PowerLocus P19 Bluetooth Over Ear Headphone User Manual

PowerLocus P19 Bluetooth Over-Ear Headphone

Product Information

Product Usage Instructions

Product Function Instructions:

• + button: Volume up/Next song
• o button: MFB button
• – button: Volume down/Previous song
• Bluetooth indicator
• Power On/Off & EQ button
• 3.5mm audio port
• USB Type C charging port
• Microphone

Product Operation Instructions:

To perform the following actions, refer to the Bluetooth indicator:

• Connected: The blue indicator blinks every 6 seconds.
• Pairing mode: The red and blue indicators blink alternately.
• Reset: The red and blue indicators blink alternately.
• Music Mode: The blue indicator blinks every 6 seconds.
• Full Charging: The indicator will be solid red.
• Charging Mode: The indicator will be solid blue.
• Power off: The red indicator will go off.

AUX Mode:

To use the AUX mode, follow these steps:

1. Connect one end of the 3.5mm audio cable into the audio jack of the headset.
2. Connect the other end into your mobile or other devices.

Note : The headphone will power off once the 3.5mm audio cable is plugged into the audio jack while the headphone is powered on. If you want to turn on the headphone, the 3.5mm audio cable must be taken out from the headphone.

Charging Instruction:

Before using, please check and ensure the battery has enough charge.
While the headphone is in low battery, use the Type-C charging cable to charge. The charging indicator will be RED when charging. Once it is fully charged, the indicator will be solid BLUE.

FAQ:

For any warranty or problems with the product, please contact us at [email protected].

For Warranty or Problems with the product, please contact us!
Support Email : [email protected]

PRODUCT FUNCTION INSTRUCTIONS

1. “+”: Volume up/Next song
2. “o”: MFB button
3. “-”: Volume down/Previous song
4. Bluetooth indicator
5. Power On/Off & EQ button
6. 3.5mm audio port
7. USB Type C charging port
8. Microphone

FEATURES

• Bluetooth Version: V5.3
• Working Distance Range: 10M
• Frequency Range: 20Hz-20kHz
• Audio Drivers: 40mm Charging Voltage: DC 5V
• Charging Time: About 1.5 Hours
• Talking/Music Time: About 20 Hours (50% Volume)
• Impedance: 32 Ohms Weight: 175g/0.39LBs
• Volume Sensitivity: 100+/-3dB
• Bluetooth Specication Power Class 1
• Frequency band: 2.402-2.480GHz
• Operating frequency: 2402-2480MHz
• Rated power consumption: 120 mW
• Maximum output power: < 7dBm
• Operating Temperature: 0 °C to 45 °C

PRODUCT OPERATION INSTRUCTIONS

Power on/off

• How to turn it on?: In power-off status, press and hold the power on button 2s-3s, the blue light will be on around 2 seconds, then blue and red light will blink alternately, the headphone enters into pairing mode.
• How to turn it off?: In power-on status, press and hold the power off button 3s, the indicator light will goes off then.

Pairing
When the headphone is turned on and the LED is Blue/Red, open the Bluetooth menu of your device (Phone, Tablet, PC etc.) and select the appearing “PowerLocus P19”. Once paired successfully, the blue indicator blinks every 6 seconds

EQ mode
Totally three kinds of EQ for option:
Bass mode; 2) Pop mode; 3) Vocal mode Click the EQ button to switch EQ

Music playing

• Volume up: Click the “+” button to increase volume
• Volume down: Click the “-” button to decrease volume
• Next song: Press and hold the “+” button around 2 seconds
• Previous song: Press and hold the “-” button for around 2 seconds
• Music play/pause: Click the MFB button

Calling (Mobile)

• Answer call: Click the MFB button when the call is incoming
• End call: Click the MFB button when the call is over
• Cancel call: Click the MFB button when calling
• Reject call: Press and hold the MFB button for around 2 seconds when a call is incoming
• Redial: Double-click the MFB button to redial the last call number

Bluetooth Reset:
Press and hold the “+” and ”-” buttons at the same time around 3 seconds until the red and blue indicator blink alternately. This way, you will reset the headphones and enter it into initial pairing mode again.

