ASRock DeskMeet B660 Series 8 Litre Mini-PC Installation Guide
- June 5, 2024
- ASRock
Table of Contents
Quick Installation Guide
DeskMeet B660 Series
Package Contents
*The barebone system does not include memory, hard drive, WiFi module and M.2 SSD.
Screw Package
Rubber Foot x 4pcs, M.2 Screw x 3pcs, 2.5” HDD/SSD Screw x 8pcs, 3.5” HDD Screw x 9pcs (Countersunk Screw x 2pcs included), PWR Screw x 4pcs (Step Screw x 2pcs included), PCIe Card Screw x 2pcs, Foam Pad for Power Supply
Front View
Rear View
Motherboard Layout
Top View
Onboard Connectors
Screw Package
Attach the foam pad to this position of the power supply to avoid damaging the case.
Customization Options
Hardware Installation
A Begin Installation
| |
---|---|---
1. Remove the screw from the bottom
side of the case.| 2. Pull out the motherboard tray.| 3. Remove the PSU and
EPE Sponge.
B Installing the CPU
C Installing the CPU Fan and Heatsink
*\The DeskMeet B660 series supports both Intel CPU Box Fan (65W) and third-party CPU fan cooler.
Please note that the DeskMeet B660 series chassis has 54mm height limitation
for the CPU fan cooler.
D Installing Memory Modules
The DeskMeet B660 series requires DDR4 DIMM.
For dual channel configuration, you always need to install identical (the same brand, speed, size, and chip-type) DDR4 DIMM pairs.
E Installing the M.2 WiFi/BT Module and WiFi Antennas
| |
---|---|---
1. Insert the WiFi/BT module into the M.2 slot.| 2. Tighten the screw to
secure the module
to the motherboard.| 3. Attach the SMA Wi-Fi Antenna Cables to the module.
| |
---|---|---
4. Insert the SMA Wi-Fi Antenna Cables to the
designated holes. Make sure that the cable routing is organized as shown in
the illustration above.| 5. Insert the Wi-Fi Antenna Connectors to the
antenna ports on the rear panel| 6. Fasten the screw nuts to secure the
antenna connectors..
F Installing the Type 2280 Ultra M.2 SSD
| |
---|---|---
1. Locate the M.2 slot on the motherboard.| 2. Carefully insert the M.2 SSD
into the slot.| 3. Tighten the screw to secure the M.2 SSD to the
motherboard.
G Installing the 3.5-inch HDD
| |
---|---|---
1. Connect the SATA Data and Power
Cable to the HDD.| 2. Connect the SATA Data Cable to the SATA Connector on
the motherboard.| 3. Locate the drive mounting location.
Place a HDD and secure it with two screws.
4. Secure the HDD with three more screws.
Place a HDD as shown in the picture above. Then secure the HDD with four
screws.
*If you install a 3.5-inch HDD in this location, you won’t be able to install a graphics card
H Installing the 2.5-inch HDD/SSD
| |
---|---|---
1. Connect the SATA Data and Power Cable to the HDD.| 2. Connect the SATA
Data Cable to the SATA Connector on the motherboard.| 3. Locate the drive
mounting location. Place two 2.5-inch HDDs/SSDs.
4. Secure the HDDs/SSDs with eight screws.
Place one 2.5-inch HDD/SSD as shown in the picture above. Then secure the
HDD/SSD with three screws.
*If you install a 2.5-inch HDD/SSD in this place, you won’t be able to install a dual-slot graphics card, but a single-slot graphics card can be installed.
I Installing the Fan / Liquid Cooler
|
---|---
1. Place the fan as shown in the picture above.| 2. Secure the fan with four
screws.
If you install a fan in this location, you won’t be able to install a graphics card.
|
1. Place the single radiator liquid cooler as shown in the picture above.|
2. Secure the liquid cooler with four screws.
If you install a fan in this location, you won’t be able to install a graphics card.
J Installing the Graphics Card
|
---|---
1. Open the latch.| 2. Insert the graphics card into the PCIe slot on the
motherboard.
Then close the latch and secure it with two screws.
K Complete
| |
---|---|---
1. Fasten the two step screws.| 2. Put the PSU back to the case.| 3. Move
the PSU in the direction shown above.
| |
---|---|---
4. Secure the PSU with two screws.| 5. Slide the motherboard tray back to
the chassis.| 6. Secure the screw at the bottom side of the case.
How to Remove the Motherboard from the Case
| |
---|---|---
1. Remove the six screws securing mother board to the case.| 2. Open the I/O
cover. Then remove the motherboard from the case.| 3. Complete.
How to Install the Motherboard
| |
---|---|---
1. Re-place the motherboard back to the case.| 2. Close the I/O cover.| 3.
Refasten the six screws that you removed earlier.
Support
Please visit our website at http:/www.asrock.com for:
A list of tested memory, M.2, 2.5” SATA HDD, wireless interface cards, and
operating systems that are supported; for information about downloading the
latest driver and BIOS updates; as well as the latest product support
information.
Equipment name: PC Type designation (Type): DeskMeet series
Unit| Restricted substances and its chemical symbols
Lead (Pb)| Mercury (Hg)| Cadmium (Cd)| Hexavalent
chromium
(Cr +6)| Polybrominated
biphenyls (PBB)| Polybrominated
diphenyl ethers
(PBDE)
Plastic Case| 0| 0| 0| 0| 0| 0
PCB| 0| 0| C| 0| 0| 0
Power Supply| 0| 0| C| 0| 0| 0
CPU Fan| 0| 0| 0| 0| 0| 0
Note 1: “Exceeding 0.1 wt %” and “exceeding 0.01 wt %” indicate that the
percentage content of the restric ed substance exceeds the reference
percentage value of presence condition.
Note 2: “o” indicates that the percentage content of the restricted substance
does not exceed the percentage of reference value of presence.
Note 3: The “—” indicates that the restricted substance corresponds to the
exemption.
Warranty Term
- Warranty of host of DeskMeet series personal computer (casing excluded): 1 years
- Warranty of transformer: 1 year
- Our warranty does not cover the casing of the product, fastenings, screws or packaging accessories.
- Data stored in the product may be lost as a result of the repair work or re-formatting of the hard drive disk. ASRock does not provide data recovery services or data storage. Please back up your data regularly to protect the data and avoid loss. For details of our warranty terms, please refer to the individual warranty statement applicable to the district where your product was bought.
Safety & Regulatory Information
Failure to use the included Power Supply may violate regulatory compliance and may expose the user to safety hazards.
P/N: 15G067046000AK
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>