Drones MW412 I/R Mini Copter/Drone for Age 8+ Instruction Manual

MW412 I/R Mini Copter/Drone for Age 8+

Instruction Manual

• Headless mode
• One key flip
• One key rotation
• One key Headless mode return

Please read this instruction carefully before using.

1. INCLUDED PARTS

2. TRANSMITTER

2.1 Introduction Transmitter

2. 2 Install Batteries

3. Battery cover

First, connect USB to the USB slot on the Computer or to USB charger. At this moment the indicate light will be constantly on at USB charging outlet. Then connect the battery to USB charging line. The red light will be off which indicates it is in charging and a constant light indicates that it has been fully charged. The time for charging is about 30 to 40 minutes and fight time is about 6 minutes. For safety reasons, charging should be done in sight

4. OPERATION INSTRUCTIONS

4.1 Power on & Match
4.1.1
Connect the battery line to the fuselage power supply, keep it in a horizontal position. Then turn on the transmitter. the bottom two LED lights flash quickly. Push the throttle lever to the highest position. then pull it back to the lowest position, there will be one clear sound from the transmitter, it shows the binding finished. Push the left joystick accelerator can launch vehicle.

4.1.2. After code match is done with the air vehicle, push the left joystick throttle to start the air vehicle.

4.2 Gyroscope collaboration
When code match is finished, put the air vehicle on a level position and push the throttle stick and the direction stick 45 degrees toward the right bottom to collaborate the gyroscope. If two LED lights flick on the air vehicle, it means the gyroscope is returning and scanning for position. If the LED light stops, it suggests the collaboration is successfully done.(Refer to the picture on the right)

Note: Before flying, the quadcopter should be placed on the flat surface to collaborate to ensure stable flying.

If the quadcopter flies off tract, you can adjust it with the remote.

5. OPERATING AND CONTROL

5.1 Operation
It may take some time to learn how to operate this quadcopter. Please take your time to learn in the beginning. If the quadcopter slightly descends, softly push the left rod to adjust the flying height.

DO NOT PUSH THE ROD TOO SHARPLY.

5.2 Trimming

ADJUSTMENT OF EACH TRIM
Slowly push upward the throttle lever. When the aircraft is flying off the ground, if the aircraft keep inclining to different direction, please use the trimmer key to trim it to fly in narmal state.

1. Adjustment of elevator trim
Just before the aircraft lift-off, the nose lean forward/backward, When leans forward, adjust the trim to down. When leans backward, adjust the trim up.

2. Adjustment of aileron trim

When the aircraft is just taking off, the aircraft may make left/right side- flying, When making right-side flying, please trim it to the left. When making left-side flying, please trim it to the right.

6. 360° FLIPS

Press down the right rod and the transmitter will beep one time to enter advanced mode. Now flip is allowed. In order to get good flipping performance. It is recommended to keep 1.5 meters of altitude between the quadcopter and the ground. It will make flipping easier darning ascending as altitude will be lost during flips.

Note: keep the aircraft at a height of 2-3 meters when it is rolling, so that it is easier to maintain altitude when the aircraft is tumbling.

7. HEADLESS MODE

7.1 Headless Mode Shift

• Starting Headless Mode: After pairing the quadcopter, press down on the left rod to enter Headless Mode. This can be down when the quadcopter is in the air or on the ground. The transmitter will beep and the fusional two indication the quadcopter will flash. Green light for the forward direction.
• Leaving Headless Mode: Press down on the left rod to exit Headless Mode. The controller will beep and all four indicators on the quadcopter will turn on.

See the diagram. Note in Headless Mode. A forward push on the controller will send the quadcopter in a forward direction, away from you. Pull back and the quadcopter will come towards you again, no matter the orientation of the front black blades of the quadcopter to the user as long as he is stationary. If the user changes location, simply re-pair the controller using below instructions.

7.2 Direction Calibration
Press the button of one key return,, the quadcopter will return automatically. You can push the right lever up to correct the channel if deviation. (in the front of the frequency after reboot to normal return).Press the button of one key return again(the transmitter “Di”),the quadcopter ends return. Or push the right lever up to end return.

8. FLIGHT ENVIRONMENT

Under the bad condition above, the quadcopter shall not operate to avoid any potential damages.

9. INSTALL BLADES

The blades shalled to designated location. Blade NB shall be installed to location NB on body. LED

10. TROUBLE SHOOTING

10.1 Transmitter and quadcopter not bland Solution:

1. To ensure that the frequency of success. re frequency .
2. Battery power shortage, replace the battery.
3. To confirm that the remote control is not the original match.

10.2 Unable to flip
Solution:

1. Press Function combination button, change to flip mode.
2. Check if Li-Po power is too low and needs to be recharged.

Install blades: Hold the head to aim at the motor axis and press down to lock. Be careful not to damage or deform the blades.

10.3 Quadcopter is shaking with noise:
Solution:

1. Check blade if deformation or not, replacement new blade.
2. Off the quadcopter power and restart.
3. Put the quadcopter in the horizontal place, and recalibrate the gyroscope.

10.4 Cannot take off
Solution:

1. Wrong installation of the blade. Make sure the blade placed on the right motor.
2. Check quadcopter canopy if loose or not, block blades flying.
3. Check quadcopter battery is power full, if the low power, quadcopter canopy inner light will be alternately flashing.

FCC statement

This device complies with Part 15 of the FCC rules. Operation is subject to the following two conditions: 1) this device may not cause harmful interference, and 2) this device must accept any interference received, including interference that may cause undesired operation.

Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.

However, there is no guarantee that interference will not occur in particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.

FCC Radiation Exposure Statement
This device complies with FCC RF radiation exposure limits set forth for an uncontrolled environment. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>