MUNBYN B08GC19TM3 Keyboard Emulator Barcode Scanner with Pistol Grip User Manual
- June 5, 2024
- MUNBYN
Table of Contents
MUNBYN B08GC19TM3 Keyboard Emulator Barcode Scanner with Pistol
Introduction
This document aims to guide customers on how to use KeyboardEmulator. KeyboardEmulator is an internal software application to test barcode-scanning and RFID-reading functions. Meanwhile, it can be used in some basic business scenarios depending on the customer’s choice. In KeyboardEmulator, there’re four main sections and one additional function part. Following we will introduce them one by one. Please review this document for more information and details.
Function
There’re 2 main parts under this section, one is for Barcode, the other one is for UHF. By following, we show you how to trigger a side-button/pistol to trigger barcode-scanning or RFID-reading.
Barcode
If customers would like to use side button/pistol to trigger Barcode-reading,
please follow below steps: a. – put the cursor on the input box, then press
side button/pistol, its key-code will appear automatically. b. – tick the
checkbox of barcode. c. – toggle Off to On. After finish above steps, then you
can use side button/pistol to trigger barcode scanning.
UHF
If customers would like to use side button/pistol to trigger UHF-reading,
please follow below steps:
- put the cursor on the input box, then press side button/pistol, its key-codewill appear automatically
- tick the checkbox of UHF
- toggle Off to On
AppSettings
This section is basically for some specific settings from the KeyboardEmulator
level Under this section, it will cover below 8 parts:
- basic function
- Process mode
- End mark
- Data format
- Continuous scan
- Virtual scan button
- Factory scan button
- Debug
Basic Function
Release key of scan – if you realse scan key, then scanning would stop. Success Sound – if scan successfully, there will be sound as a reminder. Failure sound – if failed to scan, there will be sound as reminder. Vibrate – if scan successfully, there will be vibration as reminder (the premises device is with vibration sensor). GS1 Parsing – in this mode, when scan GS1 barcodes, all characters of the GS1barcode will be read. Block scan key – this is to block scan key value, can leave it if it’s not necessary. Barcode Not Repeat – on this mode, repeated barcodes will not show when scanning. Disable control of scanner – this is to stop other apps fromcontrollingKeyboardEmulator.
Process mode
Scan content on cursor – the data will show up in the place with cursor
simultaneously. Clipboard – read-out data will be saved in the clipboard, and
can be paste directlyto anywhere with the cursor. BroadcastReceiver – it is
the method that uses the broadcast mechanism of Android to transfer data to
the customer’s program. Keyboard input – the data will show up together in the
input box with the cursor.
End mark
The end mark means adding a specific mark at the end of read-out data. Enter – tick this checkbox, the output will be word-wrapping automatically. the read- out data will be added with the tab character-“\t” suffix. when data is acquired in Excel, the cursor will move to the next cell automatically.
Data Format
Under this section, you can choose different data formats listed in the below
picture for Barcode and RFID accordingly based on specific requirements. And
to meet further demand, there’re 5 more features that might be applied in some
basic scenarios. Prefix: the prefixing numbers or letters will be added to the
output. e.g if you input ‘ABC’, and the original barcode is ‘12345’, then the
final output will be as ‘ABC12345’. Suffix: the suffixing numbers or letters
will be added to the output. e.g if you input ‘ABC’, and the original barcode
is ‘12345’, then the final output will be as ‘12345ABC’. Remove the number of
characters from the front: input 1, the first digit will be trimmed. input 2,
the first two digits will be trimmed, and so on. Remove the number of
characters from the back: input 1, the last digit will be trimmed.
Continuous scan
There’re two main parts under this section, one is for Barcode, and the other
is for UHF. Barcode Just like literal meaning, it will enter into continuous
scan mode when ticking the continuous checkbox. And under the continuous mode,
you can choose [Normal
Mode] or [Zebra Mode]:
- 【Normal Mode】 – there will interval between each scanning
- 【Zebra Mode】 – there is no interval between each scanning
Meanwhile, there’re 2 parameters available to be adjusted:
Time out – if input 10s and scanning light is moved away from tags and can focus on tags again within 10s, then the scanning light will be off. Interval – if input 10 ms, then the interval of the continuous scan will be 10ms. To stop the continuous scan, just uncheck the box of a continuous scan. UHF checks the box of the continuous scan, then it will enter continuous scan mode. Before entering the continuous mode, there’re 3 parameters (timeout, interval, output power) available for you to adjust under this model. Timeout Interval Output power – can choose from 1 to 30 dBm, the reading performance is inproportion to the output power, which means, the higher you set output power, thebetter reading performance you will get. Plus, you can also choose to read the EPC or TID of the RFID tags by selectingthe EPC or TID checkbox.
Virtual Scan button
Under this section, you can choose to use the virtual button to trigger
barcode-reading or UHF-reading
Factory data reset
By clicking ‘factory reset’, the setting you made previously in keyboardEmulator will be removed and back to the original status.
Save log
After tick the checkbox, all your actions in KeyboardEmulator will be
savedinbelow path: File Manager > scanner > data
2DSettings
This section is basically for setting from the scanner level. we’ve integrated
some common settings here. Under this section, you will find ‘base setting’
and somecommon barcodes of 1D and 2D.
Base setting
Under this section, customers can do settings according to their specific
requirements. We will only introduce【picklist mode】and【security level】here due
to limited. For further and more details, please refer to the technical
documents for the scanner accordingly
Common Barcodes
We’ve integrated some common barcodes into KeyboardEmulator, like UPC/EAN,
EAN-8, EAN-13 and etc. They’re visible under this section, and customers can
easilyset accordingly. The right side is the live example-1 for reference.
Adding parameters
For those scanner functions that’s invisible under the 2D setting, we can
addthespecific function via the below way (referring to below the pic.). And
About what parameters shall be used, pls refer to technical documents of
scanners for details.
Addition Functions
Under this section, there’re 7 functions. 4.1 QR code-WIFI
- QR code-ScannerConfig
- Black white list
- Version Update
- Firmware upgrade
- Refresh log
- Barcode Test
In the following, we will introduce them one by one.
QR code-WIFI
QR code-ScannerConfig
Black white list
Version Update
This function is not available yet.
Firmware upgrade
This function is not available yet (only available for the zebra scanners).
Barcode Test
Select ‘Barcode Test’, you will enter the left page. Here you can select ‘compare’ or‘Auto’. Compare – The 1 st read-out barcode will be the sample, and the following read-out barcodes will compare with the sample barcode. If same then will count as success, if different then count as an error. Auto – this equals continuous scan mode, and you can adjust the interval accordingly.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>