PowerLocus P1 Bluetooth Headphones Over Ear User Manual
- June 14, 2024
- PowerLocus
Table of Contents
USER MANUAL PowerLocus
P1
Email Support: info@powerlocus.com
PRODUCT OVERVIEW
- Multi-function button
- ”-” button
- “+” button
- FM/MP3/Bluetooth mode switch button
- Call button
- Micro-SD card slot
- USB-C Charging Port
- Bluetooth connection status indicator
- 3.5mm AUX jack
- Microphone
Bluetooth Version: V5.3
Working Distance Range: 10M
Frequency Range: 20Hz-20kHz
Audio Drivers: Φ40mm
Charging Voltage: DC 5V
Charging Time: About 1.5 Hours
Talking/Music Time: About 20 Hours (50% Volume)
Impedance: 32 Ohms
Weight: 175g/0.39LBs
POWER ON/OFF
-
Power on: Press and hold the Power Button about 2 seconds until you hear a voice prompt of Power On” and “Pairing”, then release. The LED Indicator will flash blue and red alternately.
-
Power off
Option1 : Press and hold the Power Button about 2 seconds until you hear avoice prompt of “Power Off”, then release. The LED Indicator will be off. -
Option 2: tf the headset is not connected with any device within 10 minutes, it will be powered off automatically.
CONNECT WITH A MOBILE DEVICE
WIRELESS CONNECTION CONNECT WITH A MOBILE DEVICE
Stepl:
After turning the headset on, wait until you see the LED Indicator flash red
and blue alternately, which indicates the headset is ready to be paired to the
mobile device.
Step 2: Turn on the Bluetooth on your device, then search and connect to
the already appearing PowerLocus
Step3: There will be a voice prompt of “Connected” and the LED Indicator
will flash blue slowly if there is a music playing and be steady blue light if
no music is played.
Tips: Please connect the headset with your mobile device within 10
minutes.
DOISCONNECT
Go to the Bluetocth list of your mobile device, then select PowerLocus P1 and
disconnect the headset. You will hear a voice prompt of “Disconnected”.
WIRED CONNECTION
Step1 : Connect one end of the 3.5mm Audio Cable into the Audio Jack of
the headset.
Step2: Connect the other end into your mobile device.
Tips: The microphone only works with wireless connec tion.
When listening to music using the provided 3.5mm audio cable, the volume
adjustment and song switching functions can only be operated bythe mobile
device
FUNCTION OVERVIEW
MUSIC:
- Play/pause music: short press “multi-function” button
- Next song: long press “+” button
- Previous song: long press “-”button
- Volume up: short press “+” button
- Volume down: short press “-” button
Tips:
For Android device, if you have adjusted the volume by the headset to the
maximum level, but still feels it is too low, please turn up the volume
onyour mobile device as well.
When using the 3.5mm audio cable provided to listen to music, the functions of
volume adjustment and song switching can only be operated by the mobile
device.
CALLS:
- Redial: double-click the call button to redial the last call number
- Answer the call: Click the call button when call is coming
- End the call: click the call button to end the call
- Reject the call: long press the call button to reject the call
ACTIVATE SIRI/GOOGLE ASSISTANT:
Long press the call button to wake up Siri
CHARGE
Please charge the headset with the USB cable provided before your first
use.
Step 1: Connect one end of the USB cable into the micro USB port On the
headset.
Step 2: Directly connect the other end into a USB wall outlet; Or
connect the other end to a compatible adapter (not included), then plug it
into a socket. While Charging: Solid red will be showing up Fully Charged: Red
light will disappear
Tips: Please charge the headset when it’s turned off, It may take around
3 hours to reach a full charge. When the battery of the headset gets iow, the
LED Indicator will flash red and you will hear “Low Battery® frorn the
headset. Please charge it timely.
FM/MP3 MODE
- In powered-on mode, click the FM/MP3 button to activate the FM Radio mode;
- In FM mode,click the multi-function button, it will initiate searching for all radio stations automatically. Please await 40-50 seconds for all the stations to be memorized. After searching is over, you can change the FM stations with long pressing + and .
- Click the FM/MP3 button again, to go back to bluetooth mode.
- In power-on mode,will enter SD card mode if insert micro-SD card.
ABOUT CHARGING
- Do not turn on the headphone and don’t use bluetooth while charging.
- If the headphone is not used for a long time, the rechargeable battery may not be able to retain enough power. After repeated charge and discharge several times, the battery will be able to maintain the appropriate power
- If you store the unit for an extended period of time, charge the battery every six months to prevent over-discharge.
HOW TO RESET THE HEADPHONES?
Hold both Buttons for 4-7 seconds in order to reset the bluetooth and enter
pairing regime again.
CE
Hereby GL Grup-2015 LTD declares that wireless headphone PowerLocus P1 is in
compliance with essential requirements and other relevant conditions of
Directive 2014/53/EU. The full text of the EU declaration conformity is
available at the following internet address:
(powerlocus.com/doc)
Frequency: 2402-2480 MHz
Max radio frequency power: 100 mW (EIRP) GL GRUP-2015 LTD.
36 VASIL LEVSKI STREET, 5370 DRYANOVO, BULGARIA
Warning:
This device complies with Part 15 of the FCC Rules. Operation is subject to
the following two conditions: (1) this device may not cause harmful
interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation.
Changes or modifications not expressly approved by the party responsible for
compliance could void the user’s authority to operate the equipment.
NOTE: This equipment has been tested and found to comply with the limits
for a Class B digital device, pursuant to Part 15 of the FCC Rules. These
limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates, uses and
can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio
communications.
However, there is no guarantee that interference will not occur in a
particular installation.
If this equipment does cause harmful interference to radio or television
reception which can be determined by turning the equipment off and on, the
user is encouraged to try to correct the interference by one or more of the
following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help
NOTE: This device and its antenna(s) must not be co-located or operation
in conjunction with any other antenna or transmitter. The device has been
evaluated to meet general
RF exposure requirement.
ISED Canada Statement:
This device contains licence-exempt transmitter(s)/receiver(s) that comply
with Innovation, Science and Economic Development Canada ‘s licence exempt
RSS(s). Operation is subject to the following two conditions: this device may
not cause interference and
this device must accept any interference, including interference that may
cause undesired operation of the device.
Radiation Exposure: This equipment complies with Canada radiation
Exposure limits set forth for an uncontrolled environment to maintain
compliance with IC’s RF Exposure guidelines. This equipment should be
installed and operated with minimum distance of 0mm the radiator your body.
This device and its antenna(s) must not be co-located or operation in
conjunction with any other antenna or transmitter.
UK
To find out more about the UK Declaration of Conformity, pleasevisit:
https://oowerlocus.com/doc-uk-p1
**** This symbol on a product means that the product is covered by European
Directive 2012/19/EU.
Electrical products should not be disposed of with household waste. Please
recycle them at the collect points provided for this purpose. Contact the
local authorities or your dealer for recycling advice. Proper disposal of old
appliances helps preserve the environment and health
Safety Instructions
- Please charge the headphones before first time using.
- Please charge at least once every 4 months to keep battery in good condition.
- To protect your hearing, please do not use the headphones long tim with too high volume.
- Do NOT expose the headphone tc hot temperature
- Protect from shocks and drops
- Do NOT try to open the product
- Do NOT expose to moisture, rain and liquids
Made in China
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>