Gude DHH Series Wood Splitter Instruction Manual
- June 3, 2024
- Gude
Table of Contents
DHH Series Wood Splitter
Instruction Manual
DHH 1250/12 T # 01962
DHH 1050/8 TC # 01963
Basic 10T/DTS # 02040
DHH 1050/10 TP # 02004
Please read the instructions carefully before starting the machine.
DELIVERED ITEMS
Assembly
Technical Data
WARNING The vibration emission level will vary because of the ways in
which a power tool can be used and may increase above the level given in this
information sheet.
The vibration emission level may be used to compare one tool with another.
It may be used for a preliminary assessment of exposure.
An accurate estimate of the vibratory load should also take into account the
times when the tool is shut down or when it is running but not actually in
use. This may significantly reduce the vibratory load over the total working
period.
Identify additional safety measures to protect the operator from the effects
of vibration such as: maintaining the tool and the accessories, keeping the
hands warm, and organization of work patterns.
Read and understand the operating instructions before using the appliance.
Abide by all the safety measures stated in the service manual. Act responsibly
toward third parties.
In case of any doubts about connection and operation refer please to our
customer center
Specified Conditions Of Use
The wood splitter has only been designed to split wood in the fiber direction.
Respecting technical data and safety precautions.
When splitting, it is essential to make sure the split wood only contacts the
checkered sheet of the bottom plate or the checkered sheet of the splitting
desk.
It is essential to follow instructions for installation, operation, repairs,
etc. to prevent hazards and damage.
Please do not forget that this machine, as designed, is not intended for
industrial use.
| Make sure there are no persons in the working area during operation or make
sure such persons keep a sufficient safety distance.
---|---
| The wood splitter has been designed to be operated by 1 person. The machine
must never be operated by two or more persons.
Wood splitter being operated by two persons, with one holding a piece of wood
and the other controlling the clamps is strictly prohibited.
Do not use this product in any other way than stated for normal use. Not
observing general regulations in force and instructions from this manual does
not make the manufacturer liable for damages.
Safety Instructions
Electrical connection
WARNING! Electric shock! There is a risk of an injury caused by electric
shock!
Operation is only allowed with a safety switch against stray current (RCD max.
stray current of 30mA).
Check the voltage. Technical data given on the type label must correspond with
the electric network voltage.
Insert the plug of the electrical cable in a socket of suitable shape,
voltage, and frequency complying with current regulations. Only for 400-volt
machines: It is essential to respect the engine rotation direction (see the
arrow on the engine) as an operation in the wrong direction would damage the
oil pump.
Warranty claims cannot apply in such a case. Change the rotation direction by
turning the connector polarity if necessary. Pursuant to the provisions of
„CE“ professional associations, etc., all splitters are fitted with an
Undervoltage release in the switch. This will prevent accidental repeated
starting in case of current interruption due to power failure, accidental
unplugging, defective fuse, etc. The machine must necessarily be turned on
again by repeated pressing of the green switch.
Wilful holding or blocking of the switch, unless neutral, will automatically
lead to switching failure. The warranty will not apply in such a case that
must naturally be checked.
- The machine meets the EN 61000-3-11 requirements and is subject to special connection conditions. That means that a user of optional points of connection is not allowed.
- The machine may cause temporary voltage fluctuation in adverse conditions.
- The machine has only been designed to be used on points of connection not exceeding the maximum allowable network impedance Zmax = 0.233 Ω.
- As a user, you must make sure, after consultation with your energy provider, if necessary, that your point of connection on which the machine is to be operated meets the requirements above.
Working area
For safe wood splitting, it is essential that the working area is flat and
slip-resistant and that sufficient space for moving is provided. To take the
wood splitter to your home, it is necessary there are no obstacles in the way,
i.e. no risk of tripping. Adequate lighting of the working area needs to be
provided.
Work preparation
Before putting the machine into operation, the working of the safety guards
(two-lever operation system, in particular) must be checked.
- Put both control levers down and the splitter knife down, app. 5 cm above the desk.
- One control lever to be released at all times, with the splitter knife remaining in the selected position. CAUTION! Whenever the machine is to be put into operation, make sure the splitter desk is firmly and safely fitted to the machine.
Operation
The power supply must be interrupted by pressing the red button on the switch
and unplugging the machine for any repair or servicing work or when leaving
the wood splitter. Turning to the Off position is not enough to interrupt the
power supply.
Using the wood splitter may lead to some hazards. Therefore, the machine may
only be handled by instructed and experienced persons. The operator must wear
close-fitting clothing and safety shoes.
Residual risks
Dry and dried-up wood may jump up when being split and injure the face of the
operator.
Adequate protective clothes to be worn!
Wooden pieces produced during splitting may fall down and injure the legs of
the operator.
When splitting wood, parts of the body may be crushed or separated due to
hydraulic knife lowering.
There is a risk of branchy wood getting stuck when being split. Please be
advised that the wood being separated is under heavy pressure and your fingers
may get squeezed in the gap.
Caution!
Pieces of wood cut at the right angle to be split only!
Diagonally cut pieces of wood may slip when cutting!
