YELLOW JACKET 67068 YJack Mano Wireless Dual Port Manometer User Guide
- June 5, 2024
- YELLOW JACKET
Table of Contents
- YELLOW JACKET 67068 YJack Mano Wireless Dual Port Manometer
- Power on Y JACK MANO™ device and connect to
- To view the static pressure readings on the Display Screen, select the
- For remote viewing of readings, launch the YJACK VIEW™ app, select the
- YJACK MANO™ measurement range and resolution designed for HVAC
- When finished, power devices off and store in a dry, temperature
- Read User Manual Online (PDF format)
- Download This Manual (PDF format)
YELLOW JACKET 67068 YJack Mano Wireless Dual Port Manometer
Power on Y JACK MANO™ device and connect to
Press and hold the “ON/OFF” button to power the YJACK MANO™ on. Release the “ON/OFF” button when the display changes and the “Y J” logo disappears
Note the Bluetooth® ID on the back of the device, this ID will be used to assign the device readings in the YJACK VIEW™ app. Connect the tubing to the appropriate ports and system fittings Supply Port (Blue); Return Port (Red)
To view the static pressure readings on the Display Screen, select the
desired settings.
To CHANGE A SETTING:
- Tap the corresponding button to highlight the current setting
- Continue to tap this button until the desired value is displayed
- Press and hold this button for 2 seconds to confirm the new setting- the setting will be confirmed and the highlighting will 7o\rmJ~-~~@ disappear when the button is released
DISPLAY: Select from several notification options. To change the background, press and hold for three seconds to inverse LCD mode.
ON/OFF: Power on and off, select from four auto-off timer settings.
POWER SAVING MODE: Powers off display after 15 minutes of inactivity to
extend battery life while viewing readings remotely.
Press any button to refresh the display
For remote viewing of readings, launch the YJACK VIEW™ app, select the
desired settings and Static Pressure session type. There is no Bluetooth® pairing required
YJACK MANO™ measurement range and resolution designed for HVAC
applications.
PRESSURE MEASUREMENTS
- When performing single input pressure measurements, use the positive(+) port input fitting located to the top (blue) when looking at the front face of the manometer. Positive pressures will display as positive results; negative pressure will display a negative result.
- To measure pressures with respect to the ambient area, place the end of the tube connected to the positive port to the area to be measured and leave the negative port(-) open. The display will show the pressure with respect to the ambient area where the meter is located.
- To measure differential pressures, connect tubes to both the positive and negative ports. Place the end of the tube connected to the positive port in the area expected to have a higher pressure and the end of the tube connected to the negative port in the area where a lower pressure is expected. The pressure difference between the two areas will be displayed on the manometer.
OVER PRESSURE INDICATOR: The display will flash if the pressure exceeds
60 inches of water (positive or negative).
Disconnect the manometer immediately. The manometer will not be damaged as
long as the pressure does not go above the maximum rated pressure.
AUTOMATIC SHUT-OFF: The manometer turns itself off after approximately 10 minutes. If this happens when connected to a pressure source, simply turn it back on. Correct readings will resume without disconnecting the pressure source.
NEGATIVE READINGS: The minus sign on the display indicates that the pressure measured is below atmospheric pressure.
When finished, power devices off and store in a dry, temperature
controlled* area
*Storing they JACK MANO™ device in extreme cold or heat can severely impact the battery life and display refresh rate.
YJACK MANOTM Accessories
UPC# | Description |
---|---|
78053 | 1/8″ NPT Brass Regulator Fitting |
78054 | Slide Gas Adapter (for 5/16″ Pressure Tap Boss) |
78072 | 30″ x 1/8″ ID Clear Tubing |
78073 | (2) Static Pressure Tips |
78074 | Soft Case |
For additional information, please see the digital YJACK™ user manual located at www.yellowjacket.com. Visit the app store or follow the QR codes below to download the YJACK VIEW™ app
Ritchie Engineering Company/ YELLOW JACKET® • Customer Service 1-800-769-8370 or 952-943-1300 • www.yellowjacket.com