Westinghouse 7784140 Radio Frequency Remote Control for Ceiling Fans User Manual

Westinghouse 7784140 Radio Frequency Remote Control for Ceiling Fans

Safety Tips

CAUTION: Read these instructions carefully, as incorrect wire connections will damage the receiver unit.  Before making any electrical connections, ensure the supply is isolated at the fuse or breaker protecting the circuit to be worked on. Double check the supply is isolated. NOTE: This remote control is suitable for connection to both types of wiring systems used with Westinghouse ceiling fans. Refer to ceiling fan instructions for choice of wiring connections.

1. Turn off power at fuse box to avoid possible electrical shock.
2. After hanging fan onto the mounting bracket, make sure plug connectors from the ceiling fan and terminal block (1) are moved away from the space located above the downrod ball (2). Slide the remote receiver into the space above the downrod ball as shown.
3. While fan is hanging on bracket, plug 4-pole connector from the mounting bracket into the 4-pole plug connector from the remote receiver (1). Plug the 4-pole plug connector from the remote receiver into the 4-pole plug connector from the fan (2). Attach the ground wire (3) from the downrod to the mounting bracket.
4. NOTE: If your ceiling fan is not equppied with connector plugs as used in step 3, carefully cut off plugs provided on the receiver unit and wire this unit as shown in the following step. NOTE: For this type of installation, you will need to purchase an 7-way strip connector (not included). NOTE: After wiring is complete, neatly bundle any excess electrical wires and carefully push them into the ceiling fan canopy, making sure to keep electrical connections in tact. Complete the normal ceiling fan installation procedures, following the instructions provided with your ceiling fan.

5. B	Color	Comment
   1	Brown	Supply Live
   2	Blue	Supply Neutral
   3	Green/Yellow	Supply Ground
   4	Blue	Neutral to Fan
   5	Brown	Live to Fan
   6	Orange	Live to Fan Light
   7	Green/Yellow	Ground to Fan
   8		Live from House
   9		Neutral from House
   10	Green/Yellow	Ground from House
   11	Blue	Neutral from Fan
   12	Brown	Live from Fan
   13	Orange	Live from Fan Light
   14	Green/Yellow	Ground from Fan

6. Note: Make sure to wire the 7-way strip correctly, matching the corresponding numbers shown in the drawing. After installation, it must comply with the requirement of double insulation or reinforced insulation.

IMPORTANT: When receiver installation is complete, switch the wall switch on, press button “ ” on the remote transmitter, and set the fan speed to high speed, using the fan pull chain control. Next, press the light button on the remote transmitter for light control. If the ceiling fan light does not come on, pull the ceiling fan light control pull chain once to activate the light. Once settings are completed, do not disturb the ceiling fan pull chain controls. Note: The ceiling fan light will come on automatically when you turn on the wall switch whether you turn off the light by remote control or not. To reverse the direction of the ceiling fan, use the switch on the fan unit. DO NOT REVERSE THE FAN WHILE IN OPERATION, as damage to the control unit of fan can result.

Restore electrical power to the outlet box by turning on the electricity at the main fuse box. To make the fan operational, open battery door by pressing and sliding down the battery door. Install two AAA 1.5V batteries (not included) into the hand-held remote transmitter (if not used for long periods of time, remove the batteries to prevent damage to the transmitter).

1.  The remote control adopts RF wireless digit emission technique, biunique controlled.
2.  The transmitter and receiver are matched at the factory. Please follow the next step to repair when thepairing is failed.
3.  Turn off the fan power and then restore it, press and hold the “fan stop” button for 5 seconds, within 60 seconds after you restore the power, the fan will automatic turn on at low speed and then turn off, with the light flashing 3 times. (NOTE: The pairing process is not accepted after 60 seconds when you restore supply power)
4.  Please note that the transmitter can pair with multiple receivers. When the transmitter does not control the receiver, please check if any similar remote controls are working nearby, disconnect them and then proceed with pairing process again.
5.  Store the remote transmitter away from excessive heat or humidity.
6.  Low power of battery or not-used for long time should be replaced.

The remote buttons function as follows

• Fan speed:
  • High speed
  • Medium-high speed
  • Medium Speed
  • Low Speed
• Button: Turn the fan off
• Light On/Off – press and release light button.
  •  Light Dimmer – continuously press the light button to brighten the light.
  •  Light Dimmer – continuously press the light button to dim the light.

Mount the transmitter holder onto the wall using screws provided. Place the transmitter into the holder.

The declaration of conformity can be downloaded from our following website: www.westinghouselighting.eu

References

• Ceiling Fans | Lighting Fixtures | Lamps

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>