This may cause personal injury or damage to the splitter knife, especially
when using the gap extension by wedge!
Requirements for operating staff
The operating staff must carefully read the Operating Instructions before
using the appliance.
Qualification: Apart from the detailed instructions by a professional, no
special qualification is necessary for appliance use.
Minimum age: Persons over 18 years of age can only work on the appliance. An
exception includes youngsters trained in order to reach knowledge under the
supervision of the trainer during occupational education.
Training: Using the appliance only requires corresponding training by a
professional or the Operating Instructions. No special training is necessary.
Emergency procedure
Conduct a first-aid procedure adequate to the injury and summon qualified
medical attendance as quickly as possible. Protect the injured person from
further harm and calm them down. For the sake of an eventual accident, in
accordance with DIN 13164, a workplace has to be fitted with a first-aid kit.
It is essential to replace any used material in the first-aid kit immediately
after it has been used.
If you seek help, state the following pieces of information:
- Accident site
- Accident type
- Number of injured persons
- Injury type(s)
Maintenance
Unplug the machine before any work on it.
Carry out a visual inspection before any use to make sure the appliance,
especially the cutting tools, fastening parts, and the entire cutting unit are
not damaged. The appliance must not be used if damaged or if safety equipment
is defective. Replace any worn-out and damaged parts.
The hydraulic hoses and connections must be checked if tight enough after app.
4 hours of operation and tightened if necessary.
If the device is defective, the repair has to be made exclusively by customer
service. Use only original accessories and original spare parts. Never clean
the machine and its components with solvents, flammable or toxic liquids.
Us only a damp cloth making. Only a regularly maintained and treated
appliance can serve as a satisfactory aid. Insufficient maintenance and care
can lead to unforeseen accidents and injuries. If necessary, a list of spare
parts can be found at www.guede.com.
Symbols
| Read the Operating Instructions
---|---
Wear eye protective goggles!
Wear ear protectors!
Safety gloves to be used!
Safety shoes to be used
Use of crane
Caution! Moving parts of the machine!
To be operated by 1 person only!
Do not touch in the splitting area!
Protect against humidity. Never expose the tool to rain.
WARNING/Caution!
Dangerous voltage
Caution – hot surface!
The danger of burns!
Warning against hand injuries
Keep a distance from persons Observe to keep out of the dangerous zone.
Warning against thrown-off items
Warning against risk of tripping
Warning against hand injury by the splitter knife
Engine rotation direction
2 people are needed for implementation.
Any damaged or disposed of devices must be delivered to appropriate collection
centers.
Protect against humidity
This side up
Warranty
The warranty period of 12 months applies to commercial use and 24 months
applies to private use and commences on the day of purchase of the device.
Warranty applies exclusively to failures due to defective material or
workmanship. An original sale slip with an indication of the date of sale must
be presented in case of claiming the warranty rights.
warranty does not cover unprofessional use such as device overload, violent
use, damage caused by third parties or foreign materials, failure to comply
with operations and assembly manual, and normal wear and tear.
Important information for the customer
Please be sure to know that returning the product in or after the warranty
period must be made in the original packaging.
Service
Do you have any technical questions? Any claim? Do you need any spare parts or
operating instructions? We will quickly help you without needles bureaucracy
at our web pages at www.guede.com in the Servicing part. Please help us be
able to help you. In order to identify your device in case of claim we need
the serial No., product No. and year of production. All this data can be found
on the type label. Please enter it here for future reference:
Serial No.:
Art. No:
Year of production:
Tel.: +49 (0) 79 04 / 700-360
Fax: +49 (0) 79 04 / 700-51999
E-Mail: support@ts.guede.com
F ailur es
| C auses|
Removal
---|---|---
The engine does not start| No power in the socket| Check the fuse
Defective electric extension cable| Pull the plug out, check it, replace it
Wrong connecting cable| 5-wire connection at 2.5 mm2 cross-section
Defective condenser switch| Have the machine checked by a professional
electrician
Wrong engine rotation direction| Wrong connection| Use a screwdriver to turn
the phase-changing switch in the power supply
The splitting knife is not moving| Adjust the two-hand control and starting
levers| Defective control valve – to be replaced in a service center only
The splitter has no power| Wrong rotation direction| Have the rotation
direction changed by a professional
Few hydraulic oil| Hydraulic oil to be added
The trigger is bent; the hydraulic piston on the valve is not fully seated|
Check all screws on the trigger Adjust the trigger so that the hydraulic
piston on the valve is fully seated
Wood has many knobs and the splitting knife is getting stuck| Lubricate the
splitting knife
The control arm is bent| Put the control arm back to the starting position
The green supply button does not hold after being pressed| Defective fuse,
etc.| Check the cable
2-phase running
The hydraulic pump is whistling, split- ting knife running jerkily| Oil loss,
bottom contamination| Tighten the screws replace the hose
Few hydraulic oils| Hydraulic oil is to be added
GÜDE GmbH & Co. KG
Birkichstrasse 6
74549 Wolpertshausen
Deutschland
Tel.: +49-(0)7904/700-0
Fax.: +49-(0)7904/700-250
Email: info@guede.com
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>