LOREX W482CAD Series 2K Wi-Fi Smart Deterrence Camera User Guide

LOREX W482CAD Series 2K Wi-Fi Smart Deterrence Camera

Package contents

Note: The following contents is based on 1 camera
Dimensions
Camera with Wall Mount

• Height: 3.1” (78mm)
• Width: 3.1” (78mm)
• Length: 5.0” (128mm)

Camera with Ceiling Mount

• Height: 4.2” (107mm)
• Width: 3.1” (78mm)
• Length: 5.2” (132mm)

Overview

1.  Microphone
2. Warning light
3. Status indicator
4. 9.2ft (2.8m) USB power cord
5. Threaded insert (for mounting)
6. Speaker
7. MicroSD slot (card included)
8. Pairing / reset button
9. QR code

Status indicator

Camera setup

1. Connect power to the camera with the provided power adapter. When you hear the chime and the status indicator is flashing green, the device is ready for setup. Optional: Connect the weatherproof extension cable to the camera’s cable.
2. Download the Lorex Home app by scanning the QR code.
3. Open the Lorex Home app, and sign in or create an account.
4. Tap + in the app, then follow the in-app instructions to complete the device setup.

Ensure you update to the latest app and camera firmware version.

App Live View

Camera Placement

• Place the camera close to your Wi-Fi router as possible.
• Reduce the number of obstructive materials between the camera and the router or access point. Concrete, brick, metal and wood are the most common materials in your house that can cause poor signal strength.
• Other electronic devices such as microwaves, TVs, cordless phones, and baby monitors can cause signal interference. It is recommended to install the camera as far away from these devices as possible.

Optimize Motion Detection

Distance Optimal accuracy for objects within 5ft to 50ft (1.5~15m).
Angle Angle the camera around 30°-60° down from the level position.
Height Install the camera between 8-16ft (2.5~5m) off of the ground.

Note: Accuracy of person detection will be influenced by multiple factors, such as the person’s distance from the camera, the height of the person, and the height and angle of the camera. Night vision will also impact the accuracy and distance of detection.

Wall Mounting

To wall mount the camera:

1. Place the mounting template onto the desired location.
   Note: Ensure an outlet is nearby, and keep in mind the cable lengths.

2.  Using a 15/64″ (6mm) drill bit, drill 2 holes over the triangle symbols on the template. Optional: Drill 15/64” (6mm) holes for the anchors.

3. Align the arrows of the mounting plate and template. Using a screwdriver and the provided screws, secure the mounting plate to the surface.

4. Align the arrows between the wall mounting bracket and plate. Push the bracket in to install, then slide down to lock in place. You will hear a ‘click’ when the bracket is installed.

5.  Attach the camera to the mounting bracket using the threaded insert at the rear of the camera. Rotate the camera clockwise until attached, then tighten into place with the adjustable nut.

6.  Adjust the camera to the desired angle.

Note: If the camera is not holding in place or is difficult to adjust, unplug the camera and slide the bracket up to detach from the mounting plate. Tighten or loosen the 3 screws at the back of the mounting bracket to adjust accordingly. Repeat steps 4-6 to re-install.

Ceiling Mounting

To ceiling mount the camera:

1. Place the mounting template onto the desired location.
   Note: Ensure an outlet is nearby, and keep in mind the cable lengths.

2. Using a 15/64″ (6mm) drill bit, drill 4 holes over the X symbols on the template. Optional: Drill 15/64” (6mm) holes for the anchors.

3. Remove the 4 pre-inserted plugs from the ceiling/table mounting bracket.

4.  Attach the camera to the ceiling/table mounting bracket using the threaded insert at the rear of the camera. Rotate the camera clockwise until attached, then use the wrench to tighten the adjustable nut in place.

5. Place the bracket over the drilled holes. Using a screwdriver and the provided screws, secure the bracket to the surface.

6. Rotate the adjustable ring counter-clockwise to loosen and adjust the camera to the desired position, then tighten to secure.

Optional:

• Feed the camera cable through the hole at the base of the bracket or the mounting surface.
• Open the camera’s settings in the app and enable Image Rotation to flip the camera image.

Please take attention that changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:

1. This device may not cause harmful interference, and
2. This device must accept any interference received, including interference that may cause undesired operation.

This device complies with Industry Canada licence-exempt RSS standard(s). Operation is subject to the following two conditions:

1. this device may not cause interference, and
2. this device must accept any interference, including interference that may cause undesired operation of the device.

This equipment complies with FCC/IC RSS-102 radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator & your body. The user manual for local area network devices shall contain instructions related to the restrictions mentioned in the above sections, namely that:)

1. the maximum antenna gain permitted for devices in the bands 5250-5350 MHz and 5470-5 MHz shall comply with the e.i.r.p. limit; and
2. the maximum antenna gain permitted for devices in the band 5725-5825 MHz shall comply the e.i.r.p. limits specified for point-to-point and non point-to-point operation as appropriate.

Need help?
Visit help.lorex.com for up-to-date information and resources:

• Download product guides
• Watch how-to-videos

Find related troubleshooting tips & FAQs W482CAD_QSG_TRILINGUAL_R1
Register your product
Please see our full Terms of Service and Limited Hardware Warranty Policy visit, lorex.com/warranty.This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesired operation.
Copyright © 2021 Lorex Corporation As our products are subject to continuous improvement, Lorex reserves the right to modify product design, specifications and prices, without notice and without incurring any obligation. E&OE. All rights reserved.

References

• Lorex Technical Support | LOREX Support
• Security Cameras - Home Security Camera Systems | Lorex

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>