LOCKLY PGA300RF Wireless Transceiver User Manual
- June 5, 2024
- LOCKLY
Table of Contents
LOCKLY PGA300RF Wireless Transceiver
Installation & User Manual
Lockly Guard Wireless Transceiver is built with F433.92MHz and Lockly 2.0 proprietary encryption to provide stable wireless connectivity, security and reliability. It operates on 12V DC from the Access Control power supply and supports high-level or low-level of PUSH and monitors door open/closed status of the electromagnetic lock*. It is very quick and easy to install anywhere.
- To remove cover, slide the bottom of the case as shown.
- Refer to the wiring diagram Insert cables through the bottom hole and connect to corresponding wireless transceiver terminals : PUSH GND, GND, +12V and LOCK NC. Then connect the cables to the corresponding terminals on the Access Control Power Supply : PUSH, V-, V+ and LOCK NC to electromagnetic lock NC terminal. Ensure you followed the wiring diagram and cables are connect-ed to the corresponding terminals. Tighten the screws to secure the cables.
- The NC port is used to detect the opening and closing status of the door. Only the Lockly Guard Electromagnetic Lock supports this function. If you use a third-party Electromagnetic Lock other than the Lockly Guard Works ONLY with Lockly Electromagnetic Lock. Connection to NC of the LOCK NC cable is required.3. Pair Wireless Transceiver to the Lockly Guard Ingress or Ingress VisionAccess Control power supply will activate the Wireless Transceiver. Wireless Transceiver Blue light indicator will be ONonce connected to Ingress or Ingress Vision. Refer to theIngress/Ingress Vision Manual for pairing instructions.
Short Press the wireless transceiver pairing button to start connecting with Ingress/Vision, Blue light indicator flashes whenpairing starts. It will automatically exit pairing mode if pairing is successful. If pairing is unsuccessful, it will continue to flash and automatically exits in 3 minutes.Short press the wireless transceiver pairing button again tore-enter pairing mode. How Wireless Transceiver and Ingress/Ingress Vision WorksWhen wireless transceiver is activated through the smart access control power supply, the Blue light indicator turns ON when the door locks or unlocks. When the electromagnetic lock (LOCK NC) is triggered, the Blue light indicator turns ON.
FCC Warning
This device complies with Part 15 of the FCC Rules. Operation is subject to
the following two conditions: (1) This device may not cause harmful
interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation.
NOTE 1:
This equipment has been tested and found to comply with the limits for a Class
B digital device, pursuant to part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates, uses and can radiate radio
frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications. However,
there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and
on, the user is encouraged to try to correct the interference by one or more
of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
NOTE 2:
Any changes or modifications to this unit not expressly approved by the party
responsible for compliance could void the user’s authority to operate the
equipment.
FCC Radiation Exposure Statement
The Secure Link Wi-Fi Hub complies with FCC radiation exposure limits set
forth for an uncontrolled environment. It should be installed and operated
with minimum distance 20cm between the radiator & your body.
IC WARNING
This device contains licence-exempt transmitter(s) that comply with
Innovation,Science and Economic Development Canada’s licence-exempt RSS(s).
Operation is subject to the following two conditions:
- This device may not cause interference.
- This device must accept any interference, including interference that may cause undesired operation of the device.
IC Radiation Exposure Statement
This equipment meets the exemption from the routine evaluation limits in
section 2.5 of RSS-102. It should be installed and operated with a minimum
distance of 20cm between the radiator and any part of your body.
WARNING:
This product can expose you to chemicals including Lead, which is known to the
State of California to cause cancer. For more information go to
www.P65Warnings.ca.gov.
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>