Pixel HK 10222 Lark X LED Photography Light User Manual
- June 6, 2024
- Pixel HK
Table of Contents
Pixel HK 10222 Lark X LED Photography Light
Safety Notes
- Do not store the product in a place with high temperature or high humidity.
- The product is getting warm while using, which is a normal situation.
- Warning: Do not keep this product in a place where there are corrosive chemicals.
- There are precise electronic circuits in this product. Please contact authorized personnel for maintenance. Any failures caused by unauthorized disassembly are not covered by our company’s warranty.
- The user guidance is prepared based on this company’s rigorous test, the design and specifications are subject to change without further notice.
FCC STATEMENT
FCC compliance statement
This device complies with Part 15 of the FCC Rules. Operation is subject to
the following two conditions: (1) this device may not cause harmful
interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation.
Warning : changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
NOTE: This equipment has been tested and found to comply with the limits
for a Class B digital device, pursuant to Part 15 of the FCC Rules. These
limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates, uses and
can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio
communications. However, there is
no guarantee that interference will not occur in a particular installation.
If this equipment does cause harmful interference to radio or television
reception, which can be determined by turning the equipment off and on, the
user is encouraged to try to correct the interference by one or more of the
following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
LIST OF ITEMS
PRODUCT VIEW
-
Built-in Microphone
-
Power Button
Long press the power button to turn on or turn off the microphone. Short press the power button to switch between the original sound mode and the noise reduction mode after the microphone is on. -
LED Indicator
-
Off: Shut down
-
White: Original sound
-
Yellow: Noise reduction
When the power is lower than 15%, the indicator light flickers. -
Charging at power on: the indicator shows the breathing state in the color of the current mode and the breathing state stops when it is fully charged.
-
Charging at power-off: the indicator light turns purple at the breathing state, and the light goes out when it is fully charged.
-
-
Charging Port
Type-C charging port, also used as a pairing mode communication port.
PRODUCT VIEW
-
The Charging Port
Charging: Use the charger to connect to the power supply. During the charging process, the battery icon at the bottom of the LED screen is in breathing state and the LED color indicates the battery power (Green for sufficient, Yellow for low, Red for insufficient). In the power-on state, the battery icon is solid green when it is fully charged; in the power-off, the battery icon is off when it is fully charged. -
Power Button: long press the power button to turn on or turn off the receiver.
-
Volume+: Short press the volume button to increase the volume. Long press to match the left channel and switch channels.
-
Volume-: Short press the volume button to reduce the volume. Long press to match the right channel and switch channels.
-
Background Audio Input Port: The audio cable can be used to connect mobile phones, computers and other devices to input background sound.
-
Headphone Jack: Headphones can be plugged in for real-time monitoring.
-
Full-tone (microphone+ background sound) Output Port: Connect to mobile phones, computers and other devices by the audio cable .
-
LED Display
ICON DESCRIPTION
Signal Strength: Greenlight (stable signal), Yellow light (general signal), Redlight (poor signal), Off-light (no signal); When there is no signal, the receiver will not be paired with the transmitter. No information is displayed on the screen at this time.
2 Receiver/Transmitters’ Battery power: Green (high battery), Yellow (medium battery), Red (low battery).
Channel Numbers: When the receiver was paired with transmitters successfully, the number indicates 1-18 channels. It also can indicate volume value by 1-10 when pressing the volume button.
Noise reduction mode: White (original sound), Yellow (noise reduction). Short press the power button of the transmitter to switch the mode.
Voice Level: Green (normal), Yellow (small), Red (too small to record); Speaking volume and the environment noise influence the color display.
NOISE REDUCTION FUNCTION
-
Low-Frequency Noise Reduction
Reduce low-frequency noise such as wind noise, environmental noise, vibration noise, etc. -
High-Frequency Noise Reduction
Reduce high-frequency noise such as howling and electronic noises.
HOW TO USE
Connect the Receiver
-
Connect the listening and recording device to the corresponding interface, as shown in the picture below.
HOW TO USE -
The receiver can be installed on the camera for use, as shown in the picture below.
HOW TO USE -
The receiver can be installed on the phone for use, as shown in the picture below.
-
Suitable for lossless transmission of 6.5mm interfaces of mixing console, power amplifier, speakers, etc., as shown below.
Installation of the Signal Enhancement Antenna
The signal enhancement antenna can improve the signal stability of the wireless microphone, which is suitable for outdoor or other complex application scenarios. Connect the transmitter to the antenna, refer to the figure below for specific operations.
Note:
To ensure the audio quality, it is recommended to attach the antenna in the
following situations:
- The transmitters are far away from the receiver and recording equipment.
- Continuously moving or turning your back on the receiver.
- There are noises or clicking sounds due to signal interference and other problems.
Power On
long-press the power button 2 seconds to switch On/Off.
-
Automatic Pairing
long-press the power button of the receiver and transmitter and they will be automatically paired after start up. -
Switch between wireless communication channels.
- a) Connect the transmitter to the receiver using the Type·C charging cable and match to the left channel by pressing and holding the volume”+” button (press and hold the volume”+” button again and the microphone unit randomly selects channel 1 to 18).
- b) Connect the transmitter to the receiver using the Type-C charging cable and match to the right channel by pressing and holding the volume”-” button (press and hold the volume “-” button again and the microphone unit randomly selects channels 1 to 18).
-
Set Single/Dual Microphone Audio Channel
- a) Single microphone mode Turn on one transmitter and pair it with the receiver successfully.
- b. Dual microphone mode Turn on both transmitters and pair them with the receiver successfully.
