Little Chicks CK027 Sydney Toddler Bed Rail Installation Guide
- June 16, 2024
- Little Chicks
Table of Contents
Little Chicks CK027 Sydney Toddler Bed Rail
Product Information
Specifications
- Product Name: Sydney Bed Rail
- Model Number: CK027
- Standards: ASTM F2085-19 & 16 CFR 1224
FAQ
- Q: Can I use this bed rail with slat bed bases?
- A: Yes, this bed rail is compatible with both flat and slat bed bases.
- Q: How do I remove the cover for washing?
- A: To remove the cover for washing, reverse the assembly steps.
Product Usage Instructions
Assembly
- Unfold the frames (C).
- Join both middle and bottom tubes (D1 & D2).
- Join top tubes (B) together.
- Join top tubes (B) to the frame (C).
- Tip the fully assembled frame forward.
- Feed the cover onto your arm through the ‘bottom opening’ on the ‘closed’ end of the cover (A).
- Feed the cover over the bracket (E) and pull anchor (F) through. (Logo facing out)
- Stand the frame back up and evenly spread the cover over the whole frame.
- Zip the cover closed and secure both flaps around the frame with the hook and loop fabric.
- To remove the cover for washing, reverse the assembly steps.
Installation
- Position the bed rail (J) so there is a gap of at least 9in / 23cm from both ends of the bed.
- Tighten the straps (G) so that 2 anchor plates (F) are tight and flat against the side of the mattress.
- Tuck in any excess straps under the mattress.
- Once installed, check that the bed rail is properly fitted and secure.
Operation
- To open:
- To release the lock, simultaneously lift both tabs (H) on the bed rail brackets. Swing the bed rail (J) down.
- To close:
- Swing the bed rail (J) up against the mattress until the 2 tabs (H) click and lock into position.
IMPORTANT SAFETY INFORMATION
IMPORTANT KEEP FOR FUTURE REFERENCE
WARNING: SUFFOCATION AND STRANGULATION HAZARD
- Gaps in and around bed rails have entrapped young children and killed infants.
- NEVER use with children younger than 2 years old. Use ONLY with older children who can get in and out of adult bed without help.
- NEVER use in place of crib.
- NEVER use unless bed rail is tight against mattress, without gaps, and at least 9in / 23cm from headboard and footboard. Do not fill gaps with pillows, blankets, or other items that can suffocate children.
- NEVER use on toddler bed, bunk bed, water bed, or bed with inflatable mattress. Use ONLY on adult bed.
- Not suitable for beds with recessed baseboards or some slat beds.
- Discontinue use if damaged, broken, or if parts missing.
- This bedguard should not be used on a sleeping surface that is more than 23.6in / 60cm from the floor.
WARNING: ENTRAPMENT HAZARD
- NEVER use bed rail without properly securing bed rail to bed. Incorrect installation can allow bed rail to move away from mattress, which can lead to entrapment and death.
- Use only on Mattress:
- Width: 30-63in / 76-160cm,
- Length: 63-86. 5in / 160-220cm,
- Depth: 4-8.5 in / 10-22cm.
ASSEMBLY
PARTS LIST
- A 1 x Cover
- B 2 x Top tubes (frame)
- C 2 x Bed rail frames
- D1 Middle tubes
- D2 Bottom tubes
- E Brackets
- F Anchors
HOW TO ASSEMBLE
NOTE: To join all tubes, squeeze buttons and click into place.
- Unfold frames (C).
- Join both middle and bottom tubes (D1 & D2).
- Join top tubes (B) together.
- Join top tubes (B) to frame (C).
- Tip fully assembled frame forward.
- Feed the cover onto your arm through the ‘bottom opening’ on the ‘closed’ end of the cover (A).
- Feed the cover over the bracket (E) and pull anchor (F) through. (Logo facing out)
- Stand frame back up and evenly spread cover over the whole frame.
- Zip the cover closed and secure both flaps around the frame with the hook and loop fabric.
- To remove Cover for washing, reverse assembly steps.
INSTALLATION AND HOW TO INSTALL
INSTALLATION
PARTS LIST
- E Brackets
- F Anchors
- G Straps
- H Tabs
- J Bed Rail
HOW TO INSTALL
- Position bed rail (J) so there is a gap of at least 9in / 23cm from both ends of bed.
- Slide Brackets (E) under mattress.
- Slide Straps (G) under the mattress and out the other side.
- Tighten Straps (G) so that 2 Anchor plates (F) are tight and flat against the side of the mattress.
- 2 SAFETY ANCHORS
- SECURELY HOLD BED RAIL IN PLACE
- Flat & Slat bed bases
- Tuck in any excess straps under mattress.
- Once installed, check the bed rail is properly fitted and secure.
T-BAR
For use with Slat bed bases
- Before positioning under mattress, you must rotate T-Bar 90º
OPERATION
To open
- To release lock, simultaneously lift both Tabs (H) on bed rail brackets. Swing bed rail (J) down.
To close
- Swing bed rail (J) up against mattress until the 2 tabs (H) click and lock into position.
CARE & MAINTENANCE
- Regularly check bed rail to ensure it is assembled and fitted properly and securely. Adjust as required.
- Discontinue use if damaged, broken, or if parts missing.
- To remove cover for washing, reverse assembly steps.
- To wash cover: warm machine wash gentle cycle, air dry.
- To clean other parts, wipe with damp cloth using mild detergent.
TEE-ZED PRODUCTS, LLC ACCEPTS NO RESPONSIBILITY FOR ANY LOSS OR DAMAGE SUFFERED BY ANY PERSON AS A RESULT OF THE USE OR MISUSE OF THESE GOODS. IN THE CASE OF ANY DEFECT IN THE GOODS, TEE-ZED’S LIABILITY SHALL BE LIMITED SOLELY TO REPLACEMENT OF THE DEFECTIVE GOODS.
Contact
Little Chicks® products by • Los productos Little Chicks® por
- Tee-Zed Products, LLC,
- PO Box 1662, Jamestown, NC 27282 USA
- 336-454-5716
- Toll free: 1-888-271-6959
- info@littlechickssafety.com
Made in Xiamen, China.
Hecho en China.
©2021 Tee-Zed Products, LLC
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>