LITEON NIU-LIGHT 802.11 b-g-n 1T1R 2.4GHz Module User Manual
- June 5, 2024
- LITEON
Table of Contents
LITEON NIU-LIGHT 802.11 b-g-n 1T1R 2.4GHz Module User Manual
Model: NIU-LIGHT
PRODUCT FEATURES
- IEEE 802.11b/g/n, 1×1 SISO 2.4 GHz
- Compact Form Factor: 30x17x1mm (PCB) ±0.1mm
- Integrated CPU, memory, MAC, DSSS/OFDM baseband, direct conversion RF radio, encryption
- CMOS and low-swing sine wave input clock
- Low-power with deep sleep and standby modes
- Integrated T/R switch, PA, and LNA
- HF/RoHS compliance
PRODUCT SPECIFICATIONS
MAIN CHIPSET
NXP 88MW320
FUNCTIONAL SPECIFICATIONS
PIN DEFINITION
MECHANICAL
WN3602M (3.3V)
RECOMMEND FOOTPRINT
ENVIRONMENTAL
Operating
- Operating Temperature: 0 to 70 °C
- Relevant Humidity: 5-90% (non-condensing)
Storage
- Temperature: -40 to 85 °C
- Relevant Humidity: 5-95% (non-condensing)
WARNINGS
FCC Statement
This equipment has been tested and found to comply with the limits for a Class
B digital device, pursuant to Part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates, uses and can radiate radio
frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
FCC Caution: Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate this equipment.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
This device and its antenna(s) must not be co-located or operating in conjunction with any other antenna or transmitter.
For product available in the USA/Canada market, only channel 1~11 can be operated. Selection of other channels is not possible.
FCC Radiation Exposure Statement
This equipment complies with FCC radiation exposure limits set forth for an
uncontrolled environment. This equipment should be installed and operated with
minimum distance 20cm between the radiator & your body.
ISED Statement
This device contains licence-exempt transmitter(s)/receiver(s) that comply
with Innovation, Science and Economic Development Canada’s licence-exempt
RSS(s). Operation is subject to the following two conditions:
- This device may not cause interference.
- This device must accept any interference, including interference that may cause undesired operation of the device.
ISED Radiation Exposure Statement:
This equipment complies with IC RSS-102 radiation exposure limits set forth
for an uncontrolled environment. This equipment should be installed and
operated with minimum distance 20cm between the radiator & your body.
The transmitter module may not be co-located with any other transmitter or
antenna.
For product available in the USA/Canada market, only channel 1~11 can be
operated. Selection of other channels is not possible.
This module is intended for OEM integrators under the following conditions:
- Ensure that the end-user has no manual instructions to remove or install module.
- This module is certified pursuant to Part 15 rules section 15.247 and RSS-247.
- This module has been approved to operate with the antenna types listed below, with the maximum permissible gain indicated.
4. Label and compliance information
Label of the end product:
FCC
The host product must be labeled in a visible area with the following ” Contains FCC ID: 2AIBX-NIULL”.
The end product shall bear the following 15.19 statement: This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
ISED
This transmitter module is authorized only for use in device where the antenna
may be installed such that 20 cm may be maintained between the antenna and
users. The final end product must be labeled in a visible area with the
following: “Contains transmitter module IC: 21700-NIULL” or “Contains IC:
21700-NIULL”
5. Information on test modes and additional testing requirements
This module has been approved under stand-alone configuration.
OEM integrator has be limited the operation channels in channel 1-11 for
2.4GHz band.
The separate approval is required for all other operating configurations,
including portable configurations with respect to Part 2.1093/RSS-102 and
different antenna configurations
The information on how to configure test modes for host product evaluation for different operational conditions for a stand-alone modular transmitter in a host, versus with multiple, simultaneously transmitting modules or other transmitters in a host can be found at KDB Publication 996369 D04.
OEM integrator is still responsible for testing their end product for any additional compliance requirements required with this module installed (for example, digital device emissions, PC peripheral requirements, etc.).
IMPORTANT NOTE: In the event that these conditions cannot be met (for example certain laptop configurations or co-location with another transmitter), then the FCC/ISED authorization is no longer considered valid and the FCC/IC No. cannot be used on the final product. In these circumstances, the OEM integrator will be responsible for re-evaluating the end product (including the transmitter) and obtaining a separate FCC/ISED authorization.
6. Additional testing, Part 15 Subpart B and ICES-003 disclaimer
Appropriate measurements (e.g. Part 15 Subpart B compliance) and if applicable
additional equipment authorizations (e.g. SDoC) of the host product to be
addressed by the integrator/ manufacturer.
This module is only FCC/ISED authorized for the specific rule parts 15.247, RSS-247 listed on the grant, and the host product manufacturer is responsible for compliance to any other FCC/ISED rules that apply to the host product as being Part 15 Subpart B/ICES-003 compliant.
7. The user manual of the end product should include:
FCC:
Any changes or modifications not expressly approved by the party responsible
for compliance could void the user’s authority to operate this equipment. The
antenna(s) used for this transmitter must be installed to provide a separation
distance of at least 20 cm from all persons.
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. The antenna(s) used for this transmitter must not transmit simultaneously with any other antenna or transmitter.
ISED:
This device contains licence-exempt transmitter(s)/receiver(s) that comply
with Innovation, Science and Economic Development Canada’s licence-exempt
RSS(s). Operation is subject to the following two conditions:
- This device may not cause interference.
- This device must accept any interference, including interference that may cause undesired operation of the device.
ISED Radiation Exposure Statement:
This equipment complies with IC RSS-102 radiation exposure limits set forth
for an uncontrolled environment. This equipment should be installed and
operated with minimum distance 20cm between the radiator & your body.
The transmitter module may not be co-located with any other transmitter or antenna.
Read More About This Manual & Download PDF:
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>