ALOGIC WC-087 3-in-1 Wireless Charging Dock User Guide

ALOGIC WC-087 3-in-1 Wireless Charging Dock

OVERVIEW

1. Qi Charging Surface
2. DC Jack
3. LED indicator
4. USB-A Charging Port

Use this port to charge wired devices

1. Insert the power plug which suits the power outlets in your country into the included power adapter and twist to lock in place.
2. Connect the power adapter cable into the wireless charging dock and then plug the adapter into a power outlet. Two white LED lights will appear on the front of the device to indicate that the device is on and ready for use.

Package Contents

1. Ultra Power 3-in-1 Wireless Charging Dock
2. Power Adapter
3. AU/EU/UK/US Plugs
4. User Manual

Operating Instructions

Charging Wireless Devices

1. Place your device(s) with wireless charging on top of the wireless charging pad. There are two charging regions (left and right sides of the charging pad) that allow two devices to be charged simultaneously.
2. The LED Lights will appear to “breathe” slowly to indicate that a successful connection has been established and wireless charging has commenced.
3. In the event that a metallic object is detected or if your device is emitting high temperatures the LED indicator will flash red.

Charging Wired Devices

1. To charge a device via the USB-A port, connect the USB-A end of your existing charging cable to the charging dock’s USB-A port and the other end to your device. Charging should commence immediately.

Understanding the LED lights and their meanings

Troubleshooting

Warnings

1. This device uses inductive charging. Do not place metallic objects (aside from devices which support wireless charging) on top of the charging pad.
2. The device supports detection of large metallic objects such as keys. In the event that large metallic objects are detected the wireless charging indicator(s) on the device will show a red light and the device will not commence charging.
3. Avoid placing phone cases which include metallic portions on the charger. In rare cases it may not be possible to detect smaller metallic objects, such as foil logos on phone cases, and the charger may continue to operate. In these cases, the metallic object will heat up and may cause damage to the device being charged over time.
4. This device is designed for indoor use only.
5. Do not deliberately damage the device or expose it to damp, direct sunlight, or high temperature conditions.
6. It is normal for the device to be slightly warm to touch during operation. Provide adequate ventilation and do not cover the device while in operation.
7. Disassembling or failing to properly use and care for your device will void the warranty on the product.
8. Do not use the product if it becomes damaged as this could pose a risk of causing damage to connected devices.
9. ALOGIC bears no responsibility for damage to the a device or incidental damages arising from improper use or lack of care.
10. ALOGIC will not be held liable for repair or replacement of the device or other damages in these circumstances.

FCC Compliance Statement

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (0) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to Operate the equipment. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCc Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. is equipment generates, uses, and can radiate radio Frequency ener9y and, ir not installed and used in accordance with tne instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not OCCur in a particular installation. I this equipment does cause harmful interference to radio or television reception, which can be determined by turning thee equipment of and on, the user is encouraged to try to correct the interference by one or more of the following measures:

Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
Consult the dealer or an experienced radio/TV technician for help.

Responsible Party – U.S. Contact information ALOGIC USA LLC3730 Parish Ave Fremont CA 94536 USA

EU Declaration of Conformity

Hereby, ALOGIC Corporation declares that this product is in compliance with Directive 2014/53/EU. The full text of the EU declaration of conformity is available at the following internet address by clicking on the Compliance Documentation link at: www.alogic.co

FCC Warning

This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, includinginterference that may cause undesired operation. Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
• This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment.
• This equipment should be installed and operated with a minimum distance of 20 cm between the radiator and your body

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>