INVENTUM VWM9001W Washing Machine Instruction Manual
- June 3, 2024
- INVENTUM
Table of Contents
INVENTUM VWM9001W Washing Machine
safety instructions
Symbols used in this document
Please read these instructions before operating the appliance and store them for future use. Please, do not use the washing machine without reading the instructions for use first.
- Check for any damage to the packaging or the appliance that may have occurred during transportation. Never use a damaged appliance, but contact your supplier.
- Failure to observe the instructions for use or inappropriate use of the appliance may result in damage to the laundry or the appliance, or injury to the user. Keep the instruction manual in a convenient location, near the appliance.
INSTALLATION LOCATION AND SURROUNDING AREA
- Keep the appliance clear from heat sources and direct sunlight to prevent plastic and rubber parts from corroding.
- The room where this appliance will be placed may not be warmer than 35°C.
- Do not install the appliance in a room where the temperature can drop below 5°C, as the parts of the appliance may become damaged when water freezes. Do not install the appliance in humid environments or rooms containing explosive or caustic gas. In case of water leakage or water splashes, allow the appliance to dry in the open air.
- Never use flammable sprays or substances in the immediate proximity of the appliance.
INSTALLATION
- Place the appliance on a solid (concrete) base that is level and stable.
- Adjust the adjustable feet to ensure the appliance is standing level and balanced.
- Before first use of the appliance, remove the transport bolts, as switching on a blocked appliance can result in serious damage. In such a case, the manufacturer shall not be
- able for any resulting damage.
- Before connecting the appliance to the power mains, wait at least 2 hours to allow it to reach room temperature.
- The door cannot be opened during operation of the washing machine.
- Before washing clothes for the first time, the appliance should be operated once with a full programme without any clothes inside.
- After the washing cycle, close the water tap and pull the plug from the power socket. Never pull the cord itself.
- Dispose the packaging materials according to local regulations. Keep the material out of reach of children. Danger of suffocation.
ELECTRICAL INSTALLATION
- Connect the appliance to a earthed power socket protected by a fuse that complies with the values on the rating plate.
- Particularly make sure that the appliance is not placed on the power cord.
To avoid danger, a damaged power cord may only be replaced by the
manufacturer, its service agent or similarly qualified persons. If the
appliance is damaged, it must not be operated until it is repaired by the
manufacturer, its service agent or similarly qualified persons. The appliance
may not be connected to the power mains using
an extension cord. Do not connect the appliance to the power mains using an
external switch device such as a program timer, or connect it to a power main
that is regularly switched on and off by the power supply provider.
- Do not connect the appliance to an electrical outlet intended for an electric shaver or hair dryer.
- The mains plug must be accessible after installation.
Never use an extension cord or multiple plugs for making a connection. Do not pull the plug out of the power socket if there is flammable gas around. Never pull out the plug with wet hands. Always unplug the appliance when it is not being used and close the water tap.
- Connection to water and power supply has to be executed by an adequately trained technician or expert.
- Any repair and maintenance pertaining to safety or performance should be done by trained experts.
- In case of a defect, only use approved spare parts by authorised manufacturers.
- In case of incorrect appliance connection, incorrect use, or servicing by an unauthorised person, Inventum will not be responsible for any damage, as such damage will not be covered by warranty.
WATER INSTALLATION
- The appliance is equipped with a single inlet valve and can be connected to the cold water supply only.
- To connect the appliance to the water supply, make sure to use the supplied water supply hose and gaskets. The water pressure has to be between 0.05 and 0.8 MPa (0.5 – 8 bar).
- Always use the supplied new water supply hose to connect the appliance to the water supply; do not reuse an old water supply hose.
- The end of the water discharge hose should reach into a water drain line.
- Check the connections of the water supply hose, the water tap and the water discharge hose for possible problems due to changes of water pressure. If the connections loosen or leak, close the water tap and get it repaired. Do not use the appliance before the pipes and hoses are installed properly by authorised persons.
At higher washing temperatures, the door glass will heat up. Be careful to
avoid burns. Keep children and animals far away from the machine while it is
operating. Do not remove the drain pump filter while there is still water in
the appliance. Big quantities of water can leak out, and there is a risk of
scalding due to hot water.