Voice assistant activation:
In standby mode or music mode, long press the MFB button 2 seconds to activate Siri or Google Assistant

BLUETOOTH INDICATOR INSTRUCTION

AUX MODE

Connect one end of the 3.5mm audio cable to the audio jack of the headset and the other end to your mobile or other devices.
Note : The headphone will be powered off once plug the 3.5mm audio cable into the audio jack (When the headphone is powered on). If you want to turn on the headphones, the 3.5mm audio cable must be taken out from the headphones.

CHARGING INSTRUCTION

Before using, please check and ensure the battery is enough While the headphones is in low battery, please use a Type-C charging cable to charge and the charging indicator will be RED when charging. Once it’s fully charged,the indicator will be solid BLUE

FAQ

Headphones can’t be turned on
Please ensure the battery is enough.

Pairing failure
Please ensure the headphone is in power on and pairing status, and the mobile or other device is located within 1 m range, And then redo again.

Connect automatically
The headphones will automatically connect the mobile or other devices used last time

The sound cut off/stuck
Check whether the mobile or other devices locate valid range (10m) and whether there are obstacles between the headphone and the mobile.

Charging way
Please ensure the charging adaptor is DC 5V/1A,or Car charger or power bank to charge the headphones.

CE

• Hereby GL Grup-2015 LTD declares that wireless headphone PowerLocus P19 complies with essential requirements and other relevant conditions of Directive 2014/53/EU.
• The full text of the EU declaration conformity is available at the following internet address: (powerlocus.com/doc)
• Frequency: 2402-2480 MHz
• Max radio frequency power: 100 mW (EIRP) GL GRUP-2015 LTD. 36 VASIL LEVSKI STREET, 5370 DRYANOVO, BULGARIA

WARNING:

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
NOTE : This equipment has been tested and found to comply with the limits for a Class B digital device, under Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used by the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful interference to radio or television reception which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and the receiver
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help

NOTE : This device and its antenna(s) must not be co-located or operated in conjunction with any other antenna or transmitter.
The device has been evaluated to meet general RF exposure requirements.

ISED CANADA STATEMENT:

• This device contains licence-exempt transmitter(s)/receiver(s) that comply with Innovation, Science, and Economic Development Canada ‘s license-exempt RSS(s). Operation is subject to the following two conditions: this device may not cause interference and this device must accept any interference, including interference that may cause undesired operation of the device.
• Radiation Exposure: This equipment complies with Canada’s radiation exposure limits set forth for an uncontrolled environment to maintain compliance with IC’s RF Exposure guidelines. This equipment should be installed and operated with a minimum distance of 0mm the radiator your body. This device and its antenna(s) must not be co-located or operate in conjunction with any other antenna or transmitter

DISPOSAL

This symbol on a product means that the product is covered by European Directive 2012/19/EU. Electrical products should not be disposed of with household waste. Please recycle them at the collection points provided for this purpose. Contact the local authorities or your dealer for recycling advice. Proper disposal of old appliances helps preserve the environment and health

Safety Instructions

1. Please charge the headphones before first use.
2. Please charge at least once every 3 months to keep battery in good condition.
3. To protect your hearing, please do not use the headphones long time with too high volume.
4. Do NOT expose the headphone to hot temperature
5. Protect from shocks and drops
6. Do NOT try to open the product
7. Do NOT expose to moisture, rain and liquids

To find out more about the UK Declaration of Conformity, please visit: https://powerlocus.com/doc-uk-p19

References

• PowerLocus Doc - PowerLocus

Read User Manual Online (PDF format)

Download This Manual (PDF format)

Download this manual  >>