C Cattleya 120VAC/60Hz LED Wall Sconce Instruction Manual

C Cattleya 120VAC/60Hz LED Wall Sconce

Product Information: LED Wall Sconce
The LED Wall Sconce is a lighting fixture that can be installed using two different methods: plug-in installation or hardwire installation. It operates on a 120VAC/60Hz power supply and must be installed in accordance with local and National Electrical Code (N.E.C.) standards to prevent possible injury from electric shock. The product comes with a fixture body (C), a light bulb (B), a light shade (A), a rod (D), a crossbar assembly, plastic anchors (CC), wood screws (AA), a bushing with a rubber washer (DD), a wire connector (EE), and a mounting plate (F). The light bulb is not included in the package.

Product Usage Instructions

Before Installation
Turn off the main power at the circuit breaker before installing and servicing the fixture to prevent possible injury from electric shock. If you are unfamiliar with proper electrical wiring connections, obtain the services of a qualified electrician.

Plug-In Installation

1. Connect the rod (D) to the fixture body (C).
2. Install the light bulb(B).
3. Install the light shade (A).
4. Measure the distance between the two keyholes on the crossbar assembly. Mark the location of the two keyholes on the wall with a pencil, making sure the holes line up horizontally in the correct position. Drill a small hole (6 mm) on each mark and nail the plastic anchors (CC) into the wall using a hammer. Insert the two wood screws (AA) in the plastic anchors (CC) as shown.
5. Place the two keyholes on the fixture body’s crossbar assembly onto the two wood screws (AA). Make sure the two keyholes are secure on the two wood screws (AA) before letting go of the fixture body. Adjust the shade on the fixture body (D) to your desired location. Plug the power cord into the outlet.
6. Turn on the switch and enjoy.

Hardwire Installation

1. Remove the plug wire and rubber plug from the wire terminal.
2. Insert the bushing with a rubber washer (DD) in the hole on the backplate on the fixture body (C). Connect the rod (D) to the fixture body (C).
3. Wrap the supply ground wire around the green ground screw on the mounting plate (F), no less than 2 – in. from the end of the wire. Tighten the ground screw. Connect the fixture ground wire to the supply ground wire with a wire connector (EE). Insert Supply White Wire into the terminal hole marked with N, and Supply Black Wire into the terminal hole marked with L.
4. Reach the fixture body (C) on the mounting plate (F). Secure with the previously removed mounting balls (D).
5. Install the bulb (B) and lampshade (A) on the fixture body (C) in turn.
6. Turn on the switch and enjoy.

LED WALL SCONCE

READ AND FOLLOW SAFETY INFORMATION

CAUTION – Turn off the main power at the circuit breaker before installing and servicing the fixture to prevent possible injury from electric shock. All electrical connections must be in accordance with local and National Electrical Code (N.E.C.) standards. If you are unfamiliar with proper electrical wiring connections, obtain the services of a qualified electrician.
Note: This product has two installation methods for selection.

Installation method 1

Plug-in installation

1. Turn off the power before starting installation.Connect the rod (D) to the fixture body (C).
2. Install the light bulb(B).
3. Install the light shade (A).
4. Measure the distance between the two keyholes on the crossbar assembly. Mark the location of the two keyholes on the wall with a pencil (not provided), making sure the holes line up horizontally in the correct position. Drill a small hole (6 mm) on each mark and nail the plastic anchors (CC) into the wall using a hammer. Insert the two wood screws (AA) in the plastic anchors (CC) as shown.
5. Place the two keyholes on the fixture body’s crossbar assembly onto the two wood screws (AA). Make sure the two keyholes are secure on the two wood screws (AA) before leng go of the fixture body. Adjust the shade on the fixture body (D) to your desired location. Plug the power cord into the outlet.
6. Turn on the switch and enjoy.

Installation method 2

Hardwire installation

1. Turn off the power before starting installation. Remove the mounting plate from the fixture body (C) and keep the mounting plate (F) and two mounting balls (D) for later use.NOTE: Prior to installation, close or cover the sink drain and/or any vents near the installation site to prevent loss of mounting hardware if dropped. Use a screwdriver (not provided) to remove the iron sheets from the mounting holes on the mounting plate (F) as shown. Secure the mounng plate (E) to the outlet box (not included) with the outlet box screws (BB) as shown. Tighten until snug.
2. Remove the plug wire and rubber plug from the wire terminal.
3. Insert the bushing with a rubber washer (DD) in the hole on the backplate on the fixture body (C). Connect the rod (D) to the fixture body (C).
4. Wrap the supply ground wire around the green ground screw on the mounting plate (F), no less than 2 – in. from the end of the wire. Tighten the ground screw. Connect the fixture ground wire to the supply ground wire with a wire connector (EE). Insert Supply White Wire into the terminal hole marked with N, and Supply Black Wire into the terminal hole marked with L.
5. Reach the fixture body (C) on the mounng plate (F). Secure with the previously removed mounng balls (D).
6. Install the bulb (B) and lampshade (A) on the fixture body (C) in turn.
7. Turn on the switch and enjoy.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>