ZEBRONICS ZEB-LP2800HD Full HD LED Projector User Manual

ZEBRONICS ZEB-LP2800HD Full HD LED Projector

SAFETY PRECAUTIONS

Read these safety instructions before using your device and store them for possible future reference.

•  If the cord is damaged, have it repaired by the manufacturer, it’s service or a similarly qualified person in order to avoid any hazard.
•  The cord should always be readily accessible.
•  The apparatus shall not be exposed to dripping or splashing of water or liquids and that no objects filled with liquids such as flower vases shall be placed on the product.
•  The normal ventilation of the product shall not be impended for intended use.
•  Always leave a minimum distance of 10cm around the unit to ensure sufficient ventilation.
•  Open flame sources, such as candles, should not be placed on top of the device
•  The device is intended for use only in a temperate climate.
•  The ventilation should not be impeded by covering the ventilation openings with items, such as newspapers, table-cloths, curtains, etc

CAUTION:
To avoid accident, this appliance must be fixed properly on the floor or on the wall according to instructions for installation.
Danger of explosion if batteries are incorrectly replaced or not replaced by the same type or equivalent.

INTERFERENCE:
All wireless devices are susceptible to interference which may affect their performance.

AUTHORIZED PERSONNEL:
Only qualified people are authorized to install or repair this product.

ACCESSORIES:
Only use batteries, chargers and other accessories which are compatible with this equipment. Do not connect incompatible products.

VISUAL INSTRUCTIONS

Top View Control Panel Bottom View

Note: The adjustable support base can assure the max projection angle by 15°, The best display effect will be obtained by projection angle ranges of 0° – 8°. Front View Side View
Left Side Right Side

1. HDMI 1 Port
2.  HDMI 2 Port
3.  Headphone Jack (3.5mm)
4.  AV Port
5. USB 1 Port
6.  USB 2 Port

Rear View

Remote Control Note: While using the remote control, point it toward IR receiver.

Projection Distance and Size

Please follow the data in chart below, to adjust the image size and the distance. (Between the lens and screen)

The image size depends on the distance between projector and screen, there may be 3% deviation among above listed data. Different settings cause various distances.

How to Use

1.  Before starting up the projector. Follow figure below to adjust trapezoid correction. Keep the projector vertical with projector screen and keep it on the same level.
   

2. . Connect the power plug as following picture, connect with the electricity, The indicator light will turn to red.
   
   Note: Pictures are only for your reference, different countries got different power plug, please contact your supplier for more details, better connect the projector first.

3.  Press the “power” button ( ® ) on the control panel or remote control to turn on the projector.
   

Keystone and Focus

If the projected image is in a trapezoidal shape, it can be resolved by Keystone correction. (Do Manual Keystone Correction)

Note: If the Keystone correction fail to resolve image shape, please reduce the vertical height of the projector in relation to the center of the screen.
The projected image may be blurry or difficult to see, this is due to lack of Focus adjustment with the lens, please follow the processes below to adjust the Focus. (Do Manual Focus, find the most sharpness picture on the screen )

Note: It is normal when sharpness in the central, blur in the edge.

Multimedia Connection:

Insert the USB flash driver into the USB port and choose the right signal source, then press Play/Pause button ( ►II ) to display or stop.
(Press “Source” on the remote control or “S” on the control panel, then there is “Input Source” on the screen, choose “USB”)

HDMI Connection

Support most device with HDMI slot. Press “Source” on the remote control, then choose the right signal source “HDMI”.

AV Connection

Use AV cable for connecting as follows, choose the “AV’ source input.

Audio Out Connection

Connect the loud speaker as follows:

VGA Connection

Choose the “PC-RGB” source to connect computer with VGA cable, for audio output, you need to connect to a speaker separately.

Multimedia File Specification **

**

Doesn’t Support:
Dolby AC3 / MC, DTS, WMA, DivX, VC1, etc.

**

**

Doesn’t support:
MSVC I CRAM, MP42, GMC, IV32, RLE, cvid, RV20, DivX, RM, RMVB, Vc1, etc.

Features:

• Home Theater Projectors for Movies, TV & Gaming etc.
• Projector comes with VGA, HDMlx2, USBx2, AV IN &AUX OUT
• Built in Speaker
• Wide Compatibility
• Remote Control

Specification:

• Screen size: 127-305cm
• Native resolution: 1280x720p HD
• Supported resolution: 1080p (max)
• Display technology: LCD with LED lamp
• Lifespan: -30,000H
• Brightness: 2800 lumens
• Contrast ratio: 2000:1
• Projection distance: 1-4 meters
• Port Interface: VGA, HDMI x 2, USB x 2, AV IN, AUX OUT
• Video file format: AVI, MP4, MPG,
• Input Voltage: AC 100-240V, 50/60Hz
• Product dimension (W x D x H): 222 x 165 x 87mm
• Net. weight: 1.4kg

Package contents:

• Projector: 1 Unit
• Remote control: 1 Unit
• Power cord: 1 Unit
• AV cable: 1 Unit
• Support base: 1 Unit
• HDMI Cable: 1 Unit

ISO 9001:2015 Certified Company www.zebronics.com

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>