WATER OVERFLOW PROTECTION
- If the water level in the appliance rises above normal level, then the excess water level protection will be activated. It will shut off the water supply and start pumping out the water. The programme is interrupted and an error is reported.
CHILD SAFETY
- Before closing the appliance door and running the program, make sure there is nothing except laundry in the drum (e.g. check if a child or animal climbed into the drum of the appliance).
- Keep the detergents and softeners out of reach of children.
- Do not let children aged 3 years and under come near the appliance, unless they are under constant supervision.
- This appliance may be used by children aged 8 years and above and by persons with reduced physical, sensory or mental capabilities or lack of experience and knowledge, provided they are supervised or have been given instructions concerning the use of the appliance in a safe way and understand the hazards of inappropriate use. Children are not allowed to play with the appliance.
- The appliance may not be cleaned or maintained by children, unless this is done under supervision.
- Children should be supervised to prevent them from playing with the appliance.
- Do not climb or sit on the appliance.
- The appliance is made in compliance with all relevant safety standards.
OPERATION AND MAINTENANCE
Do not use detergents that contain solvents as this could lead to release of poisonous gases, damage to the appliance, and risk of fire and explosion.
- Only use the appliance for washing laundry as described in the instruction manual. The machine is not intended for dry cleaning.
- Only use agents for machine washing and care of laundry. Inventum will not be responsible for any damages or discoloration of gaskets and plastic parts resulting from incorrect use of bleaching or coloring agents.
- In case of a defect, only use approved spare parts by authorized manufacturers.
- Make sure that all pockets are emptied. Sharp and rigid items such as coins, brooches, nails, screws, stones etc. may cause serious damages to this machine.
- Remove all objects from pockets such as lighters and matches before using the appliance.
- Fabric softeners or similar products should be used as recommended in their instructions.
- Never try to open the door by force. The door will unlock shortly after the end of a cycle.
- Please do not close the door with excessive force. If it is found difficult to close the door, please check if the clothes are properly inserted and distributed.
- In case of incorrect connection of the appliance, incorrect use, or servicing by an unauthorised person, the user shall bear the cost of any damage, as such damage shall not be covered by warranty.
- When cleaning the appliance, only use non-corrosive descaling agents. Follow the instructions of the manufacturer of the cleaning agent. Finish the descaling process with several rinse cycles in order to remove any residual acid (e.g. vinegar etc.).
- The warranty does not cover consumables, minor deviations in colour, increased noise that results from appliance age and which does not affect the functionality of the appliance, and aesthetic defects on components, which do not affect the functionality and safety of the appliance.
TRANSPORT/RELOCATION AFTER INSTALLATION
- If you intend to move the appliance after it has been installed, it should be blocked by applying at least one transport bolt. Before applying the transport bolt, disconnect the appliance from the power mains.
- Accumulated water must be drained out of the appliance.
- The appliance is heavy. Transport with care. Never hold any protruding part of the appliance when lifting. The door of the appliance cannot be used as a handle.
INTENDED USE
- The appliance is intended solely for household use. If the appliance is used for professional, commercial purposes or purposes exceeding normal use in a household, or if the appliance is used by a person who is not a consumer, the warranty period shall be equal to the shortest warranty period required by relevant legislation.
- This appliance is intended to be used in households and similar applications such as:
- staff kitchen areas in shops, offices or residential type environments;
- farmhouses;
- by clients in hotels, motels and another residential type environments;
- bed & breakfast type environments;
- areas for communal use in blocks of flats or in launderettes.
- The appliance is not intended for use by persons (including children) with physical or mental impairments, or persons lacking experience and knowledge. These persons should be instructed about the use of the appliance by a person responsible for their safety.
OLD APPLIANCE
- Remove the door or deactivate the lock when disposing of the appliance. Children are known to have gotten themselves locked in old appliances. To prevent such a situation, break the door lock of your appliance and tear off the electrical cables.
This marking indicates that this product should not be disposed of with other household wastes throughout the EU. To prevent possible harm to the environment or human health from uncontrolled waste disposal, recycle it responsibly to promote the sustainable reuse of material resources. To return your used device, please use the collection systems or contact the retailer where the product was purchased. They return and can take this product for environmental safe recycling.
product description
FRONT
- Control unit
- Start/pause button
- Program selector knob
- On/off/reset button
- Dispenser tray
- Door
- Rating plate
- Pump filter
BACK
- Water supply hose
- Power cord
- Water discharge hose
- Adjustable feet
installation and connection
UNPACKING THE APPLIANCE
WARNING!
