CREATE Windlight Fold DC Ceiling Fan User Manual

CREATE Windlight Fold DC Ceiling Fan

Thank you for choosing our ceiling fan. Before using the appliance, and to ensure the best use, please read these instructions carefully.The safety precautions included in this document reduce the risk of death, injury, and electric shock when properly followed. Keep the manual in a safe place for future reference, along with the complete warranty card, sales receipt, and package. If applicable, please forward these instructions to the next owner of the appliance. Always follow basic safety precautions and accident prevention measures when using an electrical appliance. We do not assume any responsibility for the breach of these requirements by the customer.

LIST OF PARTS

Carefully open the packaging and remove all included items. Place them on a rug or a large piece of plastic to avoid any damage. Check that all the items listed below have been included.

SAFETY INSTRUCTIONS

• When using any electrical appliance, basic safety precautions should always be observed.
•  Read this entire manual carefully before beginning installation. Save these instructions.
• Use only original spare parts.
•  To reduce the risk of personal injury, connect the fan directly to the building support struc­ture in accordance with these instructions and use only the supplied hardware.
• To avoid possible electrical shock, before installing your fan, disconnect power by turning off the circuit breakers in the outlet box and the associated wall switch location. If you cannot lock the circuit breakers in the off position, securely attach a prominent warning device, such as a tag, to the service panel.
• All wiring must be in accordance with national and local electrical codes and ANSI/ NFPA 70. If you are unfamiliar with wiring, contact a qualified electrician.
•  To reduce the risk of personal injury, do not bend the blade clamping system when install­ing, balancing, or cleaning the fan.
•  Never insert foreign objects between the rotating fan blades.
• To reduce the risk of fire, electric shock, or motor damage, do not use a solid-state speed control with this fan. Use only original speed controls.
• This appliance can be used by children from 8 years of age and by people with reduced physical, sensory or mental capacities or lack of experience and knowledge if they have received supervision or instructions on how to use the appliance safely and understand the dangers involved. Children must not play with the appliance. Children should not perform cleaning or maintenance unless they are over 8 years old and supervised. Close supervision is necessary when any appliance is used by or near children.

NOTE:
The important safety precautions and instructions in the manual are not intended to cover all possible conditions and situations that may occur. It should be understood that common sense and caution are necessary factors in the installation and operation of this fan.

INSTALLATION INSTRUCTIONS

Mark the correct position of the holes and fix the ceiling bracket using the screws with metal plugs or screws and washers suitable for the type of ceiling chosen. Check the correct installation of the bracket before hanging the fan. This plate must support the full weight of the fan.

INSTALLATION PREPARATION

• To avoid personal injury and damage, make sure the place to hang the sheets leaves a clearance of 2.3 m from the ground and 76 cm from any walls or obstructions.
• Make sure the mounting bracket is securely attached to the building structure and can support the full weight of the fan.

DOWNLOAD INSTALLATION

• Remove the seat post bolt by removing the pin and pass the finial (crown molding) and hood through the hanger bar. Next, route the fan motor wires through the inside of the hanger bar. Tighten the hanger bar to the engine and insert the bolt and pin.

Angle mounting is recommended for a vaulted or angled ceiling. The standard mount hangs from the ceiling using a rod.

FIXING THE MOUNTING BRACKET

• The outlet box and beam must be securely mounted and capable of reliably supporting at least the weight of the fan.

Wooden ceiling
Securely attach the mounting bracket with wood screws and washers to the ceiling joints.

Concrete ceiling
Drill holes with an 8mm drill, Depending on the length of the expansion screws. Next, secure the mounting bracket to the ceiling with the expansion screws.

ASSEMBLING AND HANGING THE FAN

Tip:
To make it easier to feed the wires into the bar, wrap some electrical tape around the wires. This will help you hold them together as you insert them into the bar.

•  Loosen set screws and washer on top of motor housing. Remove the pins from the bar (if you haven’t already). Insert the rosette through the bar.
• Pass the cables through the bar and pull the excess cables from the top of the bar to tight­en them.
•  Place the bar inside the motor housing and insert the pins you removed earlier. Tighten the set screws and washers.
•  Lower the rosette onto the motor housing.

REMOTE CONTROL

1. Light
2.  On I off button
3.  Fan intensity control
4. Timer
5. Batteries (2 x AAA)
6. Color temperature control
7.  Inverse function
8. Fan intensity control

REMOTE CONTROL CONNECTION

Make the connection between the receiver wires and the fan motor wires following the color indications. Make sure the connection is firm.

REMOTE CONTROL RECEIVER PLACEMENT

CANOPY ASSEMBLY

• Raise the rosette up to the mounting bracket and align the loosened screws in the mount­ing bracket with the holes in the rosette.
•  Rotate the fin to adjust. Reinsert the screws and secure with a screwdriver.
•  Once you have the mounting bracket secured to the junction box you can proceed to hang the fan.
•  Hold the fan firmly with both hands. Pass the rod through the mounting bracket opening and let the ball rest on the mounting bracket.
• Rotate the ball coupling until it lines up with the tab on the mounting bracket.
•   Tip:
  Someone else should help you hold the ladder and hand you the fan after you get on it.

BLADES ASSEMBLY

• Align the holes in the fan blade holder with the holes in the fan blades and motor body and screw them into place, but do not tighten until they are all in place and screwed down.
  Tip:
  To save time, you can put the washers on each screw before installing the blades.

•  Lock the fan blade to the iron plate A with screws. Do not lock it tightly until three blades have been attached.

• Fasten the iron plate B to the motor with screws. Do not lock it tightly until all iron plates Bare attached.

• Install the blades on the motor and go to the next step.

CONNECTIONS PANEL ASSEMBLY

Hook the connection plate to the bottom of the fan by inserting the screw heads into the designated holes. Screw in the screws and then secure.

CEILING FAN WITH LED LIGHT

DECORATIVE COVER ASSEMBLY

Connect the single-pin plugs on the backplane with those on the LED panel. The LED panel is magnetized so it will be attached to the patch panel simply by snapping them together.
Tip:
While installing or removing the LED board, keep the insulation pads intact carefully. Turning the set screws too hard or too quickly will damage the insulation pads. Screw the lampshade back onto the connection plate.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>