Arctic Cat Prowler Pro Falcon Ridge Enclosure Instruction Manual
- June 3, 2024
- FALCON RIDGE
Table of Contents
Arctic Cat Prowler Pro Falcon Ridge Enclosure
Instructions for Installation and Care of Arctic Cat / Textron Prowler
Pro Full Cab with Aero-Vent Windshield
AC-PRO-FC04
Notice: Do not smoke inside the cab or expose the enclosure to direct
flames. Cab is Flammable.
Be sure to read these instructions thoroughly before opening and installing the enclosure. The installation is best done when the temperature is 70 degrees F. or warmer. The temperature affects the adhesive Velcro, if conditions prevent installing in warmer weather it helps to store the adhesive Velcro at room temperature prior to installation.
-
Check over the parts included in the carton with the parts list shown below:
Soft Doors:
1″ Adhesive Velcro Strip 2 each 16” long
2″ Adhesive Velcro Strip 2 each 5” long
“ “ 2 each 8” long
“ “ 2 each 20” long
4 each 32″ long
4 each 34″ long
Snap studs 11 each ( 1 extra )
Door Panels 2 each
Rear Window:
2″ Adhesive Velcro Strip
“ “ 2 each 53” long
Top Cap:
36” Webbing Strap w/ Grommet 2 each
36” Webbing Strap w/ Loop 2 each
2″ Adhesive Velcro Strip 2 each 6” long
If any parts are damaged or missing please contact customer service at 606-845-7439. -
Begin by cleaning the roll cage and plastic that surrounds the doors. Using rubbing alcohol is preferable. This step is very important for the Velcro strips to properly adhere
-
Start with installing the Rear Window. The two 53” adhesive Velcro strips will go on the frame above and below the rear window. The Velcro will go on as shown in the photos on the next page. Make sure to center the strips.
-
Next install the 20” adhesive strips down each side of the Rear Window as shown in the photo below.
-
Now attach the Rear window to the frame making sure to center it correctly. When installing the doors the rear part of the door will attach to the sides of the Rear Window.
Soft Doors: -
Now start installation by placing the 2″ adhesive Velcro strips around the outside edges of the upper door frame. Starting at the front of the frame first place the 34″ strip as shown in the photo on next page.
-
Next place the 32″ strip across the top of the frame as shown below.
-
Next place the5″ strip in the rear corner as shown below.
-
After all the Velcro is in place take the door and place it on the vehicle. the following series of photos show how it should look after being installed.
-
Next attach the 8” adhesive Velcro strip to the bottom of the front top portion of the door as shown in the photos below.
-
Now take the 18” Strip that is 1” wide and place it on the inside front portion of the factory door. Then take the bottom front section of the soft door and wrap it around the factory door and attach the two together as shown in the photos below.
-
Lastly install the snap studs into the plastic for the bottom rear portion of thee door. It works best to put the screw studs into the snap sockets on the door first. Then one by one pull the door in place and push the screw into the plastic making sure to put enough pressure to leave a mark. Then remove the screw stud from the door and install it where the mark was left behind at. The following picture show what it looks like.
Aero-Vent Windshield: -
Install the windshield as per the included instruction
Top Cap:
-
Begin installation of the Top Cap by placing the webbing straps on the vehicle. The front straps will use the two straps with grommet holes. Remove the bottom two thumb nuts off the windshield and place the grommet end of the straps over the bolt and replace the thumb nut so it looks like the photo below.
-
In the rear of the vehicle take the two straps with loops sewn on one end and wrap them around the frame just above the frame bolts. There is a space here just under the cross frame that the strap will fit. Take the loop end and run it through first from the inside of the cab and them run the other end of the strap through the loop as shown in the photo below.
-
Now place the Top Cap over the frame so that the pointed side faces the front of the vehicle. Make sure that it is properly centered and run the straps through the buckles and pull it down tight. The straps should look like the photos below.
Cleaning and Storage Recommendations:
- Before removing the Cab for storage, make sure it is very clean in order to prevent scratching of the window panels. Clean with a soft rag or sponge using a mild liquid detergent soap and warm water solution. Never rub the windows with a dry cloth or rag! Let the Cab dry thoroughly before attempting to roll for storage.
- It is important that the Cab be rolled up for storage rather than folding. Folding will cause damage to the windows!!! Carefully roll up the Cab similar to the way it was when it was packed at the factory. On a large, clean and flat surface, fold the doors over the rear panel first, then, interleave the top and windshield on top of the doors. Begin rolling the Cab into a roll approximately 8 inches in diameter. Put the rolled Cab back into the carton for storage at a normal room temperature. It is best not to expose the Cab to either extreme hot or cold temperatures when storing.
- A special cleaner conditioner is available from Falcon Ridge that will greatly increase the service life of the Cab Enclosure. In addition, if additional hook and loop sets are needed, they can also be ordered.
Thank you for your purchase!
Return Policy
If for any reason you choose to return this product it must be returned within 30 days from date item is received. You MUST package the product exactly as it was originally packaged from the factory to get a full refund for the product!
The vinyl windows should never be folded when packaging in the box or for storage purposes. Lay all the windows on top of each other with the canvas folded in between and the paper (if available) on both sides of the windows.
All returned products will be inspected upon arrival at the production facility and must be in unused, factory new condition to receive refund – a 25% restocking fee will apply.
If ordered from Falcon Ridge please call at
606-845-7439 to gain a return
authorization number, use our preferred shipping carrier (UPS) to return the
item (unless the item is defective, you are responsible for paying the
shipping to return the item.) Any returns submitted to Falcon Ridge without a
return authorization number will be charged a 20% restocking fee. If ordered
from one of Falcon Ridge’s many distributors, you must first call them and see
what their return policy is. Once your item reaches our production facility,
our customer satisfaction team will inspect your item to ensure unused,
factory new condition.
NOTE: All windshields must be returned with the original protective film
intact and not removed. Do NOT REMOVE if you have any intentions of returning
the item. Refund/ replacement of a windshield will only be processed on items
with original protective film or if the windshield is defective.
Items must be properly packaged in the original shipping carton to protect them during transit and ensure your returned item arrives back factory fresh, and in new resalable condition (any returned items that have been used, altered or damaged in any way will not be subject for a refund.) All contents including instruction manuals, accessories, hardware, Velcro, etc. must be included in your return shipment. Only items in OEM factory new condition will be approved. Once returned items are received, credit will be issued to the original credit card/ payment method used for the purchase. Outbound shipping and return shipping cost will not be refunded. Please allow 4 to 6 weeks for your refund to be processed.
Warranty
To The Owner of this Product:
Thank you for purchasing one of our Falcon Ridge Cab Enclosures, Tops &/or
Windshields! Below are the terms under which your product is covered under our
manufacturer’s warranty.
30 Day Warranty which includes and is not limited to replacing the enclosure,
tops and/or windshield due to defect of the product. Please refer to the
return policy in this case for more information.
1 Year Warranty includes any defect in material or workmanship within this time frame we will gladly correct the problem or replace the enclosure, tops &/or windshield. Upon submitting for the correction or replacement we will need to receive pictures of the defect in material or workmanship along with the receipt from the date of purchase.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>