- Move the appliance with at least two people and wear protective clothing, such as sturdy gloves.
- When removing the packaging, make sure not to damage the appliance with a sharp object.
- Packaging material (e.g. films, Styrofoam) can be dangerous for children.
- There is a risk of suffocation! Keep all packaging away from children.3
REMOVING THE BLOCKING RODS
WARNING! Before first use of the appliance, the transport bolts must be
removed from the back of the appliance. A blocked appliance may become damaged
when it is switched on for the first time. The warranty does not apply in
cases of such damage!
- Remove the hoses and undo the screws on the back of the washing machine. Remove the two angular pieces.
- Slide the angular pieces onto the groove in the blocking rod; before doing so, rotate the right angular piece to the opposite side.
- Use the angular pieces to rotate the blocking rods by 90° and pull them out.
- Cover the two holes through which the blocking rods were inserted with plastic plugs, and redo the screws that you undid in step 1. The plastic plugs are supplied in the bag with the washing machine instruction manual.
MOVING AND TRANSPORTING AFTER INSTALLATION
If you wish to move the washing machine after it has been installed, the
angular pieces and at least one blocking rod have to be re-installed to
prevent vibration damage to the washing machine during transport (see previous
page). If you lost the angular pieces and the blocking rods, they can be
ordered from the manufacturer. After transport, the washing machine should be
left to stand still for at least two hours before it is connected to the power
mains, so that it can reach room temperature. The appliance should be
installed and connected by a trained technician. Carefully read the
instructions for use before connecting the washing machine. Repairs or
warranty claims resulting from the incorrect connection or use of the washing
machine shall not be covered by the warranty.
REQUIRED SPACE FOR INSTALLING
WARNING!
- Stability is important to prevent the product from moving across the installation site! Make sure to level the appliance and install it on a stable base in a longitudinal and traverse directions by screwing the adjustable feet up or down.
- Make sure the appliance is not standing on the power cord.
- Observe the minimum required clearances from the walls as indicated in the figure.
The room in which the appliance is placed must meet the following requirements:
- Dry, level and stable solid base
- Avoid direct sunlight
- Sufficient ventilation
- Room temperature of minimum 5°C and maximum 35°C
- Keep far away from heat sources such as coal, gas or wood-burning appliances.
WASHING MACHINE INSTALLATION CLEARANCES
The washing machine may not be in contact with a wall or adjacent furniture. For optimum washing machine operation, we recommend observing the clearances from the walls as indicated in the figure. In case of failure to observe the minimum required clearances, safe and correct washing machine operation cannot be ensured. Moreover, overheating can also occur (figures 1 and 2). Installing the washing machine under a countertop is not recommended.
LEVELLING THE APPLIANCE
Use a water level and spanners No. 32 (for feet) and 17 (for the nut).
- Level the washing machine in longitudinal and traverse direction by screwing the adjustable feet up or down.
- After adjusting the height of the feet, firmly tighten the jam nuts (counter nuts) using a spanner No 17, by turning them towards the bottom of the washing machine (see figure).
Incorrect levelling of the washing machine with the adjustable legs may cause
vibration, appliance moving across the room, and loud operation. Incorrect
levelling of the washing machine is not subject to warranty. Sometimes, an
unusual or louder noise may appear during appliance operation; these are
mostly the result of improper installation.
CONNECTING THE WATER SUPPLY HOSE
WARNING! To prevent leakage or water damage, follow the instructions in this
chapter. Make sure not to kink, crush or modify the water supply hose. Tighten
the water supply hose by hand, firmly enough for the hose to have a good seal.
After connecting the hose, the seal must be checked for any leaks. Do not use
pliers or similar tools when connecting the water supply hose as this could
damage the nut thread.
- Connect the water supply hose to the water inlet valve on the back of the appliance.
- Connect the other end of the water supply hose with the aqua stop to a water tap with cold water.
CONNECTING THE WATER DISCHARGE HOSE
WARNING!
- Make sure not to kink or stretch the water discharge hose.
