Canac 66001825 Stud Detector 3 in 1 User Guide

May 15, 2024
Canac

GUIDE D’UTILISATION
USER GUIDE

66001825 Stud Detector 3 in 1

  1. LCD display
  2. ON/OFF button
  3. Mode selector button

After 1 minute of non-use, the tester will automatically switch off to save batteries.
POWER SUPPLY
The tool requires one 9 V battery to operate.
BATTERY INSTALLATION

  1. Open battery cover on back of case.
  2. Insert battery into case and replace battery cover.

USER INSTRUCTIONS

Turning the power on/off:
On: Press the ON OFF button once.
Off: Press the ON OFF button again.
Mode selection:
Press the mode selector button to display and select the mode. You should hear a “bleep” each time you press the button. Stud scan and deep scan modes:

  • Use stud scan mode for depths to about ¾” (18 mm).
  • Use deep scan mode for depths to about 1 ¼” (32 mm).
  • Position the scanner flat against the wall. Select the mode. Press and hold the scan button until the beeper beeps.

Slowly slide the device horizontally across the wall, left to right.
When full bars appears on the LCD and a steady tone sounds, you have located the edge of the stud. Mark this spot.
Continue pressing the ON OFF button in and scan beyond the marked spot until the bars disappear. Without releasing the scan button, slide the scanner in the opposite direction to locate the other edge of the stud. Mark this second spot. The middle of the stud is centered between the two marks. Calibrating and scanning in metal scan mode
Select metal mode. Hold the scanner away from any metal objects. Press and hold the scan button until the beeper sounds. Place the scanner flat on the surface. While holding in the scan button, slowly move the scanner randomly until the LCD screen indicates proximity to metal, with the center bar indicating the closest proximity. Mark this spot.
Continue scanning beyond the marked spot to detect the width of the metal object. If it is wide, move the scanner in the opposite direction to locate and mark the other edge. Avoid sawing or drilling between the two marks. Widths will vary from a single peak for narrow rebar to a wide area for metal studs, I-beams, junction boxes, etc. Scanning in AC mode
Detects AC at depths to about 2″ (50 mm).
Select AC scan mode to locate hot wires. Begin by holding the scanner at a distance from known hot wiring.
Hold in the scan button and slowly slide the scanner across the wall.
The AC indicator will appear on the screen if a hot wire is nearby (the more bars on the screen, the closer the hot wire). Mark this spot.
The scanner detects from 90V to 250 V at 50 to 60 Hz AC in a hot electrical wire. For safety reasons, the voltage detection feature works continuously in all modes.

ONE-YEAR LIMITED WARRANTY

NOVELCA offers a limited warranty for this product (hereafter: the “Product”) for one (1) year from the date of purchase of this Product, with the conditions set out below.
This limited warranty is valid only for the original purchaser of the Product and it may not be transferred.
The present limited warranty is not meant to exclude, restrict, limit or modify the legal warranty given by law to the purchaser of the Product.
If the Product contains a manufacturing defect or if one or more parts of the Product is defective, the retailer commits to replace or repair, at its sole discretion, the defective part or parts without charge under the following cumulative conditions: 1) the purchaser must contact the retail store where the Product was purchased; 2) the purchaser must return the defective part or parts or the Product to the retailer; 3) the purchaser must provide the retailer the invoice as proof of purchase and date of purchase of the Product; 4) the purchaser must supply the Product identification information, including the serial number or the model number; and 5) the period of one (1) year covered by this limited warranty must not be expired. If the retailer decides to replace the defective part or parts, the replacement part or parts would be new or reconditioned, equivalent to new parts. The present limited warranty does not create any other obligation with the provider of the guarantee than those explicitly described above.
This limited warranty is not applicable: 1) to consumable parts; 2) to normal wear; 3) when the Product is used for other purposes than what is described in the user guide (if any); 4) when the serial number or other identification information of the Product is erased or withdrawn; 5) to damages that are only aesthetic and do not affect the normal use of the Product; 6) when the damages, defects, faults or other problems arise from: a) an inadequate maintenance of the Product; b) a faulty installation or assembly of the Product or an installation or assembly that is not in accordance with the user or installation guide (if one is provided); c) a modification, a repair or dismantling of the Product by a person not authorized by the retailer or the manufacturer; d) the transportation by the purchaser, his employee, officer or representative; e) a negligence by the purchaser, his employee, officer or representative; f) an accident; g) a case of force majeure or any event that is not caused by the Product itself.
FRENCH VERSION VS ENGLISH VERSION
In case of discrepancy between the French and the English versions of the text of this limited warranty, the French version shall prevail.

NOVELCA
Canada G2J 1C8

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals