FPV Drones 3W 5.8GHz Powerful Analogue VTX with Heat Dissipation Instruction Manual
- June 1, 2024
- FPV Drones
Table of Contents
FPV Drones 3W 5.8GHz Powerful Analogue VTX with Heat Dissipation
Dimension
Product Information
- 5.8G 48 Channel: (A.B.E.F.R.L; 5362MHz-5945MHz).
- Maximum power: 3W (25mW/1000mW/2000mW/3000mW, adjustable); • Input Voltage Input voltage: DC 7V-36V, support 2-8S battery input Support 28Sbatteryinput.
- Antenna interface: MMCX.
- Communication protocol: IRC Tramp.
- Heat dissipation mode: aluminium alloy heat sink + fan aluminium alloy heat sink + fan.
- Mounting hole position: 30.5mm*30.5mm /ø3.15mm8.
- Product dimension: 37.7mm36.1mm11mm.
- Product weight: 16g.
Interface and key indicator layout
- Frequency indicator: red LED Frequency indicator: red LED
- Frequency band indicator: blue LED Frequency band indicator: blue LED
- Power indicator: green LED Power indicator: green LED
- Frequency band, frequency adjustment button Frequency band, frequency adjustment button
- Power adjustment button Power adjustment button
- 1.0 6P cable base 6.1.0 6P cable base
- MMCX antenna bas MMCX antenna base
Key control and LED indicator definition Key control and LED indicator definition
- Button ④ is the frequency point and frequency band switching key; each time button ④ is pressed briefly, the red LED corresponding to the next frequency point will flash, followed by frequency point 1.2. 3.4.5.6.7.8.
- This operation can be looped; see the picture below for details! Button④ is the frequency point and frequency band switching key; each short press of button ④ switches to the next frequency point and the corresponding red LED will flash, which is frequency point 1.2.3.4.5.6.7.8. This operation can be looped; see the picture below for details!
Press the button ④ to switch frequency points
Red LED| CH1| CH2| CH3| CH4| CH5| CH6| CH7| CH8
Flashes 1 time| Flashes 2 times| Flashes 3 times| Flashes 4 times| Flashes 5
times| Flashes 6 times| Flashes 7 times| Flashes 8 times
- Long press button ④ to switch frequency bands. Press and hold for 5 seconds and the corresponding blue LED will flash, followed by frequency group A.B.E.F.R.L.
- This operation can be looped; see the picture below for details!
- Press and hold the button ④to switch frequency bands. Press and hold for 5 seconds and the corresponding blue LED will flash, followed by frequency group A.B.E.F.R.
Hold down the button ④ for 5 seconds to switch the frequency band
Blue LED
- BAND A Flashes 1 time
- BAND B Flashes 2 times
- BAND E Flashes 3 times
- BAND F Flashes 4 times
- BAND R Flashes 5 times
- BAND L Flashes 6 times
- Button ⑤ is a power adjustment button.
- Each short press switches the power to one gear, cycling between the four gears of 25mW, 1000mW, 2000mW, and 3000mW.
- The green LED is the power indicator.
- The status is as shown in the figure below. 25mW flashes once, 1000mW flashes 2 times, 2000mW flashes 3 times, and 3000mW flashes 4 times.
- Press and hold for 3 seconds to enter pit mode, the green light will stay on.
- See the picture below for details! Button ⑤ is the power adjustment button.
- Each short press switches the power to one gear and cycles between the four gears of 25mW, 1000mW, 2000mWand 3000mW.
Pit Mode
- Short press button ⑤ to switch power;
- Long press to enter Pit mode
LED Green LED| Pit mode| 25mW| 1000mW| 2000mW| 3000mW
Long bright| Flashes 1 time| Flashes 2 times| Flashes 3 times| Flashes 4 times
Channel mapping parameter table
VTX Wire description
Wiring Table:
Safety Precaution Note
- When installing the JARIBEL 3W VTX please leave space around the VTX to help air circulation. In the case of the VTX overheating, the unit’s overheating protection will activate, reducing power transmission, or even turning off power transmission.
- It is recommended to ensure the correct voltage range and correct positive and negative polarity before turning on the power to avoid burning out the components.
- An antenna must be connected before powering on the unit.
- Powering the unit without an antenna will cause the VTX to burn out.
- Please read the instruction manual before using this product.
Packing List
- 3W 5.8Ghz FPV Analogue video transmitter (VTX)
- MMCX to RPSMA antenna pigtail (120mm)
- Connector cable. (95mm)
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>