- Connect the water discharge hose properly, otherwise it could result in damage or water leakage.
Feed the water discharge hose into a drain pipe, wash basin or floor drain. Be careful not to feed the water discharge hose too deep in the drain. Otherwise, the wastewater cannot flow freely. The vertical distance from the floor to the end of the discharge hose may be no more than 100 cm and no less than 60 cm.
- Put the water discharge hose in a floor drain.
- Connect the water discharge hose to a drain pipe
CONNECTING THE APPLIANCE TO THE POWER MAINS
WARNING!
- Before connecting the appliance to the power mains, wait at least 2 hours to allow the appliance to reach room temperature.
- Connect the appliance to an earthed power outlet. After installation, the wall outlet must be freely accessible. The outlet must be fitted with an earth contact (in compliance with the relevant regulations).
- Information about your appliance is shown on the rating plate
- Using an over-voltage protection to protect the appliance in case of a lightning strike, is recommended.
- Do not connect the appliance to the power mains using an extension cord.
- Do not connect the appliance to an electrical outlet intended for an electric shaver or hair dryer.
- Any repair and maintenance pertaining to safety or performance must be done by trained experts.
- A damaged power cord may only be replaced by a person authorized by the manufacturer.
BEFORE USING THE APPLIANCE FOR THE FIRST TIME
- Before washing, please make sure the appliance is properly installed.
- Your appliance was thoroughly checked before it left the factory. To remove any residual water and to neutralise potential odours, it is recommended to clean your appliance before first use. To do so, please run the Cotton programme at 90°C without laundry and detergent. See the chapter WASHING.
operation
BEFORE EACH WASHING
- The ambient temperature of the appliance should be 5-40°C. If used below 0°C, the inlet valve and draining system may be damaged. If the appliance is installed under freezing conditions, it should be transferred to an environment with a normal ambient temperature to ensure the water supply hose and water discharge hose can unfreeze before use.
- Before each washing, sort your laundry by reading the care labels and the detergent use instructions. Use non-foaming or less-foaming detergents suitable for machine washing.
WARNING!
- Do not wash clothes that have been cleaned, washed, soaked in or dabbed with combustible or explosive substances such as wax, oil, paint, gasoline, alcohol, kerosene or other flammable materials.
- Washing single items may easily create major eccentricity and cause vibrations and noise due to unbalance. Therefore it is suggested to add one or two more laundry items to the wash, so that spinning can be done smoothly.
PREPARING BEFORE WASHING
NOTE!
- Additional detergent needs to be added in compartment if the pre-wash function is selected.
WASHING
USING THE DISPENSER TRAY
A separator/divider tab is supplied with the washing machine, which allows
adding liquid detergent to the main wash compartment (left compartment).
- When using powder detergent, the separator/divider tab should be lifted.
- When using liquid detergent, the separator/divider tab should be lowered.
NOTE!
- Before adding hardened lumps of powder detergent or a thick stringy liquid detergent or additive into the dispenser tray, it can be diluted in some water before pouring it in, as it may otherwise clog the piping in the appliance and cause a water overflow.
- Choose a suitable type of detergent, suitable for the selected washing temperature and fabric, to get the maximum washing performance and a minimum of water and energy consumption.
- Add powder or liquid detergents according to the manufacturer’s instructions, considering the washing temperature, washing programme, how soiled the laundry is, and water hardness.
AFTER WASHING
When the program is finished and the appliance is ready, a buzzer will sound
and on the display [ End ] appears for a few seconds before the display goes
out.
CONTROL PANEL
THE WASHING PROCESS IN STEPS
- Read the labels on the laundry. Sort the laundry by type of fabric, colour, soiling and allowed washing temperature.
- Switch on the washing machine by pressing the On/off/reset button.
- Open the washing machine door. Load the washing machine and close the door.
- Choose the washing programme by rotating the selector knob to the left or to the right. See the PROGRAMME TABLE on the next page.
- Adjust settings and select additional functions on the touch display. See the WASHING MODE below for a description.
- Start the washing program by pressing the Start/Pause button.
PROGRAMME TABLE
Maximum load (MAX) ** Half load (1/2) / Any load (0 kg – MAX kg)
NOTE!
- Add powder or liquid detergents according to the manufacturer’s instructions, considering the washing temperature, washing program, how soiled the laundry is, and water hardness.
