ADLER EUROPE 7913 Ventilator Fan User Manual

ADLER EUROPE 7913 Ventilator Fan

SAFETY CONDITIONS IMPORTANT INSTRUCTIONS ON SAFETY OF USE

The warranty conditions are different if the device is used for commercial purposes.

1.  Before using the product please read carefully and always comply with the following instructions. The manufacturer is not responsible for any damages due to any misuse.
2.  The product is only to be used indoors. Do not use the product for any purpose that is not compatible with its application.
3.  The applicable voltage is 220-240V,~50/60Hz. For safety reasons, it is not appropriate to connect multiple devices to one power outlet.
4.  Please be cautious when using children. Do not let the children to play with the product. Do not let children or people who do not know the device to use it without supervision.
5.  WARNING: This device may be used by children over 8 years of age and persons with reduced physical, sensory or mental capabilities, or persons without experience or knowledge of the device, only under the supervision of a person responsible for their safety, or if they were instructed on the safe use of the device and are aware of the dangers associated with its operation. Children should not play with the device. Cleaning and maintenance of the device should not be carried out by children, unless they are over 8 years of age and these activities are carried out under supervision.
6.  After you are finished using the product always remember to gently remove the plug from the power outlet holding the outlet with your hand. Never pull the power cable!!!
7.  Never leave the product connected to the power source without supervision. Even when use is interrupted for a short time, turn it off from the network, unplug the power.
8.  Never put the power cable, the plug or the whole device into the water . Never expose the product to the atmospheric conditions such as direct sun light or rain, etc.. Never use the product in humid conditions.
9.  Periodically check the power cable condition. If the power cable is damaged the product should be turned to a professional service location to be replaced in order to avoid hazardous situations.
10.  Never use the product with a damaged power cable or if it was dropped or damaged in any other way or if it does not work properly. Do not try to repair the defected product yourself because it can lead to electric shock. Always turn the damaged device to a professional service location in order to repair it. All the repairs can be done only by authorized service professionals. The repair that was done incorrectly can cause hazardous situations for the user.
11.  Never put the product on or close to the hot or warm surfaces or the kitchen appliances like the electric oven or gas burner.
12.  Never use the product close to combustibles.
13.  Do not let cord hang over edge of counter.
14.  Do not immerse the motor unit in water.
15. Do not insert fingers or any other objects in the housing grille of the device.
16.  Do not block the outlet.
17.  When done, prior to putting it away, drain water from the device.
18.  If the device is not used for a long time, unplug it from the power source.
19.  Always use new batteries to replace the drained batteries in the remote control.
20.  Do not move the device when the inner tank is filled with water .
21.  Do not place any objects on the device.
22.  The device can be used only with properly working ventilation.
23.  To provide additional protection, it is advisable to install a residual current device (RCD) in the electric circuit with a rated residual current not exceeding 30mA. Ask an electrician for this.

WARNING.

1.  It should be remembered that a high level of humidity may favor the development of biological organisms in the environment.
2.  Do not get wet the device or wet the area around the device. If moisture appears, reduce the ef ficiency of the humidifying function.
3.  Do not allow absorbent materials such as carpets, curtains, tablecloths to get wet.
4.  Never leave water in the tank when the device is not in use.
5.  During filling and cleaning, disconnect the device from the mains.
6.  Clean the device and water tank before using it again.

WARNING: When the water is not replaced and the tank is not properly cleaned every 3 days, microorganisms that may be present in the water or in the environment where the device is used or stored may develop in the water tank and be blown out to the surroundings. This can cause a very serious health risk.
WARNING: Every three days, empty the water tank and top up with clean water . Before refilling, clean the tank with fresh tap water or using detergents. Removes any scale, deposits or film that has formed on the sides of the tank and on the interior surfaces. After washing, wipe all surfaces dry.\

DESCALING

1.  Perform the descaling procedure in accordance with the instructions of the descaling agent specified by the manufacturer .
2.  Use descaling agents intended for this purpose.
3.  Carry out the descaling procedure at least every 3 months.
4.  Descaling only the water tank with the device turned of

DEVICE DESCRIPTION

1. Cover of topwater tank
2.  Topwater tank
3.  Bobbin winder bracket
4.  Handle
5.  Internal filter
6.  Water level indicator
7.  Water inlet with stopper
8.  Drain plug
9.  Wheels
10.  Water tank 12 liters
11.  Two containers for water freezing

USING THE APPLIANCE

A noticeable reduction in the temperature of the outlet air occurs after putting into the top water (2) tank one or both plastic containers (11) attached to the product. Plastic containers (11) should be previously filled with water in ¾ high and frozen in the freezer. It is recommended to fill the tank (10) with cold tap water.

1.  After unpacking the device from the packaging, mount the wheels and set the air cooler on a dry, flat surface, then connect the power plug.
2.  Open the cover of top water tank (1) and pour in the water to water inlet with stopper (7). Be careful not to exceed the maximum level on water level indicator (6).
3.  Turn on the device with the “LOW”, “MID” or “HIGH” button on the control panel, thus determining the airflow rate:
   • “LOW” – slow fan speed
   • “MID” – medium fan speed
   • “HIGH” – fast fan speed
4.  The “SWING” button causes oscillation of vertical blinds, which ensure even distribution of cooled air streams. The horizontal blinds do not move automatically – you can move them manually.
5.  The “COOL” button reduces the temperature of the exhaust air by activating the water pump. Two plastic containers (11) are included in the set. To use plastic containers placed them in the freezer for about a day first. Then insert one or both of them into top water tank (2. The “COOL” function also moisturizes the air.
6.  During operation of the device, periodically check the water level for refilling the tank. Do not activate the “COOL” function if the water level is lower than the minimum level.
7.  To end the operation of the device, press the “OFF” button on the control panel.

CLEANING AND MAINTENANCE

It is recommended to clean the device with a soft, dry cloth. Do not use any chemical solvents as they may permanently damage or deform the surface. If the device will not be used for three months or longer, remove the batteries from the remote control. Pour water out of the tank before storage by opening the drain plug (8). Dry the device to avoid moisture damage. Set the “COOL” button to the highest fan speed, the device should work for about 10 minutes to dry the internal filter (5).

TECHNICAL DATA

• Supply voltage: 220-240 V ~ 50/60 Hz
• Power: 65W
• Maximum power: 350W
• Capacity: 12L
• Water consumption: 1-2 liters / hour

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>