inELS 4333 4 Button Controller – Keychain User Guide
- June 5, 2024
- inELS
Table of Contents
inELS 4333 4 Button Controller – Keychain
Compatibility
The RF KEY controller (hereinafter referred to as the controller) can control all switching and dimming components of the iNELS RF Control and iNELS RF Control2 system (hereinafter referred to as the actuator)
Indication, manual control
- LED – indication of sending RF command
- Control buttons
Sending a command (when pressing and releasing the control button) is
indicated on the RF KEY by a fl ashing LED.
In the programming and operating mode, the LED on the component lights up at
the same time each time the button is pressed – this indicates the incoming
command.
Insertion and replacement of a battery
-
Using a Phillips head screwdriver, remove the screw on the back of the transmitter. Remove the rear cover.
-
Carefully remove the device from the box.
-
Slide the CR2032 battery into the battery holder. Observe the polarity
-
Insert the device into the housing so that it clicks onto the tabs and to the stops inside the housing.
-
Replace the rear cover and replace the screw.
Safe handling
When handling a
device unboxed it is important to avoid contact with liquids. Never place the
device on the conductive pads or objects, avoid unnecessary contact with the
components of the device.
Radio frequence signal penetration through various construction materials
80 – 95 %| 80 – 90 %| 60 – 90 %| 20- 60 %|
0 – 10 %
---|---|---|---|---
wooden structures with plaster boards| common glass| brick walls| reinforced
concrete|
metal partitions
ELKO EP declares that the RF Key type of radio equipment complies with
Directive 2014/53 / EU.
The full EU Declaration of Conformity is available at: www.elkoep.com/4
-channel-controller—keychain-white
Programming with RF transmitters
Press of programming button on actuator RF for longer than 1 second will
activate actuator RF into programming mode. LED is fl ashing in 1s interval.
Press the selected control button on the RF controller according to the
desired function (for more information on the individual functions and
programming of the RF controls, see the manual of the specifi c components).
Must be a lapse of 1 s between individual presses.
Press of programming button on actuator RF shorter then 1 second will
fi nish programming mode.
Technical parameters
| Supply voltage: | 3 V battery |
|---|---|
| Transmission indication: | red |
| Number of buttons: | 4 |
| Transmitter frequency: | 866 MHz, 868 MHz, 916 MHz |
| Signal transmission method: | unidirectionally addressed message |
| Range in free space: | up to / až 200 m |
| Other data | |
| Operating temperature: | -10 … +50 °C |
| Operating position: | any |
| Protection: | IP20 |
| Contamination degree: | 2 |
| Dimensions: | 64 x 25 x 10 mm |
| Weight: | 16 g |
| Related standards: | EN 60669, EN 300220, EN 301489 R&TTE Directive, Order. No |
426/2000 Coll.
(Directive 1999/EC) / EN 60669, EN 300 220, EN 301 489 směrnice RTTE,
NVč.426/2000Sb (směrnice 1999/ES)
Attention:
When you instal iNELS RF Control system, you have to keep minimal distance 1
cm between each units.
Between the individual commands must be an interval of at least 1s.
Warning
Instruction manual is designated for mounting and also for user of the device.
It is always a part of its packing. Installation and connection can be carried
out only by a person with adequate professional qualifi cation upon
understanding this instruction manual and functions of the device, and while
observing all valid regulations. Trouble-free function of the device also
depends on transportation, storing and handling. In case you notice any sign
of damage, deformation, malfunction or missing part, do not install this
device and return it to its seller. It is necessary to treat this product and
its parts as electronic waste after its lifetime is terminated. Before
starting installation, make sure that all wires, connected parts or terminals
are de-energized. While mounting and servicing observe safety regulations,
norms, directives and professional, and export regulations for working with
electrical devices. Do not touch parts of the device that are energized – life
threat. Due to transmissivity of RF signal, observe correct location of RF
components in a building where the installation is taking place. RF Control is
designated only for mounting in interiors.
Devices are not designated for installation into exteriors and humid spaces.
The must not be installed into metal switchboards and into plastic
switchboards with metal door – transmissivity of RF signal is then impossible.
RF Control is not recommended for pulleys etc. – radiofrequency signal can be
shielded by an obstruction, interfered, battery of the transceiver can get fl
at etc. and thus disable remote control.
The company ELKO EP, as the manufacturer, is entitled to make technical modifi cations to the product, in the technical specifi cation and product manual, without prior notifi cation.
ELKO EP, s.r.o.
e-mail: elko@elkoep.cz
Support: +420 778 427 366
References
- 4-channel controller - keychain white • ELKO EP
- 4-tlačítkový ovladač - klíčenka RF Key bílá/černá • ELKO EP s.r.o
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>