- The maximum amount of laundry in kg (for the cotton program) is indicated on the rating plate fitted under the washing machine door.
- Maximum or nominal load applies to laundry prepared pursuant to the IEC 60456 standard.
- For a better washing effect, we recommend loading the drum to 2/3 when using the cotton programs.
ADJUSTING THE SETTINGS
Most programs feature basic settings, but these settings can be changed.
Adjust the settings by pressing the relevant function button (before pressing
the Start/Pause button). Functions that cannot be changed with the selected
washing program are partly lit (dimmed). Certain settings cannot be selected
with some programs. Such settings will not be lit, and the button will flash
when pressed. Description of lighting of functions for the selected program:
- Lit (Basic/preset setting)
- Dimmed (Functions that can be adjusted)
- Unlit (Functions that cannot be selected)
WASHING MODE
NORMAL CARE (basic/default setting) No button lit.
INTENSIVE [intensief] (This mode will save energy; washing time will be
longer, and water consumption will be lower.)
SHORT [kort] (This mode will save time as programme duration will be shorter,
but it will use more water.)
- The light on the button for the selected washing mode is lit.
RPM [toeren] (SPINNING RATE/DRAIN/PUMP STOP)
For changing the spinning rate, only draining, and pump stop. With a preset or
selected spinning rate, the spinning rate number will light up on the display
unit. If you select draining without spinning, the symbol will appear on the
display unit. If you select Pump stop, the symbol will appear on the display
unit. Select the Pump stop option when you want the laundry to stay soaked in
the water from the last rinse cycle in order to prevent it from creasing when
you are unable to take it from the washing machine immediately after the
washing program is complete. You may set the desired spinning rate. To
continue the program, press the Start/Pause button that is lit. Water will be
drained (pumped out) and the final spin cycle will run.
CHILD LOCK (RPM [toeren] and Start Delay [startuitstel])
A safety feature. To activate the child lock, simultaneously press RPM
[toeren] and Start Delay [startuitstel] and hold them for at least three
seconds. The selection will be confirmed by an acoustic signal and by a signal
light (the symbol will be lit). Follow the same procedure to deactivate the
child lock. As long as the child lock is activated, programme, settings, or
additional functions cannot be changed. Child lock remains active even after
the washing machine is switched off. For safety reasons, the child lock does
not prevent switching off the washing machine with the On/Off/Reset button. To
select a new programme, the child lock must first be deactivated.
Start Delay [startuitstel]
Use this function to start the washing cycle after a certain amount of time
has elapsed. Press Start Delay [startuitstel] and -:– will appear on the
display. If, for example, you choose a programme with a duration of 2:39, the
time will be indicated on the display unit, and the symbol will be lit under
the time. If the function Start Delay has been selected, the symbol will be
lit. By pressing Start Delay [startuitstel], you can adjust the time in
30-minute steps up to 6 hours, and by 1-hour steps up to 24 hours.
If nothing is pressed for 5 seconds, the actual washing time will be
displayed. To set the time to the end of the washing programme again, press
Start Delay.
The function is activated when the Start/Pause button is pressed. The washing
machine will count down the set time. When the countdown reaches zero, the
selected washing programme will start automatically.
- To interrupt or change the start delay time, press and hold the On/Off/Reset button. Press Start Delay [startuitstel] to select a new delay time and confirm it by pressing the Start/Pause button.
- To quickly cancel the start delay, press and hold Start Delay [startuitstel] for 3 seconds. The washing program will resume.
- In case of a power supply failure before the delay time has elapsed, press the Start/Pause button to resume the delay time countdown.
EXTRA WATER [extra water] (HIGH WATER LEVEL)
Use this function to wash with a larger amount of water, and with two
additional rinse cycles on some programs.
Pre Wash [voorwas]
Washing heavily soiled laundry, particularly with stubborn superficial stains.
If you select Pre Wash [voorwas], add the detergent into the prewash
compartment.
- When the washing machine is switched off, all extra functions return to their basic or custom settings, except for the acoustic signal setting.
FUNCTION TABLE
PROGRAMME DURATION / TEMPERATURE / SPINNING RATE
Spinning rate can be changed, and the newly set rate can be up to the maximum rate Depending on the model Standard program.
