MONODEAL Trucker Bluetooth Headset User Manual

MONODEAL Trucker Bluetooth Headset

Congratulations

please contact US by email at support@monodeal.net.

Package Contents

Product Overview

1. Headband
2. Release Button
3. Detachable Earpiece
4. Volume +
5. Phone Button/Play or Pause
6. Volume_ 7. Microphone
7. LED Indicator Light
8. MFB/Mute Button
9. USB-C Charging Port
10. Detachable Head Clamp

Specifications

1. Wireless Connection : 8T
2. 8T Version : V5.0
3. Wireless Frequency Band : 2.4 GHz
4. Supported Protocols: HSP, HFP, A2DP, AVRCP
5. Operation Range: 10 meters
6. Charging Time: approx. 2 hrs
7. Input: DC 5V== 0.5A
8. Battery Voltage: 3.7V
9. Transmission Power: 3 dBm

Pairing Methods A. BT Pairing

1. Turn on the Bluetooth on your phone.
2. Press and hold the MFB for 2 seconds to power on the headset. You will hear “Power on”.
3. Search and tap to connect to ” M103 ” on the Bluetooth list of your phone. Then you will hear “Paired. Your headset is connected.” The LED indicator will flash blue every 10 seconds after paired. The phone shows that ” M103 ” is connected.

Note : The headset can also be connected to a computer by following the above steps.

Switching to Unilateral Headset

1. Press and hold the Release Button and pull out the Detachable Earpiece.
2. Snap the Detachable Head Clamp into the slot to use the headset as a unilateral one.

To Pair with Two Phones

1.  Follow the above pairing guide to connect the headset to phone A, then switch off the Bluetooth function of phone A.
2. At this point, the headset automatically enters pairing mode.
3. Search and click to connect to “M103 ” on the Bluetooth list of phone B.
4.  After the headset is paired with phone B, switch on the Bluetooth function of phone A and tap “M103 ” to reconnect to the headset. Now the headset is connected with two phones.

Note : When the headset is paired with two phones, music can only be played from one. If you want to play music on the other connected phone, pause or stop playing the music on the previous one. If you want to answer a new call from the other connected phone, hang up the current call on the previous one.

Operations Instructions|

Charging the Headset

1. When the LED indicator flashes RED, please charge the headset.
2. Connect the US-C end of the charging cable to the headset and the USB-a end to a booted PC, charger, or power bank. The LED indicator lights in steady RED.
3. Charging is completed in about 2 hours. The LED indicator lights in steady BLUE when the headset is fully charged.

Notes

1. When the headset will not be used for a long haul, charge it at least once every 2 months.
2. It is not recommended to use the headset while charging. 3. When the every one lower than 3 3% you will hear Battery

LED Indicator Light

Voice Prompt

FAOS

1. Q: Can I use the headset while it is recharging?
   A: Yes, but extremely low battery or poor power quality may cause electrical noise. We do not recommend frequent use in this way as it will shorten the battery life.

2. Q: How to reconnect the headset and what to do when it fails to reconnect?

3. A:  When “M103 ” is paired with your device successfully, it will reconnect to the paired device automatically within 10 minutes every time it powers on. If the reconnection failed, please try pairing again. It will power off if reconnection failed over 10 minutes.

4. When the headset goes out of operation range, you will hear “Your headset is disconnected”. It will reconnect automatically after entering the operation range.

5. To avoid reconnection failure, keep the headset away from electromagnetic interference devices such as microwave ovens, Dase stations, etch

6. Q: What’s the password for pairing?
   A: Some devices may require a password for pairing. Try entering 0000. 8888, 1111, or 1234.

7. Q: What devices can recharge the headset?
   A: Any charger, car charger, power bank, PC, etc. with DC 5V/above 500mA output.

8. Q: What to do if I cannot turn the power on?
   A: Please try charge reset. Press and hold the MFB and connect the charging cable to charge the headset. After the charge reset, if the charging cable is not disconnected, the headset will reboot and function normally.

9. Q: What to do if I fail to pair the headset with my devices?

10. A Power off the headset. Disconnect and connect the USB dongle ordain, then power on the neediest

11.  Try charge reset.

12. If the above methods do not help, you may contact our customer service for more support

13. Q: Why does the headset power off automatically?
    A; When the headset is not connected over 10 minutes or the battery is too low. the headset wil power on automaticallv

IMPORTANT SAFETY INSTRUCTIONS-CAREFULLY FOLLOW THESE INSTRUCTIONS RETAIN THESE INSTRUCTIONS

1. This sheet contains important safety and operating instructions.
2. Before using the product, read all instructions and caution markings on the product, accessories, and device.
3. Keep the product away from the fire to avoid an explosion.
4. Do not place the product in or near an inflammable, explosive, or hazardous object.
5. Do not operate the product with a damaged cord or plug.
6. Do not operate the product if it has been damaged in any way.
7. Do not disassemble the product. Disassembly may result in a risk of safety
8. Do not throw or shake the product.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>