LITEON WPX8988 Ceiling-Mounted for Recessed T-Rail User Manual

WPX8988 Ceiling-Mounted for Recessed T-Rail
User Manual

Type A
Ceiling-mounted for Recessed T-rail Ceiling-mounted for Recessed T-rail (Width:24mm, 15116″)
Step 1. Assemble Tau bracket and 1.1311 screws to the AP.
Step 2. To notate the AP and insert the Thar MOS into the recessed Trail per am,/ direction shown in the diagram. Type A

Mounting on concrete wall or concrete ceiling with security bracket

Step 1. Dail two Wes with 32mm pitch a concrete wal
Step 2. treed pr3C.t4 anchors. wall bracket and 13’20 sow been:4 screws to the wall
Step 3. Assemble the housing bracket and M31 screws to the AP. Step 4. Insert the housing bracket at the beam into the will trade! on the wal and rotate the AP per arrow bed: On Shawn in the dear.

Instruction to release security bracket

Step 1. Push down release dip from both sides of the wan bracket
Step 2. Rotate AP counterclockwise to release from security & bracket.

Troubleshooting

The following table shows the status of the AP’s LED indicators.

WPX8988-1 LED Description

PWR| Blue| On: Power is ON and ready for operation
Off: Power is OFF
Amber| On: CPU or System Failed
 Blinking: System Initial or reset (Software self-testing and loading)
LAN 1| Blue| On: Good Link at 2.5Gbps
Blinking: Receiving/Transmitting data at 2.5Gbps from LAN port
Amber| On: Good Link at 100/1000Mbps
Blinking: Receiving/Transmitting data at 100/1000Mbps from LAN Port
LAN2| Blue| On: Good link at 2.5Gbps
Blinking: receiving/transmitting data at 2.5Gbps from LAN port
Amber| On: Good Link at 100/1000Mbps
Blinking: Receiving/Transmitting data at 100/1000Mbps from LAN Port
2.4G| Blue| On: Good link on 2.4GHz, off: radio disabled or off
Blinking: Receiving/Transmitting data from wireless LAN
Amber| Reserved
5G| Blue*| On: Good link on 5GHz, off: radio disable or off
Blinking: Receiving/Transmitting data from wireless LAN
Amber| Reserved

• Optional: Blue or Green
  If the AP fails to connect to the cloud server, please check the following:

  1. Ensure that the Ethernet cable is plugged into the LAN l(PoE) port, and LAN1 LED is NOT OFF.
  2. If the AP fails to get a valid IP address from the local DHCP server, ensure that the DHCP service is ENABLED on your router.
  3. Ensure there is Internet connectivity on the local LAN network to which the AP is connected

Getting AP online

Step 1: Power up
If using PoE, plug one end of the Ethernet cable into the PoE switch or injector and plug the other end into the LAN 1(PoE) port.
If using a power adapter (optional), insert the power adapter plug into the AC power outlet and the other end into the DC IN port of the AP
Step 2: Connect to the network
If using PoE, make sure the PoE switch or injector is connected to your LAN network with Internet access.
If using a power adapter, plug one end of an Ethernet cable into the LAN 1(PoE) port and the other end into an Ethernet port of your Switch or Router on the network. Step 3: Check the LED status
Wait for a few minutes until the Power LED turns solid Blue and LAN1 LED turns Blue or Amber. The AP is then online for operation.

| A4| UNIT| SCALE| SHEET| MODEL No.| for WPX8988
---|---|---|---|---|---|---
LIMITS UNLESS OTHERWISE NOTED| | MM| NON| 1(1)| PART NAME| QSG
X.+—| Χ.°+—| APPROVED| CHECKED| DESIGNED| PART No.| 5150000562M7| REV| A0
.X+—| Χ.°+—| | | Dereck _
_2021-09-13|
LITE-ON TECHNOLOGY CORP.
.ΧΧ -F—| .xx°+—
.ΧΧΧ+—| .ΧΧΧ°+—

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>