PIXEL SXMLCR72 Satellite Radio Compact Motorcycle Kit Instruction Manual

June 5, 2024
PIXEL

TECHNOLOGIES

SXMLCR72Satellite Radio Compact Motorcycle Kit
Installation Instrucons

Package Includes

(1) SiriusXM™ PowerConnect™ Vehicle Cradle
(1) SiriusXM™ 5 Volt Hardwired Power Adapter
(1) Handlebar Clamp Mount
(1) RAM Ball Mount Adapter (25 MM)
(1) Weatherproof Protecve Case
(1) SiriusXM™ Antenna
(1) Auxiliary Cable
(1) L-Bracket with AMPS Plate & Lock Ring
(1) AMPS Plate (Male Dual Notch) with Screws

PIXEL SXMLCR72 Satellite Radio Compact Motorcycle Kit -
Fig

Step 1 – Install Clamp Mount
Before ge ng started, it is important to select an installa on loca on for the protec ve case with receiver. A er selec ng the installa on loca on for the protec ve case, loosen the two screws on the handlebar clamp mount all the way out and separate it from the back side of the clamp mount. Place the clamp mount on the handlebars, line up the screw holes and ghten the screws to mount the clamp. Use the supplied rubber strips to increase the grip of the mount.PIXEL SXMLCR72 Satellite Radio Compact Motorcycle Kit -
Clamp

BACKPLATE ASSEMBLY

Locate the bag containing the parts shown below.PIXEL SXMLCR72 Satellite
Radio Compact Motorcycle Kit - containing

Step 2 – Place the parts as pictured below. Take the AMPS Socket Plate and place it on one side of the L-bracket. Next place the Dual Male AMPS Plate on the opposite side as the AMPS Socket Plate and line up the screw holes. Please note the posi oning of the Dual Male AMPS Plate with the notches at the bo om. The dual notches must be posi oned at the bo om in order to properly seat into the back of the case. Use the supplied screws and nuts to secure the plates to the L-bracket. The mount can be assembled with the top plate of the L-bracket facing forward or backwards to fit your installa on needs. Next, slide the L-bracket assembly onto the back of the protec ve case. The case should slide down over the dual notches.PIXEL SXMLCR72 Satellite Radio
Compact Motorcycle Kit - fit

Optional – RAM Mount Assembly

To install the kit onto a RAM mount, use the RAM Mount Adapter Plate located in the supplied parts bag. Screw the RAM Mount Adapter Plate to the L-bracket with the Dual Male AMPS Plate on one side and the RAM Mount Adapter Plate on the other side. The mount can be assembled with the top plate of the L-bracket facing forward or backwards to fit your installa on needs. Next, slide the L-bracket assembly onto the back of the protec ve case. The case should slide down over the dual notches.PIXEL SXMLCR72 Satellite Radio Compact Motorcycle
Kit - RAM Mount Adapter

Step 3 – Connect Mount to Back Plate and Mount Antenna
To connect the handlebar or strap mount to the back plate, insert the ball joint into the AMPS Female Socket Plate with the Lock Ring having the wide end facing towards the socket plate. Push the mount into the socket un l it clicks. Once the ball joint is firmly in place, screw the Lock Ring clockwise un l it ghtens all the way. To change the angle of the case, loosen the ring and pivot the case then re ghten the Lock Ring to secure. Do not over ghten the Lock Ring to avoid damaging it. Next, place the antenna on the metal L-bracket and run the antenna wire through the bo om of the case connec ng it to the antenna port on the dock.PIXEL SXMLCR72 Satellite Radio Compact
Motorcycle Kit - Antenna

Step 4 – Connect Power
Included in the package is a hardwired power adapter. Find a power source on the motorcycle, either in a fuse box or an auxiliary power source on the motorcycle. The hardwired power adapter comes with two interchangeable cables, one older Sirius and XM receivers and one for newer SiriusXM™ PowerConnect™ receivers. For installa ons with an older 5 volt Sirius or XM receiver (non PowerConnect™), use the cable with the smaller connector p. For installa ons using the supplied PowerConnect™ docking cradle, you will use the cable with the larger tip.

PIXEL SXMLCR72 Satellite Radio Compact Motorcycle Kit - Connect the
cables

Step 4 – Connect Audio
Included in the kit is an auxiliary cable for audio. Connect the auxiliary cable to the aux input on the motorcycle sound system, headset or another audio system. Run the auxiliary cable to the loca on of the mount and leave the cable loose. If you are installing a Bluetooth dock, FMDA25, or using wireless FM transmission, refer to that products user guide for installa on.
Step 6 – Connec ng Docking Cradle
A er all cables have been run to the protec ve case, feed the wires up through the bo om of the case shown in the image on the right. Pull enough cable through to allow for extra play in the wire in case acable is pulled. If there is extra antenna wire, it is recommended to wrap up the excess antenna wire inside the protec ve case.
PIXEL SXMLCR72 Satellite Radio Compact Motorcycle Kit -
CradleNext, connect each cable to the corresponding port on the dock.
(Some docks may have the connec ons on the sides and not the back as shown in the figure to the right)
Note: If installing a Bluetooth SiriusXM™ Dock, only power and antenna are required. The FM port on the dock is not used unless installing the FMDA25 Direct Wire Audio Adapter.
After all connections have been made, slide the receiver down onto the dock and power on the unit. If installing a new SiriusXM™ receiver, follow the instruc ons on how to ac vate the receiver provided in the receiver’s user guide.
To learn more on how to operate your specific receiver refer to the SiriusXM Radio user manual that came with the receiver.

Pixel Technologies, Inc.
|www.pixelsatradio.com |
contactus@pixelsatradio.com |
800-595-0845 |

References

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals