FALCON RIDGE Soft Door Kit for CFMOTO UForce 1000 Instruction Manual
- June 3, 2024
- FALCON RIDGE
Table of Contents
FALCON RIDGE Soft Door Kit for CFMOTO UForce 1000
Notice: Do not smoke inside the cab or expose the enclosure to direct flames. Cab is Flammable.
Be sure to read these instructions thoroughly before opening and installing the enclosure. The installation is best done when the temperature is 70 degrees F. or warmer. This is to allow the Velcro to stick to the roll cage better, if you must install outside in the cold it will help to warm the Velcro inside at room temperature until ready to install.
INSTALLATION INSRUCTION
-
Carefully open the carton and remove the rolled up Cab Enclosure on a large flat surface that is clean and free of dirt or other material that may soil or scratch the windows of the Cab.
-
Check over the parts included in the carton with the parts list shown below:
- 1″ Adhesive Velcro Strip 2 each 10” long
2″ Adhesive Velcro Strip 2 each 29” long
“ “ 2 each 26” long
“ “ 2 each 18” long
2 each 5″ long
Snap studs 24 each ( 2 extra )
Door Panels 2 each
- 1″ Adhesive Velcro Strip 2 each 10” long
-
Begin by Cleaning the roll cage and plastic that surrounds the doors. Using rubbing alcohol is preferable. This step is very important for the Velcro strips to properly adhere.
-
Now start the installation by placing the 2″ adhesive Velcro strips around the outside edges of the upper door frame. Starting at the front of the frame just above the rearview mirror, place the 26″ strip as shown in the photo below.
-
Next place the 29″ strip across the top of the frame as shown below.
-
Next place another 18″ strip down the rear bar as shown below.
-
Next place the 5″ strip just below the bracket along the back of the roll cage.
-
Last piece of Velcro will be the 10” strip that is 1” wide. This goes on the frame just behind the rear-view mirror as shown in the photo below.
-
Lastly install the snap studs into the plastic for the bottom portion of the door. It works best to put the screw studs into the snap sockets on the door first. Then one by one pull the door in place and push the screw into the plastic making sure to put enough pressure to leave a mark. Then remove the screw stud from the door and install it where the mark was left behind at. The following pictures show what it looks like.
Cleaning and Storage Recommendations
- Before removing the Cab for storage, make sure it is very clean in order to prevent scratching of the window panels. Clean with a soft rag or sponge using a mild liquid detergent soap and warm water solution. Never rub the windows with a dry cloth or rag! Let the Cab dry thoroughly before attempting to roll it for storage.
- It is important that the Cab be rolled up for storage rather than folding. Folding will cause damage to the windows!!! Carefully roll up the Cab similar to the way it was when it was packed at the factory. On a large, clean, and flat surface, fold the doors over the rear panel first, then, interleave the top and windshield on top of the doors. Begin rolling the Cab into a roll approximately 8 inches in diameter. Put the rolled Cab back into the carton for storage at normal room temperature. It is best not to expose the Cab to either extremely hot or cold temperatures when storing.
- A special cleaner conditioner is available from Falcon Ridge that will greatly increase the service life of the Cab Enclosure. In addition, if the additional hook and loop sets are needed, they can also be ordered.
Return Policy
If for any reason you choose to return this product it must be returned within 30 days from the date the item is received. You MUST package the product exactly as it was originally packaged from the factory to get a full refund for the product!
The vinyl windows should never be folded when packaging in the box or for storage purposes. Lay all the windows on top of each other with the canvas folded in between and the paper (if available) on both sides of the windows. All returned products will be inspected upon arrival at the production facility and must be in unused, factory-new condition to receive a refund – a 25% restocking fee will apply. If ordered from Falcon Ridge please call at 606-845-7439 to gain a return authorization number, use our preferred shipping carrier (UPS) to return the item (unless the item is defective, you are responsible for paying the shipping to return the item.) Any returns submitted to Falcon Ridge without a return authorization number will be charged a 20% restocking fee. If ordered from one of Falcon Ridge’s many distributors, you must first call them and see what their return policy is. Once your item reaches our production facility, our customer satisfaction team will inspect your item to ensure unused, factory-new condition.
NOTE:
All windshields must be returned with the original protective film intact and
not removed.
Do NOT REMOVE
If you have any intentions of returning the item. Refund/ replacement of a
windshield will only be processed on items with original protective film or if
the windshield is defective.
Items must be properly packaged in the original shipping carton to protect them during transit and ensure your returned item arrives back factory fresh, and in new resalable condition (any returned items that have been used, altered or damaged in any way will not be subject for a refund.) All contents including instruction manuals, accessories, hardware, Velcro, etc. must be included in your return shipment. Only items in OEM factory new condition will be approved. Once returned items are received, credit will be issued to the original credit card/ payment method used for the purchase. Outbound shipping and return shipping cost will not be refunded. Please allow 4 to 6 weeks for your refund to be processed.
Warranty
To The Owner of this Product:
Thank you for purchasing one of our Falcon Ridge Cab Enclosures, Tops &/or
Windshields! Below are the terms under which your product is covered under our
manufacturer’s warranty.
30 Day Warranty which includes and is not limited to replacing the enclosure,
tops, and/or windshield due to defects of the product. Please refer to the
return policy in this case for more information. 1 Year Warranty includes any
defect in material or workmanship within this time frame we will gladly
correct the problem or replace the enclosure, tops &/or windshield. Upon
submitting for the correction or replacement we will need to receive pictures
of the defect in material or workmanship along with the receipt from the date
of purchase.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>