GIRA 24211290 EnOcean Wireless Wall Transmitter Instruction Manual

Operating instructions

EnOcean wireless wall transmitter
1-gang 2421 ..
2-gang 2422 ..
EnOcean wireless wall transmitter

Safety information

Electrical devices may only be installed and connected by a qualified electrician.
Serious injury, fire or damage to property is possible. Read and observe these instructions completely.
Wireless transmission takes place via a non-exclusive transmission path and is thus not suitable for applications in the security technology sector such as emergency-off or emergency calls. These instructions are part of the product and must stay with the customer.

Device components

Figure 1 Figure 2

1. Rocker 1-gang or 2-gang
2. Wireless module
3. Cover frame
4. Base plate
5. Adhesive dots
6. Adhesive film

Function

System information
This device is part of the EnOcean system.
The range of a wireless system depends on various external factors. This range can be optimised by the ideal choice of the installation site.

Intended use

• Wireless transmitter for the transmission of switching, dimming and blind commands to a wireless receiver of the EnOcean wireless system.
• Installation on device box in compliance with DIN 49073 or on smooth, level surfaces using screws or adhesive bonding.

Product properties

• A battery-free device without an external power supply.
• The transmission energy is generated from mechanical energy by actuating the rocker.
• Encrypted wireless transmission is possible.

Operation

Transmitting wireless telegrams

• Press and release the rocker (1) to send a wireless telegram.

Installation

To achieve good transmission quality, ensure sufficient distance to possible sources of interference, e.g. metal surfaces, microwave ovens, hi-fi systems, TV sets, ballasts and
electronic transformers.

Note
A higher contact pressure is required for initial installation. Observe TOP designation.

Adhesive mounting (Figure 1)

• Ensure that the surface is clean, free of grease and able to bear the load.
• Apply the adhesive film (6) beforehand in the case of transparent surfaces.
• Apply adhesive dots (5) to the surface or to the adhesive film (6) in the case of transparent surfaces.
• Press the baseplate (4) onto the adhesive dots. G Pay attention to the mounting direction ofthe base plate (TOP marking).
• Place the cover frame (3) onto the baseplate.
• Attach the wireless module (2).
• Attach the rocker (1).

Screw mounting (Figure 2)

• Mount the baseplate (4) on a device box or directly on the wall.
  G Pay attention to the mounting direction of the base plate (TOP marking).

•  Place the cover frame (3) onto the baseplate.

•  Attach the wireless module (2).

• Attach the rocker (1).

Start-up

The following operating modes are available:

• Unencrypted transmission, as delivered.
• Explicitly encrypted transmission.
• Implicitly encrypted transmission. This operating mode should only be used if older wireless receivers do not support the explicit operating mode.

Note
The wireless module can only work in one of the operating modes. The wireless module and all wireless receivers must have the same operating mode.

Wireless module

Figure 3

S0 Power button
S1-S4 Function buttons
Connect wireless wall transmitter with wireless receiver
In order for a wireless receiver to understand a wireless telegram from the wireless wall transmitter, this wireless wall transmitter must be connected to the wireless receiver (see instructions for wireless receiver).

Operating mode: Unencrypted transmission

• Activate programming mode on the wireless receiver (see instructions for wireless receiver).
• Press and release the rocker (1) to send a wireless telegram.

Operating mode: Explicit encrypted transmission

• Remove rocker (1) from the wireless module (2).
• Activate mode for encryption on the wireless receiver (see instructions for wireless receiver).
• Press and hold down function buttons (S1+S2+S3).
• Press the power button (S0) twice.
• Place rocker (1) on wireless module (2).
• Activate programming mode on the wireless receiver (see instructions for wireless receiver).
•  Press and release the rocker (1) to send a wireless telegram.

Operating mode: Implicit encrypted transmission
Only use this operating mode if the wireless receiver  does not support explicit encryption.

• Remove rocker (1) from wireless module (2).
• Activate mode for encryption on the wireless receiver  (see instructions for wireless receiver).
• Press and hold down function buttons (S1+S2).
• Press power button (S0) twice.
• Place rocker (1) on wireless module (2).
• Activate programming mode on the wireless receiver (see instructions for wireless receiver).
• Press and release the rocker (1) to send a wireless telegram.

Restoring the delivery state

• Remove rocker (1) from the wireless module (2).
• Press and hold down function buttons (S1+S2+S3+S4).
• Press the power button (S0) twice.
  The operating mode “unencrypted transmission” is set.

Technical data

Transmission range
in free field:| up to 300 m
in buildings:| approx. 30 m
Ambient temperature:| -25 to +65 °C
Humidity:| 0 to 95% (no condensation)

Conformity

Gira Giersiepen GmbH & Co. KG hereby declares that the wireless system type, item no. 2421 .. and 2422 .., conforms to Directive 2014/53/EU. The complete item number can be found on the device. The complete text of the EU declaration of conformity is available at the following Internet address: www.gira.de/konformitaet

Warranty

The warranty is provided in accordance with the statutory requirements via the retailer. Please submit or send faulty devices postage paid and with a fault description to your sales representative (retailer/installation company/electronics retailer). They will forward the devices to the Gira Service Centre.

http://b.gira.de/2421:2422

Gira
Giersiepen GmbH & Co. KG
Elektro-InstallationsSysteme
Industriegebiet Mermbach
Dahlienstrasse
42477 Radevormwald, Germany Postfach 12 20
42461 Radevormwald
Germany
Tel +49(0)21 95 – 602-0
Fax +49(0)21 95 – 602-191
www.gira.de
info@gira.de
10868410 / 22/06/2021

Documents / Resources

| GIRA 24211290 EnOcean Wireless Wall Transmitter [pdf] Instruction Manual
24211290 EnOcean Wireless Wall Transmitter, 24211290, EnOcean Wireless Wall Transmitter
---|---

References

• Schalter, Steckdosen & smarte Technik | Gira

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>