PowerLocus Boom Wireless Headphone User Manual
- June 6, 2024
- PowerLocus
Table of Contents
PowerLocus Boom Wireless Headphone
Product Usage Instructions
- 3.5mm AUX Mode:
- Simply plug the 3.5mm audio cable into the aux port to listen in wired mode. Note that buttons and microphones will be inactive in this mode.
- Power On/Off and Call Functions:
- To power on, press the multi-function key for 2 seconds until the LED indicator lights up blue. To power off, press the multi-function key for 5 seconds. Use the buttons for call functions and music control as indicated in the manual.
- Charging:
- Connect the Type-C plug of the charging cable to the headphone jack (USB) on the Type-C port into a 5V power outlet.
- The headphone indicator will be red when charging and will turn blue when fully charged.
- Pairing:
- When turned on, the headphone automatically enters Bluetooth pairing mode with alternating red and blue lights flashing. Enable Bluetooth on your device and select “PowerLocus Boom” to pair. The blue light indicates a successful connection.
- EQ Mode Features:
- To select the audio mode (Pop, Bass, Rock, Vocal), click the EQ mode key after turning on the headphones.
FAQs
- How can I switch between audio modes?
- To switch between audio modes (Pop, Bass, Rock, Vocal), simply click the EQ mode key after turning on the headphones.
- How do I know when the headphone is fully charged?
- The headphone indicator light will turn blue when the headphone is fully charged.
Packing accessories
Specifications
- Support profile: HFP/HSP/A2DP/AVRCP
- Speaker Size: 40mm
- Impedance: 32 Ohm
- Sensitivity: 97dB +/-3dB
- Frequency Response: 20Hz-20kHz
- Bluetooth version: 5.3
- Transmission range: 10m
- Built-in rechargeable battery: 500mAh
- Input 5V 1A
- Maximum transmission power: 8dBm
- Stand By Time: 150 hours
- Music Play Time: 60 hours
- Charging Time: 2 hours
Key instruction
- EQ mode key
- Microphone
- USB Type-C charging port
- 3.5mm audio port
- LED indicator
- Multifunction button
- Volume down/previous song
- Volume up/next song
On/Off
- Power on: Long press the ⑥ multi-function key for 2 seconds, the LED indicator will light up blue and the headphones will enter the Bluetooth pairing mode.
- Power off: Long press the multi-function key for 5 seconds, and then the LED indicator will turn red and then turn off.
Pairing：
- When the headphone is turned on, the headphone enters the Bluetooth pairing mode automatically, and the RED and BLUE lights flash alternately.
- Enable the Bluetooth function, to select “PowerLocus Boom” in the device list. After the connection is successful, the BLUE light is on
EQ mode features
- After the headphone is turned on, click the ① EQ mode key to select the audio mode you wish. Choose between Pop, Bass, Rock and Vocal mode.
Factory data reset
- Press and hold the ⑧ “+” and ⑦ “-” buttons for 5 seconds at the same time, the headphones will separate the Bluetooth connection and restore factory settings.
- You have to activate the Bluetooth function of your phone again and then find and select the “PowerLocus Boom ” from the device list for pairing.
3.5mm AUX mode:
- Simply plug the 3.5mm audio cable into the ④ aux port to listen to wired mode. Please note that once the cable is connected, the buttons of the headphones and its microphone will not be active
INSTRUCTIONS FOR
Charge
- Connect the Type-C plug of the charging cable to the headphone jack(USB) on the Type-C port into the 5V power outlet.(Note: No power adapter).
- The headphone indicator is red, it means that the headphones has stared and is being charged. When the headphone is fully charged the indicator light will turn blue.
- Q1: What if the headset cannot be paired with a mobile device?
- Please press the “+” and “-” volume key and press 5S to restore the factory setting. Reboot and reconnect the device to Bluetooth.
- Q2: What if the headphone cannot be charged?
- Check whether the TYPE-C interface has foreign matter and whether the charger is a high-power fast charger. Replace the headphone accessories with your own cable for charging.
- Q3: Lag appears in connecting to music, and the Bluetooth connection encounters intermittent phenomenon.
- The distance of normal headphones is 10 meters ~15 meters as the straight line. When lag appears, immediately check whether the
- Bluetooth version of the device is low and there are large signal interference devices around, and reconnect in another scene.
FCC
Warning
This device complies with Part 15 of the FCC Rules.
Operation is subject to the following two conditions:
- this device may not cause harmful interference, and
- this device must accept any interference received, including interference that may cause undesired operation.
by the party responsible for compliance could void the user’s authority to operate the equipment.
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, under Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used by the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and the receiver
- Connect the equipment to an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help
NOTE: This device and its antenna(s) must not be co-located or operated in conjunction with any other antenna or transmitter. The device has been evaluated to meet general RF exposure requirements.
ISED Canada Statement:
This device contains licence-exempt transmitter(s)/receiver(s) that comply with Innovation, Science and Economic Development Canada’s licence-exempt RSS(s).
Operation is subject to the following two conditions:
- this device may not cause interference and
- this device must accept any interference, including interference that may cause undesired operation of the device.
Radiation Exposure: This equipment complies with Canada’s radiation Exposure limits set forth for an uncontrolled environment to maintain compliance with IC’s RF Exposure guidelines. This equipment should be installed and operated with a minimum distance of 0mm the radiator of your body. This device and its antenna(s) must not be colocated or operation in conjunction with any other antenna or transmitter.
Safety instructions
- Please charge the headphones before first use.
- Please charge at least once every 3 months to keep the battery in good condition
- To protect your hearing, please do not use the headphones long time with too high a volume
- Do NOT expose the headphones to hot temperature
- Protect from shocks and drops
- Do NOT try to open the product
- Do NOT expose to moisture, rain and liquids.
CONTACT
Customer
- Service: info@powerlocus.com.
- Manufacturer: GL GRUP 2015 LTD
- Vasil Levski 36 Str.
- Dryanovo 5370
- Bulgaria
- GL GRUP 2015 LTD Unit J, Hove Technology Centre, Hove BN3 7ES, United Kingdom
- GL GRUP 2015 LTD
- Vasil Levski 36 Str.
- Dryanovo 5370
- Bulgaria
Hereby GL Grup-2015 LTD declares that wireless headphone PowerLocus Boom complies with essential requirements and other relevant conditions of Directive 2014/53/EU. The full text of the EU declaration conformity is available at the following internet address: (powerlocus.com/doc)
- Frequency: 2402 -2480 MHz
- Max radio frequency power: 100 mW (EIRP) GL GRUP-2015 LTD. 36 VASIL LEVSKI STREET, 5370 DRYANOVO, BULGARIA
- To find out more about the UK Declaration of Conformity, please visit https://powerlocus.com/doc-uk-boom.
This symbol on a product means that the product is covered by European Directive 2012/19/EU. Electrical products should not be disposed of with household waste. Please recycle them at the collect points provided for this purpose. Contact the local authorities or your dealer for recycling advice. Proper disposal of old appliances helps preserve the environment and health
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>