LOCKLY PGD238F GUARD Defender Biometric Electronic Installation Guide

FOR COMMERCIAL USE & PROFESSIONAL INSTALLATION
PGD238F GUARD Defender Biometric Electronic
Installation Guide

Preparation

Prepare door: remove existing deadbolt or use provided template to bore new holes.

Step 1 DETERMINE DOOR OPENING DIRECTION

There are 4 common door-opening directions, the lockset configuration as shown on each diagram below corresponds to the respective door-opening direction.

LEFT OUT-SWING DOOR
Make sure the latch throw is correctly oriented as shown to fit your left out- swing door| RIGHT OUT-SWING DOOR
Make sure the latch throw is correctly oriented as shown to fit your right out-swing door
---|---
|
LEFT IN-SWING DOOR
Make sure the latch throw is correctly oriented as shown to fit your left in- swing door| RIGHT IN-SWING DOOR
Make sure the latch throw is correctly oriented as shown to fit your right in- swing door
|

IMPORTANT
This lock is designed for 35-65mm Wooden or Aluminium Door or Aluminium Thermal Barrier Door. If your door is outside the range of the list above please contact our Customer hotline: (855) 562-5599
Before installing the exterior assembly, make sure you have already adjusted your door handle (Step 2) and identified the latch throw orientation according to door opening direction.

Step 2 CHANGING HANDLE FOR RIGHT OR LEFT SWING DOORS

The diagram below shows how to shift the door handle from right to left direction. The default setting of the handle is for right handed door. You do not need to change direction if you have a right handed door.
Change the handle direction of the Exterior Assembly
Use allen wrench to loosen screws on both sides on the handle base.

Step 3 INSTALLING THE LOCKSET

Make sure your door is prepared for installation. If you need to drill new holes, please use the supplied template for drilling holes. Before installing the Lockset, confirm the door opening direction (Step 1) and ensure latch throw is on correctly oriented to the door’s opening direction.

Insert Lockset onto door hole and secure with screws (top and bottom) .

|
---|---

Step 4 INSTALLING THE EXTERIOR AND INTERIOR ASSEMBLY

1. Install the exterior assembly onto the door. Make sure the spindle, cables and rods are routed correctly through the holes in the door. Install top and bottom mounting blocks and secure with scews.
2. Connect Bluetooth receiver Rotate plugs to tighten cable connection.
3. Install top mounting block. Remove the adhesive tape at the back of Bluetooth receiver (L) and install under mounting block. Mount the (K) on the groove of the top block to secure the Bluetooth receiver.

Step 5 FINAL CHECK AND BATTERY INSTALLATION

1. Use a screwdriver to loosen the battery cover screw then open battery compartment.
2. Unplug the terminals of the battery box and install the battery.
3. Reconnect the battery box to terminals, insert to compartment and return the cover.
4. Tighten the battery screw J to secure battery cover, then install Bottom Screw Cover (I) to conceal bottom screwsTo complete installation, install door interior handle according to the user manual of your interior door handle

Step 6 DOWNLOAD LOCKLYPRO APP

Congratulations! You have completed the Lockly Guard physical lock installation. To complete your setup, download the LocklyPro app from the iOS or Google Play app Store and follow on-screen instructions.
Scan or visit Locklypro.com/app

http://Locklypro.com/app

FCC Warning:
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:

1. This device may not cause harmful interference, and
2. This device must accept any interference received, including interference that may cause undesired operation.

NOTE 1: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

NOTE 2: Any changes or modifications to this unit not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
FCC Radiation Exposure Statement
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. It should be installed and operated with minimum distance 20cm between the radiator & your body.
IC WARNING
This device contains licence-exempt transmitter(s) that comply with Innovation, Science and Economic Development Canada’s licence-exempt RSS(s). Operation is subject to the following two conditions:

1. This device may not cause interference.
2. This device must accept any interference, including interference that may cause undesired operation of the device.

IC Radiation Exposure Statement
This equipment meets the exemption from the routine evaluation limits in section 2.5 of RSS-102. It should be installed and operated with a minimum distance of 20cm between the radiator and any part of your body.
WARNING: This product can expose you to chemicals including Lead, which is known to the State of California to cause cancer. For more information go to www.P65Warnings.ca.gov.

INSTALLATION OVERVIEW AND PARTS LIST

FOR COMMERCIAL USE & PROFESSIONAL INSTALLATION
We’re here to help!
prosales@lockly.com
locklypro.com/supporthttp://locklypro.com/support
© Copyright 2022 Lockly All rights reserved
USA Patent No. US 9,881,146 B2
USA Patent No. US 9,853,815 B2
USA Patent No. US 9,875,350 B2
USA Patent No. US 9,665,706 B2
USA Patent No. US 11,010,463 B2
AUS Patent No. 2013403169
AUS Patent No. 2014391959
AUS Patent No. 2016412123
UK Patent No. EP3059689B1
UK Patent No. EP3176722B1
Other Patents Pending
WWW.LOCKLYPRO.COM
MPGD23820220916

Documents / Resources

| LOCKLY PGD238F GUARD Defender Biometric Electronic [pdf] Installation Guide
PGD238F GUARD Defender Biometric Electronic, PGD238F, GUARD Defender Biometric Electronic, Defender Biometric Electronic, Biometric Electronic, Electronic
---|---

References

• Lockly Pro-Total Access Solution for Properties & Offices
• Lockly Pro App - Lockly Pro
• Support Page - Lockly Pro
• Lockly Pro-Total Access Solution for Properties & Offices
• P65Warnings.ca.gov

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>