performed by the keys are context-specific and should be intuitive given whatever is shown on the screen.

Specifications

4Gb NAND Flash
Display:| 2.8″ TFT color display
320 x 240 pixels
SAM Slots:| 2 slots, ISO/IEC 7816
Peripheral Ports:| 4 RS232 (RJ45)
1 Ethernet (RJ45, 100Mb/s)
2 USB 2.0 (USB Type-B)
1USB 2.0 (USB Mini-B)
1 MDB port
1 microphone jack
1 earphone jack
1 1.25mm 5 pin socket
WIFI:| 2.4GHz 802.11 b/g/n
Bluetooth:| Bluetooth V4.0
Battery:| 1 Nickel button battery, 600mAh, 3.0V
Power Supply:| Input: 9VDC~42VDC (MDB)
Output: 5VDC (USB2.0 Type-A) x 2
12VDC (RS232 via RJ45) x 2
Buzzer:| ≥80dB
Operating Temperature:| -20°C~70°C
-4°F ~158°F
Storage Temperature:| -30°C~70°C
-22°F ~158°F
Relative Humidity:| 5%~95% (without condensation)
Dimensions:| 92mm x 33.8mm x 140mm

(The device can work properly below 70 °C, the metal surface of the device may increase the risk of burn injuries when the ambient operating temperature exceeds 55°C.)

Maintenance and Usage

1. Do not damage any of the cables; if a cable becomes damaged, immediately discontinue its use and seek a replacement.
2. Make sure the terminals the power or MDB cables connect to provide the appropriate voltages at the proper pins.
3. Do not insert unknown materials into any port on the IM300, this may cause serious damage to the device.
4. If the IM300 becomes defective, please contact a professional technician for repairs instead of attempting them on your own.
5. The IM300 contains hardware tamper-proofing measures; disassembly of the device will trigger the tamper circuits, at which point it will have to be rearmed by qualified personnel before the device is ready to resume operation.
6. When mounting the IM300 into its enclosure, ensure that the tamperproof switches are fully depressed against the mounting panel.
7. The IM300 is designed for outdoor use; however, during normal use, its surface should still be kept clear of dirt and possible liquid contaminants.
8. While the IM300 is designed to resist the ingress of dust and liquids from the front face, it is not designed to resist pressurized liquids such as water hoses. Keep the back of the device away from dust and liquids as much as possible.

FCC Compliance Statement

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:

1. This device may not cause harmful interference, and
2. This device must accept any interference received, including interference that may cause undesired operation.

FCC WARNING

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

FCC CAUTION
Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate this equipment.

RF Exposure Information

This device complies with FCC radiation exposure limits set forth for an uncontrolled environment. In order to avoid the possibility of exceeding the FCC radio frequency exposure limits, human proximity to the antenna shall not be less than 20cm (8 inches) during normal operation.

ISED Notice
This device complies with Innovation, Science and Economic Development Canada license-exempt RSS standard(s). Operation is subject to the following two conditions:

1. this device may not cause interference, and
2. this device must accept any interference, including interference that may cause undesired operation of the device.

IC: 11689A-IM300BW1
CAN ICES-3 (B)/NMB-3(B)
This Class B digital apparatus complies with Canadian ICES-003.
ISED RF Exposure Statement
This device complies with ISED RSS-102 RF exposure limits set forth for an uncontrolled environment. In order to avoid the possibility of exceeding the IC RSS-102 RF exposure limits, human proximity to the antenna shall not be less than 20cm (8 inches) during normal operation.
PAX TECHNOLOGY LIMITED reserves the right to change the product’s technical specifications without notifying.

PAX TECHNOLOGY LIMITED
Manufacturer: PAX Computer Technology (Shenzhen) Co., Ltd.
Address:4/F, No.3 Building, Software Park, Second Central Science-Tech Road, High
Tech Industrial Park, Shenzhen, Guangdong, P.R.C.
Tel: 0755-86169630 Fax: 0755-86169634
Website: http://www.pax.com.cn
Responsible Party:
PAX Technology, Inc.
8880 Freedom Crossing Trail, Building 400, 3rd Floor Suite 300, Jacksonville, Florida,
USA 32256
Help-desk
1 877-859-0099

PAX TECHNOLOGY LIMITED
Room 2416, 24F., Sun Hung Kai Centre, 30
Harbour Road, Wanchai, Hong Kong
Tel: +852-2588-8808
Fax: +852-2802-3300
Website: www.pax.com.hk 

References

• PAX Technology | Global Website | Payment Terminals

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>