Aqara 3020317 Smart Wall Switch User Manual

Aqara 3020317 Smart Wall Switch

Product Information

The Smart Wall Switch (No Neutral, Single Rocker) is a smart switch that allows you to control your lights or other connected devices remotely. This product requires a compatible hub for operation. Some features may require a specific hub. For a detailed list of compatible hubs, please visit the AQARA support website.

Important safety precautions:

• A certain amount of electrical knowledge is required to install this smart wall switch. For your safety, it is recommended to seek assistance from a qualified electrician.
• This product is designed for indoor use only and should not be used in humid environments.
• Avoid installing this product near a heat source.
• Ensure that this Smart Switch is used with copper wire only.

Installation Instructions

1. Before starting the installation, turn off the power at the circuit breaker or fuse box and confirm that the power is off by switching the light on and off multiple times.
2. Remove the existing switch and identify the wires with wire labels:
   • Ground wire (usually green/bare)
   • Neutral wire (usually white)
   • Line(Hot)/Load wire (usually black)
3. Install the smart wall switch and connect the wires as required:
   • Connect the ground wire to the ground terminal of the smart switch.
   • Connect the neutral wire to the neutral terminal of the smart switch.
   • Connect the line (hot)/load wire to the corresponding terminal of the smart switch.
4. Tuck the wires into the wall box, leaving room for the smart switch. Use the provided screws to mount the smart switch to the wall box, being careful not to crush any wires. Avoid overtightening the screws.
5. Install the wall plate, turn on the main power at the circuit breaker, and test the switch by pressing the button. If it doesn’t work, check if the wiring is correct and if the power is restored.

Quick Setup

1. Add the Hub to the app according to the Hub Quick Start Guide.
2. Open the app and tap the “+” button in the top right corner to enter the Add Device (Accessory) page.
3. Select “Smart Wall Switch (No Neutral, Single Rocker)” and follow the instructions to add it to your app.
4. If the connection fails, try moving the hub closer to the switch, connect it to power, and try again.

Effective Range Test

To test the effective range of communication between the device and the hub, quickly press the button on the device three times. If the hub makes voice prompts, it indicates that the device can communicate effectively with the hub.

Indicator Light Description

• Blue light blinks quickly: Zigbee network is connecting.
• Blue light keeps on: Zigbee network works properly.
• Red light blinks quickly: High-temperature alarm.
• The red light blinks slowly: Zigbee network is not connected.

Specification

• Manufacturer: Lumi United Technology Co., Ltd.
• Address:  8th Floor, JinQi Wisdom Valley, No.1 Tangling Road, Liuxian Ave, Taoyuan Residential District, Nanshan District, Shenzhen, China.
• Online Customer Service: www.aqara.com/support
• Email:support@aqara.com

Product Profile

• This product requires a compatible hub. Some features require a specific hub.
• For the detailed list, please visit www.aqara.com/support.

Warning

1. A certain amount of electrical knowledge is required to install a smart wall switch. For your safety, we recommend that you ask a qualified electrician to help you install it;
2. This product is for indoor use only; do not use it in humid environment;2.
3. Do not install this product near a heat source;3.
4. IMPORTANT!: This Smart Switch is rated for and intended to only be used with copper wire.

Before you install

This product is only used to replace a single pole switch rather than a 3-way switch.

Installation

Visit www.aqara.com/support for more information.

1. Turn off the power at the circuit breaker or fuse box and test that power is off before wiring. (Please switch the light several times to make sure that the power has been disconnected)
2. Remove the existing switch and identify the wires with wire labels.
3. Install the smart wall switch and connect the wires as required.3.
4. Tuck the wires into the wall box leaving room for the smart switch.
   • Using the screws provided, mount the smart switch to the wall box.
   • Be careful not to crush any wires.
   • (Note: avoid overtightening the screws.)
5. Install the wall plate, turn the main power ON at the circuit breaker, and test the switch by pressing the button;
   • If it doesn’t work, please check: a. If the wiring is correct; b. If the power is restored.
   • If it works, add the switch to the app following the next steps;

Quick Setup

1. Please add the Hub to the app according to the Hub Quick Start Guide. Please open the app, and then tap “+” in the top right corner to enter
2. Add Device (Accessory)” page. Select “Smart Wall Switch（No Neutral， Single Rocker)”, and add it according to instructions.

If the connection fails, please move the hub closer to the switch, connect to power, and try again.
Effective Range Test: Quickly press the button on the device 3 times. If the Hub makes voice prompts, it indicates that the device can communicate effectively with the Hub.

Indicator Light Description

Specification

• Model: WS-USC01
• Dimensions: 120 x 74 x 36.5 mm (4.72 x 2.91 x 1.44 in)
• Wireless Protocol: Zigbee 3.0
• Input: 120 V AC 60 Hz
• Min Load: 3 W (Incandescent), 5 W (CFL/LED), typical load
• Max Load: 600 W (Incandescent), 200 W（CFL/LED), 1/4 HP
• Operating Temperature: 0 – 40° C（32 – 104° F)
• Operating Humidity: 0 – 95% RH, non-condensing
• Manufacturer: Lumi United Technology Co., Ltd. Address: 8th Floor, JinQi Wisdom Valley,
• No.1 Tangling Road, Liuxian Ave, Taoyuan Residential District, Nanshan District,
• Shenzhen, China.
• Online Customer Service: www.aqara.com/support
• Email: support@aqara.com

Federal Communications Commission (FCC) compliance statement

1. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
2. This device may not cause harmful interference.
3. This device must accept any interference received, including interference that may cause undesired operation.
4. Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.

NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and the receiver.
• Connect the equipment to an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

FCC Radiation Exposure Statement
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment.
This equipment should be installed and operated with a minimum distance of 20 cm between the radiator and your body.
This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.

IC: 22635-AK022 IC NOTICE TO CANADIAN USERS
This device contains license-exempt transmitter(s)/receiver(s) that comply with Innovation, Science, and Economic Development Canada’s license-exempt RSS(s). Operation is subject to the following two conditions:

1. This device may not cause interference.
2. This device must accept any interference, including interference that may cause undesired operation of the device.

This Class B digital apparatus complies with Canadian ICES‐003.
This device complies with RSS‐247 of Industry Canada. Operation is subject to the condition that this device does not cause harmful interference.
This equipment complies with IC radiation exposure limits set forth for an uncontrolled environment.
This equipment should be installed and operated with a minimum distance of 20 cm between the radiator and your body.
This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter

Important Safety Instructions

1. The maximum ambient temperature during use of the appliance must not exceed 40° C.
2. The appliance is suitable for moderate climates only.
3. The appliance does not require much attention. If you want to clean it, please use only dry clothes or a brush.

References

• Aqara Smart Device Product Support

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>