TROUBLESHOOTING
No signal/ Noise existed
| The effective using distance outdoors is 65.6ft
(20 meters). When the distance exceeds the using range, noise may occur with no signal. If the mic is needed to be used under the shelter or in an indoor place, the working distance will be decreased.
When the current channel frequency signal is disturbed, there may be noise. Please connect the transmitter and receiver and then switch the channel again.
---|---
The sound is distorted
|
The microphone is a high-sensitivity pickup. Please adjust the distance between the microphone and the sound source. Please check the corresponding settings of the recording device and whether the audio adapter cable is connected correctly.
Short using distance
|
The effective distance may be affected because the transmitter and the receiver are blocked by the building;
The transmitter and receiver should not be covered by any object to facilitate signal transmission;
The human body may also attenuate the radio waves in a crowded environment, then the transmitter and the receiver shall not be blocked as much as possible;
When the current signal channel is interfered, please switch the transmitter and the receiver to different channels.
Howling existed
| ****
When the sound is picked up by the microphone and then extended by mixers, peripheral device, power amplifiers, and speakers, there may be howling. Please turn down the output volume of the microphone, raise the audio amplifiers’ volume, and moderately adjust the distance between these two devices mentioned above.
---|---
Audio
discontinuity
| ****
The signal of the current channel is weak. We sincerely advise that you could adjust to an appropriate channel before streaming. Please plug in the external antenna when using the microphone outdoor.
No sound/ Very small
| ****
Check whether the output plug of the receiver is fully inserted into the socket. Check the
corresponding settings of the recording devices, and whether the audio adapter cable is connected correctly.
Check whether the audio adapter cable is compatible with your recording device. Adapter cables are available for purchase from the official T-mall store.
SPECIFICATIONS
Working Frequency| ****
590.777MHz to 607.662MHz
---|---
Transmit Power
| ****
0.78mW
Receiver Sensitivity
| ****
<-108dBm@12dBSINAD
RF Deviation
| ****
SOkHz@lkHz 94dB SPL
Working Distance
| ****
<20 meters (65.6ft)
Audio Response
| ****
100Hz-10kHz±3dB
Distortion
| ****
<1%@1kHz 94dB SPL
Signal to Noise Ratio| 79dB
Stand-by Current
| ****
<O.SuA
Working Current
| Transmitter: <75mA (4 hours battery life*2) Receiver: <170mA (8 hours battery life)
Weight
| Transmitter: Approx. 23g/0.81oz Receiver: Approx. 85g/3oz
Dimension(mm/inch)
| Transmitter: 2Y20’71mm/0.82’0.78’2.8in(L’W’H)
Receiver: 57.5’30’85.5mm/2.26’1.18’3.37in(L •w•H)
PART NAME
- Transmitter 1 Charging Slot
- Receiver Charging Slot
- Transmitter 2 Charging Slot
- Transmitter 1 Power Indicator
- Receiver Power Indicator
- Transmitter 2 Power Indicator
- Powe Display Button
- Type-C Charging Interface
HOW TO USE
Charging
The charging interlace is Type-C version, which can be charged with USB
charger or Type-C charger (this product supports QC/PD fast charging).
Note: The flashing LED on the charging case indicates that the charging case is being charged. If the LED is always on, it indicates the charging case is basically full-charged.
Installation
Open the charging case, put the transmitter and the receiver into the charging
slots, and dose the charging case.
Note:
Insert the microphone device or short press the button on the charging case to
activate the LED power indicator. The LED indicator turns off after about 3
seconds without operation. If there is no microphone device in the case, the
LED indicator does not light up when short press the button.
Charging with Charging case
The color of the LED indicates the charging status of the microphone in the charging case (corresponding to transmitter 1, receiver, and transmitter 2). Short press the button on the charging case to activate the LED battery indicator, which lights up different colors to indicate power status of the microphone device. The LED indicator turns off after about 3 seconds without operation.
Charging Case connected to Type-C Cable for Charging
Led color/flashing indicates the charging status of the microphone and
charging case (corresponding to Transmitter 1, Receiver, Transmitter 2).
Connect the Type-C charging cable, and the white light automatically lights up
to show the power status of the charging case. Short press the power display
button to check the power status of the microphone device, and the display
remains for 3 seconds.
Note:
The charging case will automatically shut down when the power is about to run
out, so you need to access the charging cable to charge until the charge is
activated.
Charging Case Power Display Button
Press the power display button until the white indicators light up, it flashes to indicate the power status of the charging case, and the display remains for 5 seconds. (You can press the button to check the power status of the charging case whether there are microphone devices in the case or not.)
HOW TO USE
SPECIFICATION
Name
| ****
Lark X Charging Case
---|---
Model
| ****
Lark X
Type of Battery
| ****
Lithium-ion polymer battery
Built-in lithium Battery
| ****
3.7V/4400mAh (16.28Wh)
Battery Life
| Fully rechargeable twice for devices in the charg ng case
Charging Port
| ****
Type-C
Input Power
| ****
5V=2A 12V=2A 9V=2A
Fast Charging Protocol
| ****
PD3.0 QC 2.0
Charging Case Charging Time
| ****
As fast as about 80 minutes
(fast charging)
Materials
| ****
Plastic+ Aluminum Alloy
Dimension
| ****
110•110•37mm/ 4_33•4_33•1.46in
Weight
| ****
268g/ 9.45oz
Add:
Building 2 No. B71, Dalang section Guanzhang Road, Dalang Town, Dongguan,
China
E-mail:
pixel@pixelhk.com
Support: support@pixelhk.com
User: retail@pixelhk.com
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>