- Low water temperature, low mains voltage and different washing loads may affect the washing time; the remaining time displayed is adjusted accordingly during the washing process.
- Due to deviations in terms of type and amount of laundry, spinning, power supply oscillation, and ambient temperature and humidity, the program duration and power consumption values measured at the end user may differ from the ones stated in the table.
Acoustic signal volume can be set at four levels
- 0 means the sound is off;
- 1 means that the button sound is activated;
- 2 means low volume, and
- 3 means high volume.
Choose the volume level by rotating the programme selector knob to the left or to the right. The lowest setting means that the acoustic signal is switched off.
maintenance and cleaning
WARNING!
Always unplug the appliance and close the water tap before cleaning and
maintenance.
CLEANING THE EXTERIOR OF THE APPLIANCE
Proper maintenance of the appliance can extend its useful life. Clean the
exterior of the appliance and the control panel using a soft damp cloth and
water. If necessary, a diluted non-abrasive neutral cleaning agent can be used
to clean the appliance.
CAUTION!
- Do not use abrasive or caustic agents, formic acids, diluted solvents or similar substances, such as alcohol or chemical products that could damage the appliance. Please observe the recommendations and warnings provided by the cleaning agent manufacturer.
- If there is any water overflow, use a cloth to wipe it off immediately.
- Do not clean the appliance with a jet of water.
- Do not use sharp items to clean the appliance.
CLEANING THE DRUM
Any rust stains left inside the drum by metal articles must be removed
immediately using chlorine-free detergents. Do not use steel wool for cleaning
the drum!
NOTE!
- Do not keep laundry near the appliance while cleaning the drum.
- When you often wash at 40°C or lower temperatures, or when you haven’t used the appliance for a longer period of time, clean the drum. Run the Cotton programme at 90°C without laundry. Preferably use a powder detergent.
CLEANING THE RUBBER DOOR GASKET AND THE GLASS
Wipe the glass and rubber door gasket after each wash to remove lint and
stains and to extend the useful life of the appliance. If lint builds up, it
can cause leakages. Check the rubber door gasket to remove any coins, buttons
or other objects after each wash. Clean the rubber door gasket and the glass
once a month to ensure normal operation of the appliance.
CLEANING THE INLET FILTER IN THE WATER TAP
NOTE!
- A diminishing water flow is a sign that the inlet filter needs to be cleaned.
- Cleaning the inlet filter every 3 months ensures the normal operation of the appliance.
- Close the water tap and remove the water supply hose.
- Clean the inlet filter with a brush under running water.
- Reconnect the water supply hose to the water tap.
CLEANING THE INLET FILTER AT THE BACK OF THE APPLIANCE
- Close the water tap.
- Unscrew the water supply hose from the back of the appliance.
- Pull out the filter with a long nose plier and clean the filter using a brush under running water.
- Reinstall the filter to the water inlet and reconnect the water supply hose.
- Open the water tap.
CLEANING THE DISPENSER TRAY
- Press the small tab and pull the dispenser tray out of the recess.
- Clean the dispenser tray under running water using a brush, and dry it. Also, remove any detergent residue from the bottom of the housing. Make sure not to forget to clean the drain hole of the softener compartment and the openings at the bottom of the dispenser tray.
- Clean the inside of the recess with a brush.
- If required, remove and clean the plug cap.
- Clean the plug cap under running water and replace it.
- Push the dispenser tray back in the recess.
NOTE
- Do not use abrasive or caustic agents to clean plastic parts.
- Cleaning the dispenser tray every 3 months ensures normal operation of the appliance.
CLEANING THE DRAIN PUMP FILTER
The pump filter can filter the yarns and small foreign matters from the
washing. Especially after washing fleecy, woolly or very old laundry. Clean
the pump filter and the in-wall water trap whenever the symbol appears on the
display unit.
WARNING!
- Unplug the appliance to avoid electrical shock before cleaning.
- Be careful of hot water!
- Allow detergent solution to cool down.
- During cleaning, some water may be spilled. It is recommended to place an absorbent cloth on the floor.
- Open the pump filter cap using a suitable tool (flat screwdriver or a similar tool).
- Pull out the water outlet funnel before cleaning the pump filter. Rotate the pump filter slowly in the counter clockwise direction. Pull out and remove the pump filter to allow the water to drain slowly.
- Clean the pump filter thoroughly under running water.
- Remove all and any objects and impurities from the filter housing and the pump propeller. Replace the pump filter as shown in the figure and fasten it by rotating in the clockwise direction. For a good seal, the filter gasket surface should be clean.
WARNING!
- Never remove the pump filter cap during a washing cycle. Always wait until the appliance has finished the cycle and is empty.
- When the appliance is in use and depending on the selected programme, there can be hot water in the pump.
- When replacing the pump filter cap, ensure it is securely snapped in place.
troubleshooting
The washing machine will automatically control the operation of particular functions during the washing cycle. If any irregularity occurs, this will be identified by a message (E: XX) on the display. The appliance will report the error until it is switched off. External disturbances (e.g. the power grid) may result in various error reports. In such cases:
- Switch off the appliance and wait for a few seconds.
- Switch the appliance on and repeat the washing programme.
- Most errors during operation can be solved by the user.
- If the error persists, call the customer care service.
- Repairs may only be carried out by an adequately trained person.
- Repairs or warranty claims resulting from incorrect connection or use of the appliance shall not be covered by the warranty. In such cases, the costs of repair shall be charged to the user.
- The warranty does not cover the errors or failures resulting from external disturbances (lighting strike, power grid failures, natural disasters etc.).
TROUBLESHOOTING AND ERROR TABLE
- Unevenly distributed laundry or lumps of laundry in the washing machine drum can cause problems such as vibration and noisy operation.
- The washing machine detects such problems and the UKS (stability control system) will be activated.
- Smaller loads (e.g. one towel, one sweater, one bathrobe etc.) or clothes made of materials with special geometrical properties are virtually impossible to distribute evenly across the washing machine drum (slippers, large items etc.). This results in several attempts to redistribute the laundry, which in turn leads to longer programme duration. In extreme cases of unfavourable conditions, the programme can be completed without the spinning cycle.
- The UKS (stability control system) allows stable operation and a longer useful life of the washing machine.
If the problems persist despite observing the advice above, call an authorised service technician. Repairs or warranty claims resulting from incorrect connection or use of the washing machine shall not be covered by the warranty. In this case, the user will cover the cost of repair.
CUSTOMER SERVICE
WARNING! Risk of electric shock
- Never try to repair an appliance which is defective or presumed to be defective. You may put your own and future users’ lives in danger. Only authorised specialists are allowed to carry out this repair work.
- Improper repair will void the warranty and subsequent damages cannot be recognized!
TRANSPORT
IMPORTANT STEPS WHEN MOVING THE APPLIANCE
- Unplug the appliance and close the water tap.
- Check that the door and dispenser tray are closed properly.
- Remove the water supply hose and the water discharge hose from the house installations.
- Allow the water to drain completely from the appliance.
- IMPORTANT: Re-install the transport bolts in the back of the appliance.
- The appliance is heavy. Transport with care. Never hold any protruding part of the appliance when lifting. The door o the appliance cannot be used as a handle.
technical specifications
- Model VWM9001W
- Washing capacity 9.0 kg
- Power supply 220-240V~, 50Hz
- Rated power 2000 W
- Max. current 10 A
- Standard water pressure 0.05 – 0.8 MPa
- Dimension (WxDxH in cm) 60 x 54.5 x 85
- Nett weight 67 kg
RECYCLING
This symbol means that this product should not be disposed of with regular
household waste (2012/19/EU). Observe the rules that apply in your country for
the separate collection of electric and electronic products. Correct disposal
of the product prevents negative consequences for the environment and for
public health. The packaging material of this product can be recycled 100%,
return the packaging material separately.
PRODUCT INFORMATION SHEET ACC. REGULATION (EU) 2019/2023
Inventum Huishoudelijke
Apparaten B.V.
Postbus 5023
6802 EA Arnhem
www.inventum.eu
instagram.com/inventum1908
facebook.com/inventum1908
youtube.com/inventum1908
VWM9001W/01.1121
References
- Inventum Huishoudelijke Apparaten - Altijd 5 jaar garantie!
- Inventum Huishoudelijke Apparaten - Altijd 5 jaar garantie!
- Duurzame oplossingen voor bestaande bouw en nieuwbouw
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>